I just picked up a WET200... connect it wirelessly to a Verizon Mifi so wired devices can get access to the Internet.
I've had zero luck connecting the WET200 to a wireless network...I've tried two different ones and I've also tried changing from WPA to WPA2.
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
View 4 Replies View RelatedI'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX
(WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I've just purchased 2 WET200 wireless bridges for our organisation, with the intention of using them to create a wireless bridge between 2 buildings.I've followed this guide here: url...and I'm unable to configure any kind of security other than WEP. More disconcertingly, the foot of that guide states:WET200 only supports WEP for the Wireless Security."Surely this can't be the case? All the marketing blurb states clearly that the WET200 supports WPA2, and I would have thought WPA2 was a given for any wireless product sold today, especially a business grade product. Have I misunderstood what this device can do?
View 4 Replies View RelatedI'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails.
View 13 Replies View Relatedafter reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies View RelatedI have a new WET200 wireless bridge and cannot authenticate to our WPA2 EAP-TLS freeradius server. Here are the steps that I have taken so far:
1. Renamed my pkcs12 client certificate to .pfx extension and imported it into the WET200.
2. Used the client certificate import password as the "Private Key Password"
3. Typed in the client "Login Name"
The freeradius server recognizes the WET200 with the entered credentials but will not authenticate. The freeradius debug log gives the following error:
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
WARNING: !! EAP session for state 0x3e833be03884222b... did not finish!
WARNING: !! Please read [URL]
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Normally, with other wireless devices the CA (ceritificate authority) certificate needs to be installed to the client as well as the pkcs12 client certificate? Is there a way to place a CA and client certificate into the WET200?What is the proper method to install certificates into the WET200 for FreeRadius EPA-TLS authentication?
I just purchased a WET200 wireless bridge. After trying a very long password for an enterprise certificate the bridge restarted and I have not been able to contact the device with the default 192.168.1.226 ip address. I have tried performing a reset even by holding the reset button in for a minute. The bridge will not ping either. I do have a power light and the wireless light flashes and the Ethernet port lights function when plugged into my laptop.
View 3 Replies View RelatedI've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP. I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
WET200 connected to wireless AP WRT54G (192.168.23.3)
WET200 IP address = 192.168.23.8
Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
I can configure the WET200 via the laptop, but not able to see anything across the bridge?
i am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View RelatedI have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
I'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails. [code]
View 6 Replies View RelatedI have a Linksys WRVA4400N router in my home office that I access my internet with throughout my house. I also have a Linksys WET200 Bridge that I want to use but can’t get them configured together. The Tech support folks keep shifting me back and forth and I’m about the throw my hands in the air. I get to the Advance Configuration setup for the WET200 and when I place the configuration URL 192.168.1.226 I get nothing. I can get to my router adjustments just unsure how to get the WET200 setting entered.
View 1 Replies View RelatedI have two separate offices in the same building that I'm trying to connect. They are physically far apart so I cannot connect them wirelessly. I have had an ethernet cable run from the main office to the second office and physically connected it to a WET200. I can see the WET200 on my router in the main office. In the second office, I want clients to be able to come in and connect wirelessly to the WET200 which will then connect them to my router and internet connection. The WET200 is the correct device for this?
View 2 Replies View RelatedI am completely new to wireless networking and know next to nothing. I own an apartment on a complex abroad and they have recently had wireless internet installed. There are some areas of the complex where the signal is very poor.
I have some Cisco small business WET200 ethernet bridging units and was wondering if these would be suitable to boost the signal in these Black spots. How to set this up or any suitable products to over come this problem.
I decided to upgrade the firmware in my WET200 so downloaded the latest firmware v1.0.10-ESTI filename WET200-ETSI_v1.0.10_200802_fw.img.Update seemed to go well, and the message came up rebooting please wait.Waited about 5 minutes whilst the message stayed the same, decided to try and close my explorer window and connect again, nothing happened.Tried to reset the unit by holding in the reset butting again nothing seemed to happen. The unit had been set up with the ip 192.168.113.4 before the upgrade but this is now unreachable, also tried the default of 192. 168.1 .226. Anything I can do/try to restore my unit, or did the update brick it?
View 3 Replies View RelatedSo I just got a wireless presentation gateway wpg 120 to connect to projector wirelessly. For me to connect to the projector i need to set wireless network to its wireless connection. But if I connect to wpg 120's connection, there is no internet access.Is there any way I can connect to two wireless network or use wpg 120 to connect to internet using it's connection.
View 3 Replies View RelatedI am trying to get a controller to work on my network. output from the switch arp table.
Internet 172.28.227.2 0 001b.d5cf.79c0 ARPA Vlan103
Internet 172.28.227.1 - 001c.b1ad.7400 ARPA Vlan103
Internet 172.28.227.12 0 001d.a1cc.b7f8 ARPA Vlan103
controller config:
Interface Name................................... management
MAC Address...................................... 00:07:0e:25:ac:a0
IP Address....................................... 172.28.227.2
IP Netmask....................................... 255.255.255.0
[code]....
The switch see's it but i can not ping or access it via web or telnet.
I have successfully setup the Cisco 2504 (AIR-CT2504-K9).
