Draytek 2830 Routers - Setting Up LAN To LAN VPN?
Apr 11, 2013
we have bought 2 Draytek 2830 Routers for our 2 businesses that are in different locations. We are looking at setting up a VPN between them and wanted to do it similar to the following:
http:[url].....
The thing the "Dial IN" site has a static IP from the ISP but the "Dial Out" site has a dynamic IP.what the best approach to take with this would be as I guess the link between the routers wouldn't work if the address kept changing?
View 2 Replies
ADVERTISEMENT
Sep 18, 2012
Any experience with IP Routing on Draytek routers?We have a 2830 and I'm trying to set it up like the following: [code]
Now a server in VLAN 2 with address x.x.x.77 can ping x.x.x.74, but I can't access any of it's services (Apache, SSH etc) from the internet (testing through my phone and other people).I've removed the IPs from the NAT pool in the WAN settings, setup LAN2 for IP routing and put it into the second VLAN, but apart from that not done much else.
View 3 Replies
View Related
Jun 26, 2011
My company is setting up a small branch in Scotland (the main office is in Bristol)All we need one desktop, one laptop, a printer and we will be using a DraytekVgn router, and a small switch.We need VPN to this office to set up an inhouse application.How would I set this up with minimal configuration.......ie...Does BT send a router/modem with the set up..Is there anything inside the router configuration that has to be changed.(I know PPTP etc has to be enabled).Do I use the same vpn external ip address we use for our other 2 branches....Can I change the IP Address of the router from 192.168.1.1........to say 192.168.100.1.
View 6 Replies
View Related
Mar 26, 2012
I've recently installed a Cisco ASA with a NAT'd configuration, I'm in the final stages and would like to configure a lan to lan VPN to a Draytek box and that unfortunately isn't going well and having spent almost two days on it am starting to wonder if it will actually work. I can get it to connect but no data seems to be transmitted between the two.
Site A on the range 10.0.0.0 has the ASA and Site B is on the 192.168.16.0 and is a Draytek 2930.
Below is the ASA config created with the lan to lan wizard:
route outside 0.0.0.0 0.0.0.0 193.164.x
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00(code)
View 1 Replies
View Related
Jun 27, 2011
We're trying to establish a "simple" vpn tunnel between a cisco 800 and a draytek 2910, situation:
LAN (192.168.2.0 ) --cisco800 ----- internet ------ draytek ----LAN (192.168.20.0 )
WAN-ports , internet access on both sides are working fine.vpn configuration part cisco:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[code]....
What can be wrong: other protocol? something with pfs? diffy hellman group: i heart draytek used 1 and cisco 2?debugging on the cisco site keeps on ginving the error message:
entry number 487 : CRYPTO-4-IKMP_BAD_MESSAGE
IKE message from x.x.x.x failed its sanity check or is malformed
timestamp: 4002880
View 5 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Dec 17, 2011
I have recently changed my Router to a Draytek Vigor 2830N from the standard O2 broadband router. When I swap them out I get no internet access via the main PC that is connected via ethernet. However I can access internet via WLAN on any other device. here are the ipconfig details for before and after swap (same)
View 3 Replies
View Related
Apr 20, 2011
I have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0
*Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10
*Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002)
*Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
View 8 Replies
View Related
Jul 14, 2011
I am currently using a Draytek 2820 at work and I am needing to port forward port 3333 to two different computers at the same time
View 9 Replies
View Related
Jun 14, 2011
I'm having some rather odd issues with my wireless connectivity. Running a draytek 2830n router. The wireless connection drops out at random sometimes, at other times it connects (shows full reception) but does allow any kind of internet connection. Plugging in by lan cable allows normal function.I have no clue whats going on but I did just notice that shutting down one of the laptops connected to the network (Dell lx502) appears to have solved the problem for the moment. I've not had a chance to test this as a long term solution. However I believe this is the only laptop with a dual band wifi card.This problem was also occurring on our previous router, a draytek 2820vn but the symptoms were a bit different and this laptop was not there at the time.Is it possible for one machine to knock out an entire wireless network? The other change I made yesterday was to activate the bind ip to mac function on the router for our new NAS as I was messing around with ftp configurations.
View 1 Replies
View Related
Jun 19, 2011
my local site has Cisco 2811 router connecting locally to ASA 5520. Remote site A has Draytek Vigor2950. I have working vpn between local subnet 10.0.0.0/24 and remote site A 10.100.6.0/24. I have remote sites B (10.100.7.0/24) and C (10.100.8.0/24). I would like to route traffic from local site to remote sites B and C via the local-to-remote A vpn. On Draytek routers B and C, I have added to subnet 10.0.0.0/24 to the remote network profile list. On local router, I route traffic for subnets 10.100.7.x and 10.100.8.x to the ASA. On ASA I have added these subnets to the profile for local-to-remoteA vpn.But the vpn will not establish when I attempt to ping from local to remote B or C.
