I have a Linksys WRVA4400N router in my home office that I access my internet with throughout my house. I also have a Linksys WET200 Bridge that I want to use but can’t get them configured together. The Tech support folks keep shifting me back and forth and I’m about the throw my hands in the air. I get to the Advance Configuration setup for the WET200 and when I place the configuration URL 192.168.1.226 I get nothing. I can get to my router adjustments just unsure how to get the WET200 setting entered.
I've just purchased 2 WET200 wireless bridges for our organisation, with the intention of using them to create a wireless bridge between 2 buildings.I've followed this guide here: url...and I'm unable to configure any kind of security other than WEP. More disconcertingly, the foot of that guide states:WET200 only supports WEP for the Wireless Security."Surely this can't be the case? All the marketing blurb states clearly that the WET200 supports WPA2, and I would have thought WPA2 was a given for any wireless product sold today, especially a business grade product. Have I misunderstood what this device can do?
I'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails.
after reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
I have a new WET200 wireless bridge and cannot authenticate to our WPA2 EAP-TLS freeradius server. Here are the steps that I have taken so far:
1. Renamed my pkcs12 client certificate to .pfx extension and imported it into the WET200.
2. Used the client certificate import password as the "Private Key Password"
3. Typed in the client "Login Name"
The freeradius server recognizes the WET200 with the entered credentials but will not authenticate. The freeradius debug log gives the following error:
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! WARNING: !! EAP session for state 0x3e833be03884222b... did not finish! WARNING: !! Please read [URL] WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Normally, with other wireless devices the CA (ceritificate authority) certificate needs to be installed to the client as well as the pkcs12 client certificate? Is there a way to place a CA and client certificate into the WET200?What is the proper method to install certificates into the WET200 for FreeRadius EPA-TLS authentication?
I just purchased a WET200 wireless bridge. After trying a very long password for an enterprise certificate the bridge restarted and I have not been able to contact the device with the default 192.168.1.226 ip address. I have tried performing a reset even by holding the reset button in for a minute. The bridge will not ping either. I do have a power light and the wireless light flashes and the Ethernet port lights function when plugged into my laptop.
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
I'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX (WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I have two separate offices in the same building that I'm trying to connect. They are physically far apart so I cannot connect them wirelessly. I have had an ethernet cable run from the main office to the second office and physically connected it to a WET200. I can see the WET200 on my router in the main office. In the second office, I want clients to be able to come in and connect wirelessly to the WET200 which will then connect them to my router and internet connection. The WET200 is the correct device for this?
I am completely new to wireless networking and know next to nothing. I own an apartment on a complex abroad and they have recently had wireless internet installed. There are some areas of the complex where the signal is very poor.
I have some Cisco small business WET200 ethernet bridging units and was wondering if these would be suitable to boost the signal in these Black spots. How to set this up or any suitable products to over come this problem.
I've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP. I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
WET200 connected to wireless AP WRT54G (192.168.23.3) WET200 IP address = 192.168.23.8 Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
I can configure the WET200 via the laptop, but not able to see anything across the bridge?
I decided to upgrade the firmware in my WET200 so downloaded the latest firmware v1.0.10-ESTI filename WET200-ETSI_v1.0.10_200802_fw.img.Update seemed to go well, and the message came up rebooting please wait.Waited about 5 minutes whilst the message stayed the same, decided to try and close my explorer window and connect again, nothing happened.Tried to reset the unit by holding in the reset butting again nothing seemed to happen. The unit had been set up with the ip 192.168.113.4 before the upgrade but this is now unreachable, also tried the default of 192. 168.1 .226. Anything I can do/try to restore my unit, or did the update brick it?
I need setting up vpn connection between my office network and home computer that runs Ubuntu linux with vpnc as a client. What I did is I went to router's management webinterface -> VPN->IPSec VPN-> then made a new connection (named yfd-vpn). I understand it will be a group name in client settings.local group setup was prefilled for me and it wasLocal Security Gateway Type: "IP only"IP address: xxx.xxx.47.88 Remote Group SetupRemote Security Gateway Type: AnyRemote Security Group Type: IP addressIP Address: zzz.zzz.zzz.137 ###this is my home router's LAN IP address. I am not sure if it should be put here. Maybe WAN address or LAN address on VPN host site with a different network parameters?IPSec setupPhase 1 (left unchanged) Phase 2.
I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
I have a Comcast Modem, which connects to the internet port of a simple 4 port switch (useless now due to lack of a second ip address as of recent), which goes out to the Internet/WAN port of a Cisco Router, which from one of the ports goes out to the Internet/WAN port of a Linksys Router.
