I am having trouble making my remote access vpn decrypt traffic. I am using an ASA5510 and the cisco 5.0 vpn client. I have no problem getting the tunnel to come up. But the "decrypted traffic" stays zero and the "discarded traffic" increments continuously.Here is the ASA5510 crypto config:OK I guess this site doesn't allow pasting text so I attached the config.I am pretty sure that I can't pass traffic because I have not been able to figure out how to specify the interesting traffic for the vpn connection. What is the syntax for this? It looks like it should be some kind of tunnel- group commands.
Am I the only one who thinks that the Cisco documentation is worthless on this subject? The ASA config guide gives you everything you need to set up a tunnel, but has absolutely nothing on the config required to actually pass traffic.
I need to count the bytes for some interesting traffic crossing the firewall in ASA 5500. Packet Capture is so far as I need, cause I only need the number of bytes during a long time for about 3 months (source host - destination host)
capture capin type raw-data access-list cap buffer 33554432 interface inside circular-buffer [Capturing - 33553570 bytes]
I need to get only the exactly amount of "33553570 bytes" The pcap file is not needed
I have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
I have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 22.214.171.124 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
I have an end user who uses the Anyconnect VPN client to connect to our network through an ASA5510. He has a satellite ISP provider and is experiencing latency issues. Since latency issues are inherent with satellite services and since he has no other ISP alternative, any tweaks that may boost performance/reduce latency with his connection. Typcally, he sees slow performance and also network drives being intermittently available on his Windows 7 computer. he also has an internal wireless router at his home when he connects remotely. Performance when connected through a standard cable broadband connection is fine.
I am trying to configure remote access VPN to my network, i have a Cisco ASA 5510 IOS 7.0(7).
I configured the VPN using ASDM 5.0.9 and below is the configuration received:
access-list 90 extended permit ip 192.xxx.xxx.0 255.255.255.0 192.xxx.xxx.248 255.255.255.248 access-list ClientVPN_splitTunnelAcl standard permit 192.xxx.xxx.0 255.255.255.0 ip local pool VPNIpPool 192.xxx.xxx.250-192.xxx.xxx.252 mask 255.255.255.0[code].....
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
ip local pool VPNPOOL 192.168.200.1-192.168.200.100.
i can access servers with remote vpn which they located at dmz zone at asa(write nonat access-lsit) but i can not 192.168.193.0 subnet at asa.i configurated proxy server. my proxy server inside interface get ip address my dmz zone(172.16.10.254) and outside is ip adddress asa outside interface (10.0.0.254).the users (192.168.193.0/24) go internet from proxy server.
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
! ASA Version 8.2(5) ! interface Ethernet0/1 nameif inside security-level 100 ip address 10.6.0.12 255.255.254.0
I have a cisco ASA 5510 that I have set up currently to access via ASDM through the Inside interface. When I VPN in using our older VPN server I can connect to it fine. I recently set up the ASA to also be a VPN server which will eventually replace the older server for our HQ. I noticed that when I'm VPN using the ASA as the VPN server, I can only ASDM to the public which I prefer not to allow. Access to the inside doesn't seem to work this way. What configurations if any would be causing this. I'm assuming it's some thing I need to adjust in the VPN configuration.
I have a ASA 5510 configured for IPSec remote access VPN.It works nicely and can see the private LAN behind the ASA.My problem is that I have other networks connected to this ASA via site-to-site tunnels that I would like to open up to remote access.
I have added these networks to the split-tunneling ACL's and added NAT exemptions for those networks.This doesn't seem to work.
I need a way to block MAC OS X users connecting remotely to our coporate users over VPN. I know there is an option to block connections based on VPN client Version, but cant find a way to block users based on operating system.
We use Cisco ASA 5510 firewals one with v8.2(1) and other with v7.2(3). I need to do on both firewalls. They are both at diffrent sites.
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
Is the following sysntax correct in removing a remote access vpn address pool and inserting a new one on an ASA5510?
