Cisco VPN :: ASA 5510 - Remote Access Setup / Keep Getting Logs
Apr 17, 2011
I have a problem with ASA 5510 8.0(4) This is a remote-access VPN setup and it's functional, no problems here...
But I keep getting logs like this every few seconds:
Group = <censored>, Username = <censored>, IP = <censored>, Reaper overriding refCnt [0] and tunnelCnt [0] -- deleting SA!
Group = <censored>, Username = <censored>, IP = <censored>, SA lock refCnt = 0, bitmask = 00000080, p1_decrypt_cb = 0, qm_decrypt_cb = 0, qm_hash_cb = 0, qm_spi_ok_cb = 0, qm_dh_cb = 0, qm_secret_key_cb = 0, qm_encrypt_cb = 0
View 1 Replies
ADVERTISEMENT
May 25, 2011
I have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies
View Related
Mar 24, 2013
I have a problem with a Remote Access VPN on a ASA 5510 8.6.2 .I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources. [code]
View 13 Replies
View Related
Mar 23, 2011
I was trying to setup an Remote Access VPN using ISR 2801. I was able to establish the vpn tunnel from my house using DSL Connection (behind NAT), the ISR give the IP address which is from the ip pool that I configured on the ISR. The problem that I have right now is that it fails reaching the corporate LAN network.
[code]....
View 6 Replies
View Related
Feb 20, 2012
I want to setup remote access for my Android phones and tablets using Cisco ASA 5510 . Is there any particular Android client which perform the specified functionality.
View 1 Replies
View Related
Mar 1, 2012
I have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
View 3 Replies
View Related
Apr 21, 2013
I have an end user who uses the Anyconnect VPN client to connect to our network through an ASA5510. He has a satellite ISP provider and is experiencing latency issues. Since latency issues are inherent with satellite services and since he has no other ISP alternative, any tweaks that may boost performance/reduce latency with his connection. Typcally, he sees slow performance and also network drives being intermittently available on his Windows 7 computer. he also has an internal wireless router at his home when he connects remotely. Performance when connected through a standard cable broadband connection is fine.
View 2 Replies
View Related
Aug 12, 2012
I am trying to set up Remote access vpn in 1841 router. The vPN client is connecting to router, but cannot ping to remote LAN Here is the config.
Current configuration : 3625 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I am not getting any hit on the deny statement of 102 when i try pinging to client ip address (10.0.0.10).
View 2 Replies
View Related
Jun 2, 2013
I have setup a Remote access VPN on my ASA5505 firewall through the ASDM wizard.I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows incoming Rx packets. However, Tx packets remain 0, so no traffic is going out. My ASA5505 is configured as router on a stick with 25 different VLAN's. I want to restrict traffic to one specific VLAN using a crypto map.When I issue a ping -t command on my connected Windows box, the firewall log shows me the following message:
"IKE Initiator unable to find policy: Intf outside, Src: 10.7.11.18, Dst: 172.16.1.1."
"This message indicates that the IPSec fast path processed a packet that triggered IKE, but IKE's policy lookup failed. This error could be timing related. The ACLs that triggered IKE might have been deleted before IKE processed the initiation request. This problem will most likely correct itself." [code] I have really no idea what's going on. I have setup a Remote access VPN countless times but this time it shows me the error as described above.
View 5 Replies
View Related
Oct 3, 2012
I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are:
When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. what else I have to do to allow remote management access?
UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.
View 1 Replies
View Related
Sep 23, 2011
I am trying to configure remote access VPN to my network, i have a Cisco ASA 5510 IOS 7.0(7).
I configured the VPN using ASDM 5.0.9 and below is the configuration received:
access-list 90 extended permit ip 192.xxx.xxx.0 255.255.255.0 192.xxx.xxx.248 255.255.255.248
access-list ClientVPN_splitTunnelAcl standard permit 192.xxx.xxx.0 255.255.255.0
ip local pool VPNIpPool 192.xxx.xxx.250-192.xxx.xxx.252 mask 255.255.255.0[code].....