I have a PC connected to each router, and my question is, How do I set up the network so that I am able to host a web/game server on the PC connected to the Linksys that's accessible over the internet?
I just replaced my old rv042 with the v3 and updated firmware to 4.0.4.02. i am looking for the MTU setting but i can't find it anywhere. Where that can be found?
I have a problem setting up a VPN between a local office and a head office some distance away.Here at our local office, we have a Cisco WRVS4400N Small Business device.At the head office they have a Cisco ASA Device.We need to set up a point-to-point VPN and I have no idea how to do this with these devices.To make matters worse, the resource I have at the other end in an unknown entity who also does not seem to have much experience with this.Is there any type of step-by-step guide to such a configuration?
Looking for assistance in setting up a VPN Connection on a RV120w.Trying to establish VPN with Android tablets utilizing Anyconnect.I currently utilize IPsec connections into RV120w without issues from desktops/laptops. (I am not real familiar with certificate based connection, and how to export from RV120w and import into Android)
My network to use a RV042 router. It is connected to my cable modem and working well. I may add a DSL connection later in the month as a backup. All I really want to do now is setup my PPTP VPN connection. I have not been able to find a guide so I will assume it isn't that bad. I set up 2 accounts in the VPN-PPTP Server screen. Built my connection on my android phone and voila nothing works. So I tried to disable the "Block WAN requests". I tried port forwarding the VPN to 192.168.1.1 (address of the router) and no luck. AT this point I am stuck. I know my infrastructure is right because from outside the network I can [URL] and see my router configuration. Now if I could just get a simple PPTP connection
I am thinking about buying one of the 2 routers i have listed above. I have some concerns though.
First off what are the MAJOR differences between the two? (they look the same to me)
Do they both contain PPTP and is it simple to configure? Do i need any kind of special client software? Can i use my iphone and ipad to connect to the vpn server. Is there a minium download/upload speed to have a vpn sever?
I recently signed up for Centurylink Prism TV and internet, they use a Cisco DDR2200 (modem+wireless router combo) which I've come to realize is only a "g" router, so I purchased a cheap Belkin N150 (which I intend to use as my main router). I've turned the wireless function off on the Cisco and have an ethernet cable running from a LAN port on the Cisco to the internet port on the Belkin.
The issue I'm having is how do I set up the IP addresses/DHCP servers for both routers? By default, the Cisco's IP address is 192.168.1.254 (I know, weird right?) with a DHCP range of 192.168.1.63 - 192.168.1.253. Whereas the Belkin's IP address is 192.168.2.1 . I guess I'm sort of at a loss on how to set this up to optimize my network.
we have bought 2 Draytek 2830 Routers for our 2 businesses that are in different locations. We are looking at setting up a VPN between them and wanted to do it similar to the following:
http:[url].....
The thing the "Dial IN" site has a static IP from the ISP but the "Dial Out" site has a dynamic IP.what the best approach to take with this would be as I guess the link between the routers wouldn't work if the address kept changing?
Is there documentation on setting the RV042G to Router Mode and what that changes to it's topography? The manual simply tells us to click the button to change the mode?!?!? A 4th grader could figure that out - but what does it do to the unit? Does it basically become a glorified switch with an internet connection? Can the 2nd WAN port be used as a switch node?
We bought a RV220W in order to get a VPN in our Small Business. The RV220W will only be used to let clients connect to it and not a tunnel between another VPN box.We could use QuickVPN, but it won't be working in our case, because in order to use QuickVPN, the router wants to change its IP 10.x.y.1. Because we have multiple servers/services that are using a static IP, it would be quite painful to change the subnet. Therefore, we would like to stay on the same subnet and change it in worst case scenario only. This is why QuickVPN is not an option here.We could use SSL VPN, but most of our clients who will connect to the VPN are using Windows 7 x64. I have tried the Windows 7 x64 fix told in the latest firmware release notes, but I can't get it to work on my computer, which is a Win7 x64. It might still be broken. Many of them are not very tech-savyy, so I can't tell them to use a virtual machine to connect.We want a secure connection, therefore IPSec is better than PPTP. I've been trying to setup IPSec for the past hours but I can't get it working. At first, I wanted to use an SSL certificate, but having no luck with this, I switched to a Pre-shared Key (PSK) in order to get things simpler. Eventually I would like to use an SSL certificate, however I would like to get PSK working first to confirm that the IPSec connection is working.
I have attached with this post, screenshots of the IKE and VPN Policies. I have used the VPN Wizard in order to complete these fields. The local identifier is the WAN DynDNS FQDN. However, as for the remote FQDN, there should be none really, because clients are connecting to it, so the RV220W won't know in advance who's connecting and from where. I have read that when using the Responder type, the remote settings should not matter. Also, the PSK is 25 caracters long.After setting the RV220W up, I have set up a L2TP/IPSec VPN connection on my Windows 7. I have set up the connection to connect to the DynDNS address and set up the PSK in the Advanced settings. After I typed my IPSec username and password to connect (which was created in the IPSec users section), Windows tries to connect and times out :
Error 789 : The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer.
