Change O2 Broadband Modem To Draytek Vigor

Dec 17, 2011

I have recently changed my Router to a Draytek Vigor 2830N from the standard O2 broadband router. When I swap them out I get no internet access via the main PC that is connected via ethernet. However I can access internet via WLAN on any other device. here are the ipconfig details for before and after swap (same)

View 3 Replies


ADVERTISEMENT

Cisco VPN :: 7100 VPN Router To Vigor Draytek 2820 VPN Router?

Apr 19, 2011

I have managed to get the tunnel up and working and we are sending data via the tunnel from our Cisco VPN router to the Draytek and onto the clients server. (they , the client, have acknowledged that they are recieving and sending packets back to us).But, we never see any returning packets at our VPN tunnel endpoint. When we send I see the  encrypted packet count go up , but the packet decrypt remains at zero, this is using show crypto ipsec sa | begin  x.x.x.x.
 
We do have other working VPN solutions, but this is the first connecting to a Draytek.  The ACL's are matching, and they have NAT turned off. The routing is fine or else the tunnel would not come up as are all the tunnel parameters, else our packets would not arrive at their server.

View 1 Replies View Related

Linksys Wireless Router :: Adding WRTG54 To Vigor ADSL Modem?

Sep 27, 2012

We have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
 
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
 
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
 
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
 
What do we need to do at the Linksys end to get wireless working again?

View 9 Replies View Related

Broadband :: Change Setting From Telstraclear To Broadband?

Mar 2, 2011

i need to change my computer setting so it connects to a broadband modem?

View 1 Replies View Related

Broadband :: Connect A Modem / Router To A Cable Modem?

Feb 7, 2012

I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.

View 10 Replies View Related

Broadband :: How To Change Ping Response

Apr 22, 2011

I want to change ping latency because my application cannot run in 1ms or 35ms it will work on 600ms to 1500ms due to in VSAT minimum response time latency is 600ms to 1500ms.for i want to change in my 2003 server reponse letancy time.and we are use online accounting software and connecting through ftp server.kindly do the need full how to change response time frame in windows

View 2 Replies View Related

Broadband :: Change Route Of Connecting An IP?

Sep 22, 2011

I play a game called Unreal tournament 2k4 in online. I am from Bangladesh a small country from south asia. I used to get 150 ping in a Japanese server. But 2 weeks ago my ping suddenly rise. Now its around 268-320 in same server. But i have 160 ping in another Japanese server. So i used trace-route option from avast IS to check the route of my connection.I found out that the server i am having high ping connects through Italy then to Japanese server. But the server i have low ping goes to Singapore then to Japan.My question is can i change the route of my connection so my first server doesn't take the route of Italy?

View 1 Replies View Related

Broadband :: Cannot Surf The Web Nor Change The Homepage?

May 16, 2011

I have windows xp on sony laptop. I use dial-up, cricket broadband and wifi. When on wifi I can surf. I cant cannot get off the homepage nor change it when I connect to my cricket broadband. Cant surf because it keeps going to Crickets homepage and when closing or opening another window, it will revert back to cricket and it keeps changing homepage

View 1 Replies View Related

Broadband :: Suddenly Cannot Change IP Address Anymore

Jan 6, 2011

I have not changed ISPs.Yes, I have contacted my ISP about the matter, but, as expected, to no avail.No, I am not using a new modem.To my knowledge, I have made no network related changes whatsoever since the problem arose.This will certainly raise the question "Why do you need to change your IP, anyway?" Well, to be perfectly honest, the game site that I frequent has a newly implemented hacking detection system that temporarily bans a user from entering all game rooms if it detects any suspicious activity on the user's part. This system is quite fallible and hence results in many unwarranted bans daily. In the event that I am unlucky enough to fall victim to the ban hammer, I simply change my IP and continue playing.

View 8 Replies View Related

Linksys Wireless Router :: Vigor 120 Bridged With EA4500 Extremely Slow Connection

Feb 1, 2013

I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
 
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.

View 9 Replies View Related

Broadband - The Modem Is Already In Use

Jun 8, 2012

Im having problems connecting my broadband to the internet, when I press the "Connect" button here is what pops up;

Quote:

The modem (or other connecting device) is already in use or is not configured properly.I've tried doing;

1. Tried installing the software+driver to other laptops and it works fine.

2. Tried changing different modems and installed the required driver but ends up not able press the "Connect" button at all.