View 5 Replies
View Related
Aug 28, 2012
I have a Comcast Modem, which connects to the internet port of a simple 4 port switch (useless now due to lack of a second ip address as of recent), which goes out to the Internet/WAN port of a Cisco Router, which from one of the ports goes out to the Internet/WAN port of a Linksys Router.
I have a PC connected to each router, and my question is, How do I set up the network so that I am able to host a web/game server on the PC connected to the Linksys that's accessible over the internet?
View 1 Replies
View Related
Apr 19, 2011
I have managed to get the tunnel up and working and we are sending data via the tunnel from our Cisco VPN router to the Draytek and onto the clients server. (they , the client, have acknowledged that they are recieving and sending packets back to us).But, we never see any returning packets at our VPN tunnel endpoint. When we send I see the encrypted packet count go up , but the packet decrypt remains at zero, this is using show crypto ipsec sa | begin x.x.x.x.
We do have other working VPN solutions, but this is the first connecting to a Draytek. The ACL's are matching, and they have NAT turned off. The routing is fine or else the tunnel would not come up as are all the tunnel parameters, else our packets would not arrive at their server.
View 1 Replies
View Related
Nov 30, 2012
I recently signed up for Centurylink Prism TV and internet, they use a Cisco DDR2200 (modem+wireless router combo) which I've come to realize is only a "g" router, so I purchased a cheap Belkin N150 (which I intend to use as my main router). I've turned the wireless function off on the Cisco and have an ethernet cable running from a LAN port on the Cisco to the internet port on the Belkin.
The issue I'm having is how do I set up the IP addresses/DHCP servers for both routers? By default, the Cisco's IP address is 192.168.1.254 (I know, weird right?) with a DHCP range of 192.168.1.63 - 192.168.1.253. Whereas the Belkin's IP address is 192.168.2.1 . I guess I'm sort of at a loss on how to set this up to optimize my network.
View 5 Replies
View Related
Apr 28, 2012
I need setting up vpn connection between my office network and home computer that runs Ubuntu linux with vpnc as a client. What I did is I went to router's management webinterface -> VPN->IPSec VPN-> then made a new connection (named yfd-vpn). I understand it will be a group name in client settings.local group setup was prefilled for me and it wasLocal Security Gateway Type: "IP only"IP address: xxx.xxx.47.88 Remote Group SetupRemote Security Gateway Type: AnyRemote Security Group Type: IP addressIP Address: zzz.zzz.zzz.137 ###this is my home router's LAN IP address. I am not sure if it should be put here. Maybe WAN address or LAN address on VPN host site with a different network parameters?IPSec setupPhase 1 (left unchanged) Phase 2.
View 3 Replies
View Related
Mar 3, 2013
I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
View 2 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
Nov 23, 2012
I'm trying to resolve an issue I've been having with Google Chrome. I've found a possible fix but i need to confirm the MTU settings on my router and was unable to locate the setting using the web interface for the router.
View 3 Replies
View Related
Nov 8, 2012
Are Belkin routers compatible with VPN? Is there a VPN pass through setting for the N600?
View 3 Replies
View Related
Dec 7, 2012
Can I set up WPA2 on my Belkin N router F5D8236-4 V3 for a Macintosh running OS10.6.8? And for another machine running OS 10.8? The manual seems to talk about WPA2 for Windows and WEP for Macs, but I can't tell if this is because there are some issues before using the protocols.
View 1 Replies
View Related
May 23, 2012
I have a Linksys WRVA4400N router in my home office that I access my internet with throughout my house. I also have a Linksys WET200 Bridge that I want to use but can’t get them configured together. The Tech support folks keep shifting me back and forth and I’m about the throw my hands in the air. I get to the Advance Configuration setup for the WET200 and when I place the configuration URL 192.168.1.226 I get nothing. I can get to my router adjustments just unsure how to get the WET200 setting entered.
View 1 Replies
View Related
Oct 10, 2011
I just replaced my old rv042 with the v3 and updated firmware to 4.0.4.02. i am looking for the MTU setting but i can't find it anywhere. Where that can be found?