At the same time on the RV220W, this error shows up in the logs :
2012-08-26 23:45:24: [rv220w][IKE] ERROR: Could not find configuration for 24.54.xx.xx[500]
I can't figure out what I am doing wrong. I've read the Administration manual quite a few times and it seems that I have followed everything by the book.I have tried to enable/disable my Windows firewall, but did not get any luck. The RV220W is located at a remote office, to make sure that I can connect from the outside, before you think that I'm trying to connect to the outside, from the inside I have changed few settings in the IKE policy to try to make it work. Settings such as the Exchange Mode, because I've read that the Aggressive mode had issues. At this moment, the settings are back to default, once the wizard has been run. I'm thinking about setting a PPTP to confirm that this works, then move up to IPSec PSK, then to IPSec SSL Certificate.
Looking for setting up the RV180 behind the ActionTec MI424WR-GEN2. At the same time I want to be able to VPN into the network and be able to access objects.
Ideal setup: Verizon ActionTec modem is primary network (192.168.1.x) RV180 is secondary network (192.168.2.x) VPN to 192.168.2.x network from remote locations (client-to-gateway)
I've tried asking from Cisco Support and was given the "we don't suppor that configuration" line. They want me to put it in front of the ActionTec FiOS modem/router in which case then Verizon will provide zero support for anything.Now, to add an extra twist, I do have STBs (Set-Top Boxes) connected to the Verizon FiOS modem/router but nothing special (i.e. no DVR or any stuff like that). How to get this thing up and running so that I can have remote folks VPN into the network? We work with data that needs to remain encrypted during transmission, hence the VPN.I have forwarded ports 443 (TCP), 60443 (TCP), 500 (UDP) and 4500 (UDP) to the WAN IP of the RV180. Network objects behind the RV180 cannot get past the router (it's in router, not gateway mode). The RV180 can ping objects both on the WAN and LAN side, so it seems that the RV180 is the problem child.
Initial setup with RV220W completed without difficulty,Need to set up static IP for one of the machines in the LAN (not static IP for WAN),I presume I use the static DHCP option, which allows me to select a particular IP for the machine I select based on it's MAC,1. My confusion stems from the manual stating that "the IP address that you pick should be outside the DHCP address range specified on the Networking> LAN(local network)>IPV4(local network)page".,Does that mean that the range on the IPV4 local network page should be modified to exclude the IP address that I want to use for the static IP..e.g. change the range from 1-255 to 1-200 and then use an IP of XXX.XXX.X.201 for instanceor does that mean that as soon as I choose an IP on the Static DHCP page, that if will reserved for use only on that machine and not used for another machine on the LAN, without me having to do something else to exclude it's use (i.e. does reserving a static IP automatically remove it from the range of IPs available to other machines)If I simply set a static IP on the local machine by going to "change network adapter" settings, what's the liklihood that the router might use the same IP on another machine.
have a Cisco RV120W and I need setup a Quick VPN user, however i can't enable this user.I have Remote Management enable, access type All Ip Address and port number 443.
I spoke with the Comcast gateway support team and they changed my SMC router to the straight gateway/bridge option. If I plug directly from my laptop to the SMC, I have internet connectivity. So I know that aspect is working. I have a Cisco RV220W router that I want to be between the internet/SMC gateway and my network. For the life of me, I cannot get the internet connectivity to pass through to the router. I've done the proper power on order numerous times. Tried variations just for the heck of it. And nothing. Am I missing a step? If I do the "wizard" on the router, it basically tells me it sees no gateway even available even though it is clearly there and plugged into the WAN port. I don't see any option in the router settings for me to specify like the DHCP server I should be reaching out (if there even is one). My understanding is I shouldn't need to as the router should just recognize it. Should I be using a static IP instead?
We are setting up a vpn between a cisco RV082 and a checkpoint device. From the Cisco device we have set up (as remote IP) the public IP 85.xxx.xxx.xxx but when we try to start the tunnel the VPN log (from RV082) report the error "INVALID_ID_INFORMATION" as described below.
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: sending encrypted notification INVALID_ID_INFORMATION to 85.xxx.xxx.xxx:500 Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: we require peer to have ID '85.xxx.xxx.xxx', but peer declares '10.yy.yy.yyy'
[code]....
The IP 10.yy.yy.yyy. reported in the log is the natted ip of the Checkpoint device.
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