Trying to add 2 Access Points (AIR-SAP1602I-A-K9). I created static IPs for both in the router (RV180). The Access Points are connected to the PoE ports on the Cisco Switch (SG200-08P). The 2504 is connect to one of the non-PoE ports on the SG200. The SG200 is then connected to another switch (SF302-8P), which is connected to the Router (RV180), which is connected to the cable modem (Cisco DCM3000).
I am able to ping both of the access points from within the LAN, but they do not show-up on the 2504 console.
I have a medical office and am trying to connect my netbook to the office networkThe netbook can connect to the internet via wireless. I want the netbook to connect to the network drive that has my office data and program. How can I get the netbook to see the network drive on the server
View 2 Replies View RelatedI have a PC network in house using a netgear router. One of the PC is cable-connected to the router and the other using wireless network adapter. Now I have a Sony Blueray player which support network connection. How do I connect it to the network?
View 1 Replies View RelatedMy problem is my laptop is not connecting to the only network in my home and I can connect to all other wireless networks around.Also there is no problem with the router/modem coz all my room mates can connect and access internet wireless and also through Ethernet.Even I'm able to connect to the home network using Ethernet but not wireless. Strange but true!
[code]...
connect my partner's laptop to my wireless network?
The router is a Sagem provided by my ISP (Sky). The wireless connection works fine on my MacBook, and various other devices connect no problem with the security key.
However, his laptop (Windows Vista) will not connect wirelessly. After entering the password, it says it can't connect because it 'times out' (we are obviously entering the password immediately with no delay). It connects fine with an ethernet cable. It will also connect to an unsecured wireless network we can pick up.
The security setup is WPA-PSK with TKIP encryption, and we've made sure he is using these settings.
If it might be important, he has just moved here, and previously his laptop was connected to another Sky router with no problems.
trying to get an IP address from a public wireless network. I am trying to connect to the wireless network here and I get good signal, but it says, that my access has "Limited Connectivity". I then tried to see why my laptop could not access the system and ran "ipconfig/all" in the command prompt. I pasted the results below. I don't know a ton about computers and why my computer will not get a correct IP address (it sends back that the IP address is 169.254.44.160 as opposed to a 10.xxx.xxx.x that the network should be passing out).
Pasted text from ipconfig/all script
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:Usersxxxxx>ipconfig/all
[code]...
I tried to set up an ad hoc access point on my laptop, but it won't connect to the network I made. I'm using xp sp3.
View 2 Replies View RelatedI recently set up a VPN on my home computer. I am wondering if it is possible for me to connect to the internet via the VPN without also being connected to the internet via my home wireless network? Right now, whenever I disconnect from my home wireless network, my connection to the VPN will also cut off. This is a problem because should my connection via the VPN ever be interrupted, my home wireless connection would then "take over" the connection, and the eb sites I'm visiting would then be able to see my real IP address, which makes having a VPN pointless. I'd like to have it so that if my VPN connection is interrupted, I will simply not have internet until the VPN connection comes back.
I am running Windows 7.
I'm trying to connect my XP laptop to a home wireless network and I keep getting the following error once I enter in the passcode provided by my ISP:The network passcode needs to be 40bits or 104bits depending on your network configuration. This can be entered as 5 or 13 ascii characters or 10 or 26 hexadecimal characters.I have an iphone, 3 ipads, one windows 7 pc and a mac connected to the network with no problems. The password provided by the ISP is 25 characters (letters and numbers). I would hate to have to change the password on all my devices for one Windows XP laptop. I've called Netgear who make the wireless router and they said the only solution was to change the password for all devices.
View 2 Replies View Relatedi have a laptop running Vista which will connect to wireless network, but will not connect to internet. I have tried connecting direct to router and also deleting wireless connection & reinstalling with no luck. I can however use a mobile broadband usb dongle and connect to the internet with no problem - appears to be a problem with connecting via something other than mobile broadband?
View 1 Replies View RelatedI have a wireless network at home but my laptop does not connect to it. The network works as my iPhone connects to it az well as my PS3. The laptop finds the network and has full bars for connectivity but it is only on a local network. I don't have a P.C in the home, the only time I can go online is when the laptop is plugged in. My laptop operates with vista.
View 11 Replies View RelatedI am on the Verizon wireless router connected to my laptop and the xbox wired to laptop. I have another wireless router that i want to connect because the main router is in the basement I am on the second floor. How do I connect the xbox to the 2nd router wired?
View 1 Replies View RelatedBasically, my laptop won't connect to my wireless network, it just stopped connecting yesterday for no apparent reason, the wifi works with my phones and other laptop but not my laptop. I restarted my router, laptop did a system restore and factory restore but no luck. here are specs from ipcongif
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Usersdonnie>ipconfig/all
Windows IP Configuration[code].....
We have printers connected to the network, but I need a standalone printer connected to my workstation due to the confidential nature of some of my printing.I chose a small wireless printer as I already am being strangled with wires and cables.I went thru the wireless installation, and was told to connect PC to printer via USB.I finally got a connection, but not the one I wanted. We also have a wireless router, but connecting to itI got message saying "a connection was made but your PC is not connected to your printer".
View 5 Replies View Related