I configured a remote-access vpn on an ASA 5510 version 8.3. This is the configuration [code]The vpn goes up and I get an ip address, but it's impossible to reach the internal network. [code]
View 9 RepliesI am trying to configure remote access VPN to my network, i have a Cisco ASA 5510 IOS 7.0(7).
I configured the VPN using ASDM 5.0.9 and below is the configuration received:
access-list 90 extended permit ip 192.xxx.xxx.0 255.255.255.0 192.xxx.xxx.248 255.255.255.248
access-list ClientVPN_splitTunnelAcl standard permit 192.xxx.xxx.0 255.255.255.0
ip local pool VPNIpPool 192.xxx.xxx.250-192.xxx.xxx.252 mask 255.255.255.0[code].....
We have a high availability pair of ASA 5510's in Data Centre where we have configured remote access to allow users log in via SSL VPN, now we want to add further security to our environment we are adding endpoint assessment licenses...the question I have would I need two sets of the license ASA-ADV-END-SEC ?
I learned the hardway before with ASA SSL VPN licenses breaking other failover pair as it needed identical licenses on both units! Will I need 2 separate license sets to keep my firewalls in a HA pair?
I have a Cisco ASA 5510. I have configured Cisco Anyconnect to authenticate via Windows IAS. We had an outage of that server recently and I tried to remote in via anyconnect and could not. Once the IAS server came up I could get back into the network.
Is there a command that I'm missing that will let me use Anyconnect to connect into the network even if my AAA server is down?
I am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedSo, I've set up Anyconnect client access to an ASA-5510.
I've got a handful of interfaces, which contain hosts that should be accesible to anyconnect clients. I'm unable to reach addresses on a specific network, due to what packet-tracer claims is an implicit deny, though I'm unsure where to apply an access-list in this case.
fw1# show nameif
Interface Name Security
Ethernet0/0.205 SECURE 90
[Code].....
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
I have a asa 5510 vpn client groups configured and connected to the internal network DHCP server stops giving network service dhcp and the network goes down.
View 6 Replies View RelatedI have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies View Related I have a problem with a Remote Access VPN on a ASA 5510 8.6.2 .I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources. [code]
I have a (central) ASA5510 acting as a EasyVPN server and a number of (remote) ASA5505 as EasyVPN client. All the communication works fine between the different networks. The issu is the ASA itself. The remote ASA can ping the central ASA on it's internal IP-adress, but it can't ping any other resoruces at the central network. If I ping the DC at the central network from the remote ASA I get a deny in the central ASA with source address as the public IP-adress of the remote ASA and destination of the internal address of the DC. If I from the remote ASA do "ping inside ip-of-central-dc" it work's like a charm, but "ping ip-of-central-dc" dosen't work.
View 3 Replies View RelatedI have configured Clientless SSL VPN for access to ASA 5540 internal network. Still I am unable to take ssh to my core switc [code]
View 5 Replies View RelatedI want to setup remote access for my Android phones and tablets using Cisco ASA 5510 . Is there any particular Android client which perform the specified functionality.
View 1 Replies View RelatedI have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
I have an end user who uses the Anyconnect VPN client to connect to our network through an ASA5510. He has a satellite ISP provider and is experiencing latency issues. Since latency issues are inherent with satellite services and since he has no other ISP alternative, any tweaks that may boost performance/reduce latency with his connection. Typcally, he sees slow performance and also network drives being intermittently available on his Windows 7 computer. he also has an internal wireless router at his home when he connects remotely. Performance when connected through a standard cable broadband connection is fine.
View 2 Replies View RelatedI'm having some troubles with SSLVPN connectivity. I've setup SSLVPN at one site and it works great with web access, file share, RDP plugin etc. at the local LAN on that site. But I also would like to reach another site (connected with an IPSEC tunnel). Is this possible? if it is, how do I do it?Both firewalls are ASA5505, one 8.31 and one 8.22 Just a note, it works to connect with IPSEC client and reach the remote site just fine.
View 8 Replies View Related-cisco 2651xm router
-cisco 1760 router
I have a cisco 2651xm router here at home, and at another remote location I have a cisco 1760 router, both are connected to the internet via adsl (WIC1-ADSL card).The problem is that from home I can't connect to the snmp-service on the 1760 router. I'm using a PC that's on the LAN of the 2651XM router, the blockage is in the 2651XM router, because if I swap it for a cheap plastic domestic router I can get snmp data from the 1760 router, and this is without any port forwarding in the domestic router. What config do I need on the 2651XM router so it will pass this traffic?
We are facing strange issue in our network. We have a remote branch which is connected to main branch using Leased Line. Remote branch is having Cisco 1700 Router. Every day in the morning time the remote router is unreachable. We are not able to reach (ping/telnet) the remote Router but able to reach L3 switch/ LAN behind this router. The users from remote branch is also not able to reach the local router but they are able to ping the Main branch.Users in the remote branch are not able to access any resources in the main branch during the issue.
During the issue, we have checked the remote branch router and found the CPU utilization of the Cisco 1700 router is very high (99%). If we run "Show process CPU" command (please find the attachment) specially IP input process is very high (97%).