View 2 Replies
View Related
Apr 22, 2012
I have a problem setting up a VPN between a local office and a head office some distance away.Here at our local office, we have a Cisco WRVS4400N Small Business device.At the head office they have a Cisco ASA Device.We need to set up a point-to-point VPN and I have no idea how to do this with these devices.To make matters worse, the resource I have at the other end in an unknown entity who also does not seem to have much experience with this.Is there any type of step-by-step guide to such a configuration?
View 5 Replies
View Related
Oct 12, 2011
Looking for assistance in setting up a VPN Connection on a RV120w.Trying to establish VPN with Android tablets utilizing Anyconnect.I currently utilize IPsec connections into RV120w without issues from desktops/laptops. (I am not real familiar with certificate based connection, and how to export from RV120w and import into Android)
View 2 Replies
View Related
Sep 21, 2012
My network to use a RV042 router. It is connected to my cable modem and working well. I may add a DSL connection later in the month as a backup. All I really want to do now is setup my PPTP VPN connection. I have not been able to find a guide so I will assume it isn't that bad. I set up 2 accounts in the VPN-PPTP Server screen. Built my connection on my android phone and voila nothing works. So I tried to disable the "Block WAN requests". I tried port forwarding the VPN to 192.168.1.1 (address of the router) and no luck. AT this point I am stuck. I know my infrastructure is right because from outside the network I can [URL] and see my router configuration. Now if I could just get a simple PPTP connection
View 7 Replies
View Related
Feb 3, 2013
I am thinking about buying one of the 2 routers i have listed above. I have some concerns though.
First off what are the MAJOR differences between the two? (they look the same to me)
Do they both contain PPTP and is it simple to configure? Do i need any kind of special client software? Can i use my iphone and ipad to connect to the vpn server. Is there a minium download/upload speed to have a vpn sever?
View 6 Replies
View Related
May 31, 2011
I have an operating router with no problems, but I need a secure network.on setting a password for my TP-Link model TL-WR941ND router
View 3 Replies
View Related
Jun 30, 2011
If you have two wireless routers on the same private network. On configuring the second router's password and SSID I know the second wireless routers DHCP must be turned off.Can you explain step by step on configuring the second wireless. Must the second wireless be connected to the internet. If yes, how? Must I take the first wireless router off the modem and connect it to the second wireless router for internet connection. (Problem with that is connection from the ISP)
View 2 Replies
View Related
Jun 8, 2011
I have large bunglow with 2floors,I would like to have a wireless internet setup in bunglow using 3g usb modem type of internet connection.Advise which router to be used so that I can get good wifi connectivity all over the place so minimum 4 people can use it simaltaneously.
View 1 Replies
View Related
Jan 22, 2011
I am trying to connect my xbox360 to my belkin surf n300 router via ethernet cable and my xbox360 cant recognize or get onto my network. i have manually entered the ip address the submask and gateway numbers, idk if they are 100% correct
View 1 Replies
View Related
Jun 13, 2012
I have a 4-port Netgear modem/router (DG834), and need to distribute its Internet connection according to the following criteria:
1.There are 11 access points (3 wired, 8 wireless) across 4 floors of a building - all cabling is from a central point, which will connect through a switch.Cat 5e cabling is in place.
2.The wireless points need Power over Ethernet connections
3.The 4 router ports serve 2 PC's and a printer in an office, the fourth being the connection to the switch.
4.There must be network separation so that:
- all points have Internet access
- there are three separate groups - one for the office, one for staff (wired) and one for guests (the wireless points), the purpose being to ensure that no user in one group can access any user's device in the other 2 groups. I'm assuming VLAN is the method for this.
5.Traffic on the network is likely to be fairly low casual use of the wireless ports, the office PC's only being used for Internet access and email no transactional systems, large databases or other resource / network-intensive functions.
1.Both the Netgear FS726TP and GS724TP look as if they will do what I want, using WNAP210 wireless access points. Could I achieve the same outcome with 2 x GS108PE switches? Any other hardware recommendations?
2.Do I need any additional hardware?
3.Are there any other considerations I have not thought of?
View 10 Replies
View Related
Jun 8, 2011
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
View 2 Replies
View Related
Mar 22, 2011
I am migrating an a group of workstations that run a fire system from one software to another. The current workstations run the following info:123.123.123.xxx 255.255.255.0The new workstations run:100.100.100.xxx 255.255.255.0There is a central switch location using a GE-DSG-244 Layer 2+ Managed switch. There are two remote location using GE-DS-82 Managed Switches.The two networks must remain isolated, yet use the same fiber communications. The central switch connects to the two location using MM Fiber. From my research I believe I need to use the 802.1q standard to allow port trunking between the two switches.
View 7 Replies
View Related