3. Tried Uninstall/Reinstall the software/Driver.

4. Disable/Enable driver from Device Manager.

5. Tried Doing a Recovery system but fortunately the recovery system goes as far back the first time I've tried installing this device.

6. Tried disabling Anti-Virus

7. Tried installing old version of Mobile Partner but it seems like it didnt detect the device and a pop-ups saying "Failed to find Port" when installing Mobile Partner 2.3 .This laptop used this broadband before 1-2 months ago.

View 4 Replies View Related

Broadband :: How To Speed Up Usb Modem

Apr 14, 2011

i want to speed up utorrent and idm downloading speed and i am using mblaze usb modem(mts)

View 1 Replies View Related

Broadband :: PC Won't See Netgear Modem

Apr 18, 2011

I am hard wiring a Netgear wireless modem DG834G to the LAN connection on my PC. The modem lights up, the internet light flashes then goes green and the connection to the PC is lit. My PC wont see the modem - when I type 192.168.0.1 it cannot access the Netgear setup page. I have tried swapping the cable and even bought a PCI Lan card and installed it but the modem wont work in either port? I've had the modem checked out and it works fine it's just something in my PC stopping it from seeing the Modem. At present I have a USB modem hard wired which works fine. I unplug this when trying to setup the NEtgear modem...

View 6 Replies View Related

Broadband :: Use Wireless Modem And LAN Together?

Mar 4, 2011

I have a Lan connection operating through a DSL. I also have a Wireless 3G modem. can I use both at the same time to boost my connection speed?

View 1 Replies View Related

Broadband :: Connecting A Modem To Router?

Aug 23, 2011

I HAVE AN I BALL BATON iB lr6111a and i need to connect the same to a router but it has only one rj45 port since the router dont have a modem how can i connect it to a modem with only one port.

View 1 Replies View Related

Broadband :: How To Enable Dhcp On Usb Modem

Apr 14, 2011

i am using mblaze usb modem and i want to increase the speed

View 1 Replies View Related

How Secure Is A Broadband Modem Like Version 4g

Oct 13, 2012

How secure is a broadband modem like version 4g lte hooked to a computer rather than hooked to wireless router

View 3 Replies View Related

Broadband Modem Is Working But Cannot Get Online

Apr 29, 2012

I don't think it's my PC, because I tried using the Ethernet cord on my laptop, and got the same error "limited or no connectivity..." When I try to troubleshoot on my PC, it says the modem is fine. All the lights are green on the modem. I did notice that I have an IP address, but no Gateway Address. Also, I'm sending few packets, but receiving even fewer.Is it safe to say that this is a modem issue? Or something else? Is there anything that can be done? -resetting the modem did not work.

View 14 Replies View Related

Broadband :: How To Configure Aztech Modem

Mar 30, 2011

I need line settings for manual configuration.becouse seens i change my modem to aztech,i got a slow connection,not like before(good).

View 1 Replies View Related

Broadband :: Ethernet Modem Light Blinking

Jun 14, 2012

HandPunch 3000 Time & Access Device, no Communication over the Ethernet, on the Ethernet Card the red light flashes for 1sec then red & Green for 1sec.

View 1 Replies View Related

Broadband :: Reset PCI Soft Data Modem?

Feb 9, 2011

We recently upgraded to higher speed internet and were to "reset" our modem, which is PCI Soft Data Fax Modem With SmartCP.How does one "reset" their modem?

View 1 Replies View Related

Broadband :: How To Connect Desktop And Laptop In 1 Modem

Jan 7, 2011

connect the desktop and my loptop in one modem

View 1 Replies View Related

Broadband :: How To Block Modem Internet Speed

Jan 5, 2011

i recently opened internet cafe,i have internet connection of 8mbps, and i have 6 computers, and internet speed distributes 8 mbps to per computer, i want to decrease this speed, i want to give 1 mbps to every computer

View 1 Replies View Related

Setup VPN On Draytek Router Using BT As ISP?