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies View Relatedip local pool VPNPOOL 192.168.200.1-192.168.200.100.
i can access servers with remote vpn which they located at dmz zone at asa(write nonat access-lsit) but i can not 192.168.193.0 subnet at asa.i configurated proxy server. my proxy server inside interface get ip address my dmz zone(172.16.10.254) and outside is ip adddress asa outside interface (10.0.0.254).the users (192.168.193.0/24) go internet from proxy server.
[code]....
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
!
ASA Version 8.2(5)
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.6.0.12 255.255.254.0
[code]....
I am having trouble making my remote access vpn decrypt traffic. I am using an ASA5510 and the cisco 5.0 vpn client. I have no problem getting the tunnel to come up. But the "decrypted traffic" stays zero and the "discarded traffic" increments continuously.Here is the ASA5510 crypto config:OK I guess this site doesn't allow pasting text so I attached the config.I am pretty sure that I can't pass traffic because I have not been able to figure out how to specify the interesting traffic for the vpn connection. What is the syntax for this? It looks like it should be some kind of tunnel- group commands.
Am I the only one who thinks that the Cisco documentation is worthless on this subject? The ASA config guide gives you everything you need to set up a tunnel, but has absolutely nothing on the config required to actually pass traffic.
Router: ASA 5510
We have changed the ISP, so therefore new wan ip-addresses.
Internet works, and site-to-site vpn works, but I'm failing to localice why the remote access vpn won't work.
I have a problem with ASA 5510 8.0(4) This is a remote-access VPN setup and it's functional, no problems here...
But I keep getting logs like this every few seconds:
Group = <censored>, Username = <censored>, IP = <censored>, Reaper overriding refCnt [0] and tunnelCnt [0] -- deleting SA!
Group = <censored>, Username = <censored>, IP = <censored>, SA lock refCnt = 0, bitmask = 00000080, p1_decrypt_cb = 0, qm_decrypt_cb = 0, qm_hash_cb = 0, qm_spi_ok_cb = 0, qm_dh_cb = 0, qm_secret_key_cb = 0, qm_encrypt_cb = 0
I have a cisco ASA 5510 that I have set up currently to access via ASDM through the Inside interface. When I VPN in using our older VPN server I can connect to it fine. I recently set up the ASA to also be a VPN server which will eventually replace the older server for our HQ. I noticed that when I'm VPN using the ASA as the VPN server, I can only ASDM to the public which I prefer not to allow. Access to the inside doesn't seem to work this way. What configurations if any would be causing this. I'm assuming it's some thing I need to adjust in the VPN configuration.
View 3 Replies View RelatedI have a ASA 5510 configured for IPSec remote access VPN.It works nicely and can see the private LAN behind the ASA.My problem is that I have other networks connected to this ASA via site-to-site tunnels that I would like to open up to remote access.
I have added these networks to the split-tunneling ACL's and added NAT exemptions for those networks.This doesn't seem to work.
I need a way to block MAC OS X users connecting remotely to our coporate users over VPN. I know there is an option to block connections based on VPN client Version, but cant find a way to block users based on operating system.
We use Cisco ASA 5510 firewals one with v8.2(1) and other with v7.2(3). I need to do on both firewalls. They are both at diffrent sites.
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
!
ASA Version 8.2(5)
!
interface Ethernet0/1
[Code]....
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies View RelatedWe got the below alert when we ran the PCI scan on our VPN firewall (use it for remote access VPN).
OpenSSL SSL_OP_NETSCAPE_REUSE_CIPHER_CHANGE_BUG Ciphersuite Disabled Cipher Issue
Solution- Upgrade to OpenSSL 0.9.8j or later.
ASA 5510 running 8.2(2)
Is the following sysntax correct in removing a remote access vpn address pool and inserting a new one on an ASA5510?
(config)# NO ip local pool BWCVPN 192.168.200.1-192.168.200.128
(config)# ip local pool BWCVPN 192.168.300.1-192.168.300.128
(confif)# tunnel-group BWCVPN ciscovpn general-attributes
(config-general)# address-pool BWCVPN
I have successfully installed and configured VPN Client - Version 5.0.07 to connect to ASA 5510 from a remote workstation. Here is the problem, I cannot ping any of the servers or workstations after I successfully connect. I can ping the ASA 5510 using its internal LAN IP, but no other nodes will respond on the remote LAN.
View 2 Replies View RelatedI have 2 sites :
site A :
ASA 5510
VPN gateway for remote users
LAN 192.168.192.0/22
site B :
ASA 5505
LAN 192.168.208.0/22
Both sites are connected through a site to site VPN.Remote clients (AnyConnect/VPN client) can connect to Site A LAN and see machines on LAN A but cannot see Site B LAN.
Here is a part of my configuration :
On Site A (ASA 5510)
--------------------------------
name 192.168.192.0 SiteA_Internal_Network
name 192.168.208.0 SiteB_Internal_Network
name 192.168.133.0 VPNPool_AnyConnect
name 192.168.133.32 VPNPool_VpnClient
[code]....