Linksys Access Point :: No Connection On Casio DT-X5M10R When Two AP Power On
Oct 12, 2011
I have a problem about no connection on casio handy terminal when two access point were power on. The devices were link with Cisco access point. for the other one i use dlink access point for the wifi function. I need to switch off dlink access point to make the connection between the device and the cisco access point.
1st access point :
Dlink DAP-1360
Default IP: 192.168.2.29
Channel:1
SSID Broadcast: Enable
2nd access point :
Cisco Aironet 1240AG
Default IP: 192.168.3.33
Channel:6
SSID Broadcast: Disable
View 1 Replies
ADVERTISEMENT
Dec 3, 2011
My WAP54G no longer has power -- the power light does not come on. I've unplugged the unit and moved it to a variety of different outlets that I know work.
View 5 Replies
View Related
Aug 20, 2012
I just bought a WAP160N to replace our WAP54G because my Samsung Glaxay 3 could not use the internet through our WAP54G (not sure if Galaxy 3 doesn't like G mode networks). The problem we have after installing the WAP160N is that the signal doesn't extend as far in the house as the WAP54G. We have the routers up the front end of the house (the WAP160N is wired to our Netcomm router) and when you go to the kitchen (in the middle of the house) the signal from the WAP160N is being lost/fluctuating, then dropping on devices such as iPads. We have WAP160N set to mixed mode on 2.4Ghz, AES or TKIP. I tried setting it to 5Ghz but that didn't work either. We always had signal strength in the kitchen when using the WAP54G. if the WAP160N can not extend its signal further or the same distance as the WAP54G? I find it odd that the iPads can't hold the connection in the kitchen, when we've always been able to use internet/wifi there. I'm thinking of returning the WAP160N if the signal cannot extend far enough. router that can extend the signal far throughout a house?
View 1 Replies
View Related
Jun 11, 2011
i am trying to connect my new Iphone 4 to my wireless connection which is a cisco wap610n. I get a fails to connect error. mine and other laptop can connect using my security key. the Iphone can connect to other wireless connections. my access point connects to a linksys RT31P2 router?
View 1 Replies
View Related
Jan 21, 2011
I have 2 WAP54G AP. I have office with internet connection near my home. How to connect these access points so i can get access to internet from home, but don't won't to anyone else can access that.
View 1 Replies
View Related
Feb 22, 2012
My Access Point Power Led blinks constantly, Lan led works normally, Wlan led never turns on.
Access Point: D-Link DWL-2100AP
View 6 Replies
View Related
Apr 21, 2013
I have a problem, where we are installing a Cisco 2602 access piont, the AP is getting power as the lights are on (changing colors Green, White, Red). In the switch side the LED for the interface is blinking green only when I chosse PoE. Also I cannot see the AP in CDP neighbours.
It seems to be a physical problem but the cable is tested and showing connected for all pairs and parallal (straight) connection.
Access Point was connected directly to the same interface (I mean with a patch cable to the switch) and working
View 4 Replies
View Related
Mar 17, 2013
To extend my wired ethernet I have purchased a WAP300N access point and connected it according to the instructions. I can see the AP from a wireless client and connect, but no IP number is provided to the client. The AP is connected to a router which has a DHCP server via wired connection (though a switch). The AP does it self get an IP number from the router but does not pass through DHCP requests from the clients.Occasionally an IP number is provided, but then there is no route to the LAN or the WAN on the other side of the AP.I have tried a whole lot of things to make it work (and been in the internet chat for two hours with a Linksys supporter, who could not make it work either).I have tried to set the IP number in the AP to static.I have tried to remove security (has to be WPA2 eventually, but for the sake of testing it has been removed)I have tried to factory resetI have tried to reinstall the firmware (the same version as the factory installed)etc.
View 4 Replies
View Related
Jun 13, 2011
I had the WAP610N for a few months with no issues. As always, I have a custom SSID and password, using WPA2. All of a sudden, none of my mobile units (at least 5) are unable to connect via the WAP610N. However, I can connect to a Netgear N750 w/o any issues. When I reboot the WAP610N, it resolves the issue for a few minutes, but then behaves the same as before. I know its not my network because, I am able to connect via wired and wireless via the Netgear. I verified via the web interface that none of the settings/configurations have changed - but still nothing. Latest firmware has been applied. Note sure If I should perform a factory reset or re-apply the firmware.
View 2 Replies
View Related
Sep 19, 2012
I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
Wlc 5508
Ap 1242
7.0.220.0
View 3 Replies
View Related
Jul 16, 2011
I'm trying to share my existing wireless connection over a WAP54G with the latest firmware, on Windows 7 on a laptop. Basically, the laptop is getting a wireless connection from my Sprint Card, but I need to share a wi-fi connection with an iPod I'll be using to validate tickets. Unfortunately, there is no option to share the wireless connection when I click on the Properties for the connection. When I put in my WiFi settings, the iPod is able to login to the AP, but it cannot obtain an IP. It keeps doing this. Same thing happens with my Samsung Epic which runs Android. I can access the AP manager, and can configure it. Have tried using no security, but still no dice. Even turned off the firewall.
I can surf the internet on the laptop, but I simply can't share the connection with the AP. This is really important as I'm trying to get it setup by next weekend!
View 2 Replies
View Related
Aug 18, 2011
I have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.
View 1 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 7, 2011
When the WAP54G is set up as a repeater for a WRT54G, will a computer connected to the LAN port on the WAP54G be able to connect to the network? I know it will see the WAP54G if I manually set it's ip address.
I guess I want it to act as a wireless NIC for the desktop while also operating as a repeater. Is this possible? If not, will one of the other AP settings like Bridge allow the wired connection to connect to the other side of the network and give wireless access to wireless devices? I've hacked up and attached one of Linksys's diagrams to show what I'm trying to do. It seems to me the easiest thing to do would be to buy a wireless NIC for the desktop.
View 5 Replies
View Related
Mar 3, 2011
I work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
View 2 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Jul 11, 2012
I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
View 4 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jun 12, 2007
Cannot access configuration page for WAP11 Access
View 9 Replies
View Related
Jun 14, 2011
I know that vista and win 7 dont have hyperterminal. but here is the deal in my building i have 9 proxim 4000 wireless access points in my building. Using the scan tool i can see all of them but the IT guy that was here who installed them did not leave a map are diagram of where they are all located and so when i was installing the updated firmware one of them went back to default so now i cant access it from the scan tool are http. i have to find it and use a rs-232 serial connection to connect to it when i find it. and reading the instructions for the proxim 4000 says i will have to use hyperterminal cli to set everything again.how to use hyperterminal for connecting to access points.
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Aug 31, 2011
So I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point. I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc). However, I can't establish a wireless connection to the access point.
- Defined a IP address for the DIR-655 within the DHCP range of the primary router
- Defined the proper subnet
- Disabled the DHCP server on the DIR-655
- Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).
When I connect a device WIRED to a LAN port on the DIR-655, everything works fine. The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem. So I know the DIR-655 is acting correctly to pass thru traffic. Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.
But when I try to connect WIRELESS to the DIR-655, it doesn't work at all. Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.
View 5 Replies
View Related
Jul 5, 2012
How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access
View 1 Replies
View Related