(config)# NO ip local pool BWCVPN 192.168.200.1-192.168.200.128 (config)# ip local pool BWCVPN 192.168.300.1-192.168.300.128 (confif)# tunnel-group BWCVPN ciscovpn general-attributes (config-general)# address-pool BWCVPN
I have successfully installed and configured VPN Client - Version 5.0.07 to connect to ASA 5510 from a remote workstation. Here is the problem, I cannot ping any of the servers or workstations after I successfully connect. I can ping the ASA 5510 using its internal LAN IP, but no other nodes will respond on the remote LAN.
site A : ASA 5510 VPN gateway for remote users LAN 192.168.192.0/22 site B : ASA 5505 LAN 192.168.208.0/22
Both sites are connected through a site to site VPN.Remote clients (AnyConnect/VPN client) can connect to Site A LAN and see machines on LAN A but cannot see Site B LAN.
Here is a part of my configuration :
On Site A (ASA 5510) -------------------------------- name 192.168.192.0 SiteA_Internal_Network name 192.168.208.0 SiteB_Internal_Network name 192.168.133.0 VPNPool_AnyConnect name 192.168.133.32 VPNPool_VpnClient
We have configured site to site VPN tunnel from offshore to client location using ASA5510 and accessing RDP from client location. Also configured remote VPN access at offshore location. But using remote VPN client we are able to get RDP from officeshore location but not able to access RDP from client location. Is there any additional changes required ?
Last time, i´ve implemented a Remote Access VPN to my network with ASA 5510 I´ve allowed to my VPN an acces to all my Internal LAn But i want to configure a group of vpn in the CLI for have different group of user which can access to different server or different network on my LAN.
Example : informatique group------access to 10.70.5.X Network Consultor group -------- access to 10.70.10.X Network
I need to know how can i do that , and if you can give me some eg script for complete this Here is my configuration :
ASA Version 8.0(2)!hostname ASA-Vidruldomain-name vidrul-ao.comenable password 8Ry2YjIyt7RRXU24 encryptednamesdns-guard!interface Ethernet0/0 nameif outside security-level 0 ip address X.X.X.X 255.255.255.X!interface Ethernet0/1 nameif inside security-level 100 ip address X.X.X.X 255.255.255.X!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 shutdown no nameif no security-level no ip address!interface Management0/0 description Port_Device_Management nameif Management security-level 99 ip address X.X.X.X 255.255.255.X management-only!passwd 2KFQnbNIdI.2KYOU encryptedftp mode passivedns server-group DefaultDNS domain-name vidrul-ao.comaccess-list 100 extended
I've set up a remote access group for Anyconnect on a 5510 running 8.4.5. Our company security policy prohibits split tunneling, but this particular location has no internal DNS (so I have to use a public DNS like google or something). How do I get this to work, I'm assuming I need to do a NAT exemption but I'm not sure how this would look, especially under 8.4.5.
I have a Cisco 5510 which has remote access VPN configured.Now I have new block of IP address, is there a way I can just change the outside interface IP so that people can remote in without doing anythng else?Or if I coulds be taught to create a new one.Or best way to approcah this issue?For example: it was 67.64.x.x now I need to change to 64.44.x.x.
I have a Cisco ASA 5510. I have configured Cisco Anyconnect to authenticate via Windows IAS. We had an outage of that server recently and I tried to remote in via anyconnect and could not. Once the IAS server came up I could get back into the network.
Is there a command that I'm missing that will let me use Anyconnect to connect into the network even if my AAA server is down?
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
I have a situation here where the company is rapidly expanding through acquisition. They are essentially a holding company and own several smaller entities. However most IT is consolidated as new entities are brought in and run out of Headquarters because the Board of Directors/Executive Mgt do not see IT as important and so the budget is extremely limited.
They have approximately 200 remote users at any given time, but they all work for these smaller entities. Currently each location has its own Dedicated Internet Access and VPN appliance (Netgear ProSafe, Cisco ASA 5510, I know of one entity that is just port forwarding to each workstation for RDP ).
They would like to route all traffic back through Corporate so they can consolidate this VPN mess and quit paying for all different kinds of licensing, and also stop paying for dedicated internet access for each location and just use the MPLS and have all traffic inbound/outbound run out of the corporate office.
The only issue is they dont want users to be able to access network resources at other organizations.
Like I said earlier the Board of Directors/Executive Mgt do not see IT as important and so the budget is extremely limited; so if there is an OpenSource option available that would be best. Also the IT dept there is 3 people (IT Manager (IBM AS400 guy), two Helpdesk guys (no certs, HS GED)) So the knowledge resources are limited as well.