View 5 Replies
View Related
Jun 18, 2011
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies
View Related
Oct 20, 2011
ip local pool VPNPOOL 192.168.200.1-192.168.200.100.
i can access servers with remote vpn which they located at dmz zone at asa(write nonat access-lsit) but i can not 192.168.193.0 subnet at asa.i configurated proxy server. my proxy server inside interface get ip address my dmz zone(172.16.10.254) and outside is ip adddress asa outside interface (10.0.0.254).the users (192.168.193.0/24) go internet from proxy server.
[code]....
View 4 Replies
View Related
Nov 28, 2011
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
!
ASA Version 8.2(5)
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.6.0.12 255.255.254.0
[code]....
View 3 Replies
View Related
Feb 9, 2013
I am having trouble making my remote access vpn decrypt traffic. I am using an ASA5510 and the cisco 5.0 vpn client. I have no problem getting the tunnel to come up. But the "decrypted traffic" stays zero and the "discarded traffic" increments continuously.Here is the ASA5510 crypto config:OK I guess this site doesn't allow pasting text so I attached the config.I am pretty sure that I can't pass traffic because I have not been able to figure out how to specify the interesting traffic for the vpn connection. What is the syntax for this? It looks like it should be some kind of tunnel- group commands.
Am I the only one who thinks that the Cisco documentation is worthless on this subject? The ASA config guide gives you everything you need to set up a tunnel, but has absolutely nothing on the config required to actually pass traffic.
View 3 Replies
View Related
Jun 23, 2012
Router: ASA 5510
We have changed the ISP, so therefore new wan ip-addresses.
Internet works, and site-to-site vpn works, but I'm failing to localice why the remote access vpn won't work.
View 10 Replies
View Related
Apr 18, 2012
I have a cisco ASA 5510 that I have set up currently to access via ASDM through the Inside interface. When I VPN in using our older VPN server I can connect to it fine. I recently set up the ASA to also be a VPN server which will eventually replace the older server for our HQ. I noticed that when I'm VPN using the ASA as the VPN server, I can only ASDM to the public which I prefer not to allow. Access to the inside doesn't seem to work this way. What configurations if any would be causing this. I'm assuming it's some thing I need to adjust in the VPN configuration.
View 3 Replies
View Related
Sep 27, 2012
I have a ASA 5510 configured for IPSec remote access VPN.It works nicely and can see the private LAN behind the ASA.My problem is that I have other networks connected to this ASA via site-to-site tunnels that I would like to open up to remote access.
I have added these networks to the split-tunneling ACL's and added NAT exemptions for those networks.This doesn't seem to work.
View 21 Replies
View Related
Feb 12, 2013
I need a way to block MAC OS X users connecting remotely to our coporate users over VPN. I know there is an option to block connections based on VPN client Version, but cant find a way to block users based on operating system.
We use Cisco ASA 5510 firewals one with v8.2(1) and other with v7.2(3). I need to do on both firewalls. They are both at diffrent sites.
View 4 Replies
View Related
Jan 15, 2013
why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
!
ASA Version 8.2(5)
!
interface Ethernet0/1
[Code]....
View 9 Replies
View Related
Jul 26, 2011
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies
View Related
Jul 2, 2012
We got the below alert when we ran the PCI scan on our VPN firewall (use it for remote access VPN).
OpenSSL SSL_OP_NETSCAPE_REUSE_CIPHER_CHANGE_BUG Ciphersuite Disabled Cipher Issue
Solution- Upgrade to OpenSSL 0.9.8j or later.
ASA 5510 running 8.2(2)
View 6 Replies
View Related
Mar 17, 2013
Is the following sysntax correct in removing a remote access vpn address pool and inserting a new one on an ASA5510?
(config)# NO ip local pool BWCVPN 192.168.200.1-192.168.200.128
(config)# ip local pool BWCVPN 192.168.300.1-192.168.300.128
(confif)# tunnel-group BWCVPN ciscovpn general-attributes
(config-general)# address-pool BWCVPN
View 5 Replies
View Related
Mar 27, 2011
I have successfully installed and configured VPN Client - Version 5.0.07 to connect to ASA 5510 from a remote workstation. Here is the problem, I cannot ping any of the servers or workstations after I successfully connect. I can ping the ASA 5510 using its internal LAN IP, but no other nodes will respond on the remote LAN.
