Cisco :: 4402 Access Point Configured In User Minimum
Mar 13, 2012need an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies
ADVERTISEMENT
Cisco :: Maximum Limit For Access Point On WLC 4402
Oct 13, 2011We are expanding our wireless infrastructure by adding further access points AIR-AP1242AG-E-K9.We use four WLC 4402 running version 6.0.188.0 as a fail over pair.What is the maximum limit the WLC can handle ?What is the recommended limit one WLC can handle ?We can divide the load on the controllers but in case of a failover one WLC will manage all access points.
View 4 Replies View RelatedCisco :: Information For Connecting Access Point To WLC 4402
Nov 15, 2011I need Some information for Connecting my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
View 38 Replies View RelatedCisco Wireless :: AIR LAP1142N Access Point Configured And SSID Broadcasted
Mar 7, 2012We have an autonomous AIR-LAP1142N-E-K9 AP with software release version 12.4(25d)JA1. The access point is configured and an SSID is broadcasted. However when users are trying to connect to the AP, authentication seems to be accepted but users are not connected. I suspected the issue in DHCP but even on static IP the user is not connected.I dont believe any LAN issue is there cause I connected a PC to the same interface where the AP is connected and it took an IP from the required VLAN (1234) [code]
View 3 Replies View RelatedCisco Wireless :: 262N Lightweight Access Point Work With 4402
Apr 4, 2012Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies View RelatedCisco :: 1130 - Aironet Access Point Not Able To Connect By User
Jun 12, 2011I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
Linksys Access Point :: X2000 Does Not Accept New User Connections
Mar 3, 2013I am having an issue with the mentioned AP, it does not accept new user connections, however new user can connect after the AP is restarted.I would like to know if there is a limit on the number of wifi users for linksys x2000?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Can't Seem To Enable In ASA With Non-15 Privilege Level User Configured In ACS 4.2
Apr 29, 2011I can't seem to enable in ASA with a non-15 privilege level user configured in ACS 4.2 (tacacs).When I enable in IOS device, it enables and "show privilege" shows level 10 as expected. ACS should be configured correctly as it works fine with IOS. User is not set with explicit settings. Group is set with "max enable level" 15 and "shell exec priv level" 15. The enable password is set to the internal ACS PAP password. Works fine in IOS.When I enable in ASA, it fails to enable, and ACS log says "Tacacs+ enable privilege too low". I suspect that ASA tries to enable into level 15 explicitely. If I try to issue "enable 10" command in ASA it says: Enabling to privilege levels is not allowed when configured for AAA authentication. Use 'enable' only. [code]
View 2 Replies View RelatedCisco :: 4402 WLAN Controller - User Getting Disconnected?
May 29, 2013I have a Cisco 4402 Wireless LAN Controller and 4 x AIR-LAP1131AG-A-K9 access points.We run a combination of [WPA +WPA2]Auth(802.1x) as well as [WPA2]Auth(PSK), most people have their own login credentials...The primary client devices are MacBooks and iPhones, with some Windows and other mobile manufacturer being the minority.
The Issue I have one user (using a recent MacBook Air, latest OS, using Auth(802.1X) ), that keeps getting disconnected for no apparent reason, the user account has been setup exactly the same as every other user and his laptop doesn't have this issue when connected to other WiFi networks.It's worth noting: I noticed this particular user has a lot of "Decrypt Failed" (currently 213) associated with his MAC address, no other user on our network has a single "Decrypt Failed" associated with their MAC...
Cisco :: 4402 - WCS User Names Sometimes Incorrect With 802.1x FreeRadius
Feb 29, 2012I'm not sure if this is a recent issue for our setup, but I've only just noticed it. Although most authenticated users are shown by their correct user names (which are required for 802.1x authentication), a few users show up in the WCS reports as "anonymous", and one as "anonymous@myabc.com", which are not valid usernames on our network.
I can track these users by MAC via our network registration database, but have not yet figured what makes their systems unique. All three in yesterday's report are Win 7. I don't see anything strange in the RADIUS logs, but have not yet caputured "debug" traces of wireless authentication from an anonymous user.
We are running WCS 7.0.172.0 , with a pair of WLC 4402 controllers running 7.0.116.0 . Our WPA2 Enterprise auth uses TTLS/PAP, with the SecureW2 supplicant for Windows.
Cisco Wireless :: Not Able To Register AP Point On 4402 WLC Running IOS
Jul 15, 2012Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies View RelatedCisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 User Roles And Restricting User Access To Add Items?
Sep 22, 2011We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Cisco :: 5508 AP Configured As Rogue Detector And Configured Switch Port
Jul 21, 2011I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View RelatedLinksys Access Point :: WAP54G Access Point Setup After A Reset?
Jul 9, 2006I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedLinksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point
Jan 17, 2013I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedLinksys Access Point :: WRT320N Access Point Vs Range Extender
Dec 14, 2011Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedLinksys Access Point :: WAP4410n MIBs Or OIDs For Access Point
Jul 3, 2012I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Linksys Access Point :: Repeat WAP54G Access Point?
Aug 25, 2011What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedLinksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Linksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedLinksys Access Point :: E3000 Configuration As Access Point?
Apr 6, 2011I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedLinksys Access Point :: Way To Find Mib For WAP54G Access Point?
Feb 10, 2012I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedCisco WAN :: Unable To Access Newly Configured 1841 Via SSH Or Via CCP?
Oct 24, 2011Im unable to access my newly configured 1841 via SSH or via CCP from the WAN side.
Is there anything I can do from the LAN side in CCP that will assure that this router is able to be managed from the WAN?
Cisco VPN :: ASA5510 Configured Remote Access To Allow Users Log In Via SSL VPN
Apr 12, 2011We have a high availability pair of ASA 5510's in Data Centre where we have configured remote access to allow users log in via SSL VPN, now we want to add further security to our environment we are adding endpoint assessment licenses...the question I have would I need two sets of the license ASA-ADV-END-SEC ?
I learned the hardway before with ASA SSL VPN licenses breaking other failover pair as it needed identical licenses on both units! Will I need 2 separate license sets to keep my firewalls in a HA pair?
Cisco :: 4402 - Allow Certain Ip To Access To Log In Page Of WLC
Apr 29, 2013I have a cisco WLC 4402, i have a problem with people trying to log into wlc 4402 GUI console with wrong pass. Are there any ways that I can allow certain IP to go to or see the log in page of WLC?
View 5 Replies View RelatedCisco VPN :: Configured Remote-access VPN On ASA 5510 - Cannot Reach Network
Mar 14, 2011I configured a remote-access vpn on an ASA 5510 version 8.3. This is the configuration [code]The vpn goes up and I get an ip address, but it's impossible to reach the internal network. [code]
View 9 Replies View RelatedCisco :: Lot Of Templates Configured And 1500 Access Points Applied
May 31, 2012I need to Upgrade my NCS to version 1.1.0.58. Actually my NCS is in the version 1.0.1.4 and i have a lot of templates configured and 1500 Access Points applied.
I have 5 WLCs and will do too the upgrade in the WLCs to version 7.2.130.0.
Will I lose some configuration with these upgrades ? Because the version 1.1.0.58 has more features than version 1.0.1.4 in the NCS and the WLC was adjusted some bugs.
The configurations that i has in the NCS version 1.0.1.4 is H-REAP and in the version 1.1.0.58 will be the FlexConnect, theoretically is the same, but i don't know if the configuration is the same in the two versions.
Can i do a downgrade in the NCS from version 1.1.0.58 to 1.0.1.4 if i have problems ? I was looking for a document who show how can i do this, but i didn't find nothing about.