View 2 Replies
View Related
Dec 12, 2011
I have 2 sites :
site A :
ASA 5510
VPN gateway for remote users
LAN 192.168.192.0/22
site B :
ASA 5505
LAN 192.168.208.0/22
Both sites are connected through a site to site VPN.Remote clients (AnyConnect/VPN client) can connect to Site A LAN and see machines on LAN A but cannot see Site B LAN.
Here is a part of my configuration :
On Site A (ASA 5510)
--------------------------------
name 192.168.192.0 SiteA_Internal_Network
name 192.168.208.0 SiteB_Internal_Network
name 192.168.133.0 VPNPool_AnyConnect
name 192.168.133.32 VPNPool_VpnClient
[code]....
View 9 Replies
View Related
Jan 17, 2011
We have configured site to site VPN tunnel from offshore to client location using ASA5510 and accessing RDP from client location. Also configured remote VPN access at offshore location. But using remote VPN client we are able to get RDP from officeshore location but not able to access RDP from client location. Is there any additional changes required ?
View 4 Replies
View Related
Apr 7, 2011
Last time, i´ve implemented a Remote Access VPN to my network with ASA 5510 I´ve allowed to my VPN an acces to all my Internal LAn But i want to configure a group of vpn in the CLI for have different group of user which can access to different server or different network on my LAN.
Example : informatique group------access to 10.70.5.X Network
Consultor group -------- access to 10.70.10.X Network
I need to know how can i do that , and if you can give me some eg script for complete this Here is my configuration :
ASA Version 8.0(2)!hostname ASA-Vidruldomain-name vidrul-ao.comenable password 8Ry2YjIyt7RRXU24 encryptednamesdns-guard!interface Ethernet0/0 nameif outside security-level 0 ip address X.X.X.X 255.255.255.X!interface Ethernet0/1 nameif inside security-level 100 ip address X.X.X.X 255.255.255.X!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 shutdown no nameif no security-level no ip address!interface Management0/0 description Port_Device_Management nameif Management security-level 99 ip address X.X.X.X 255.255.255.X management-only!passwd 2KFQnbNIdI.2KYOU encryptedftp mode passivedns server-group DefaultDNS domain-name vidrul-ao.comaccess-list 100 extended
[code]....
View 2 Replies
View Related
May 8, 2012
I have a newly aquired asa 5505 that I just set up to the bare minimum configurations. I followed a cisco paper on how to create a "remote access vpn" setup for ipsec. I can sucessfully connect and establish a VPN, but when I try to access an inside resource from the vpn address, the asa blocks it.
Specific error is: Code...
View 17 Replies
View Related
Jul 9, 2012
I had IPAD setup IPSEC Remote Access VPN to try to conect to ASA5540 and Cat65 VPN service module(V1).I works fine on Cat65 VPN service module using IPAD client, but it is fail on IPAD client connect to ASA5540.THe message should be "VPN server is no response".My laptop Cisco VPN client(Windows 7) works fine on both (Cat65 VPN module and ASA5540).There is any special setting for IPAD client on ASA5540 ? The IPAD ios version 5.1.1.The ASA5540 version 8.4(4)1 ADSM 6.4(9) The Cat65 version is quit old binding with CatOS V12.2 etc.
View 2 Replies
View Related
May 6, 2013
I've set up a remote access group for Anyconnect on a 5510 running 8.4.5. Our company security policy prohibits split tunneling, but this particular location has no internal DNS (so I have to use a public DNS like google or something). How do I get this to work, I'm assuming I need to do a NAT exemption but I'm not sure how this would look, especially under 8.4.5.
View 1 Replies
View Related
Dec 19, 2012
I have a Cisco 5510 which has remote access VPN configured.Now I have new block of IP address, is there a way I can just change the outside interface IP so that people can remote in without doing anythng else?Or if I coulds be taught to create a new one.Or best way to approcah this issue?For example: it was 67.64.x.x now I need to change to 64.44.x.x.
View 1 Replies
View Related
Apr 5, 2011
How to designate access-list for the remote access vpn users in order to let them access specific subnet or host,asa 5510 and acs is in the picture
View 9 Replies
View Related
Mar 14, 2011
I configured a remote-access vpn on an ASA 5510 version 8.3. This is the configuration [code]The vpn goes up and I get an ip address, but it's impossible to reach the internal network. [code]
View 9 Replies
View Related