Jun 26, 2011

My company is setting up a small branch in Scotland (the main office is in Bristol)All we need one desktop, one laptop, a printer and we will be using a DraytekVgn router, and a small switch.We need VPN to this office to set up an inhouse application.How would I set this up with minimal configuration.......ie...Does BT send a router/modem with the set up..Is there anything inside the router configuration that has to be changed.(I know PPTP etc has to be enabled).Do I use the same vpn external ip address we use for our other 2 branches....Can I change the IP Address of the router from 192.168.1.1........to say 192.168.100.1.

View 6 Replies View Related

Cisco VPN :: ASA Lan To Lan VPN With Draytek 2930

Mar 26, 2012

I've recently installed a Cisco ASA with a NAT'd configuration, I'm in the final stages and would like to configure a lan to lan VPN to a Draytek box and that unfortunately isn't going well and having spent almost two days on it am starting to wonder if it will actually work. I can get it to connect but no data seems to be transmitted between the two.

Site A on the range 10.0.0.0 has the ASA and Site B is on the 192.168.16.0 and is a Draytek 2930.

Below is the ASA config created with the lan to lan wizard:
 
route outside 0.0.0.0 0.0.0.0 193.164.x
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00(code)

View 1 Replies View Related

Can't Change Setting Of Modem

May 30, 2012

I have read many guides about how to forwarding some port in routers, and i did exactly the same as tutorial,after trying many time i just noticed there is something wrong with my router well here the informations.my router model/name UTStarcom AR7RD im using Windows xp SP3 86x my firewall is disable (But i already added the ports i need to open in my firewall)my Upnp are disable in my router well my computer takes a ip from ISP soo i dont need static IP there is no option that let me delete the old useless ports,i searched almost all the sections of my router and i failed to find a thing that let me delete some port.i went to DMZ setting to Active it cuz its the last thing for me to able open some port, i went to DMZ SETTING and tried to enable the check mark for this section i noticed it wont enable, i got no error there just it wont be enable.im watching around its 2 weeks i search any where in different forums and googles.

View 14 Replies View Related

D-Link DIR-655 :: Change Its IP Towards Modem?

Oct 26, 2011

I've searched high and low across the wide web, but I have found no real answer to this problem;Recently, I bought the DIR-655 because the gods of thunder decided to euthanize my old WAP. The original plan was to mate this up with a Tilgin VOOD-modem (modem and router in one; a heap of s**** in my uneducated eyes) in order to make networking within my appartment somewhat easier.

Got it safely indoors, plugged it in as the manual told me, and got it going (my old WAP was also a D-LINK, so the interface was somewhat familiar). Checked cabled connection, worked fine, and I got the wireless-bit to function as well. But then I, or my Xbox 360 to be right on the money, encountered a little problem. As I understand from a little bit of research, I found out that this was a dreaded phenomenon known as

"Moderate NAT"

Before I got the old WAP indoors, I used the onboard router in the TILGIN to do the switching. I used to have this problem back then also, but solved it by opening some of the ports on the modem. Then it switched to "Open NAT", and worked like a charm. Now however, I have ran into a problem I can't dig myself out of. I have tried DMZ, opening numerous ports all the way to the full monty, but I can�t get that NAT to wander into the more acceptable range. And then it became clear that the internet on my laptop was somewhat amputated as well; simple youtube-videos became harder to load (sometimes it actually had to stop for extended streaming!), and this is not acceptable on a 20 mbt DSL-line!

View 8 Replies View Related

Broadband :: Modem Driver For Windows 7 Of Linktop Ct800p?

Jul 31, 2011

modem driver for windows 7 of linktop ct800p

View 2 Replies View Related

Broadband :: Direct Connect Cable Modem To Computer?

Jan 7, 2011

I have a new router (ASUS RT-N10)and It is asking me to direct connect my cable modem to my computer, and then find my MAC address via command prompt, and clone it to the new router.I can get to my command prompt, the problem lies in windows 7 and vista's (or mine) inability to realize that my network card is directly connecting to the modem. (No internet connection available, doesn't think anything is connected). I have tried on multiple machines to try and find my modem's mac address but it simply is not working.I want to know if I can find the mac address through the old router, or what I need to do to have windows 7 recognize I'm directly connecting the modem to the PC.

View 3 Replies View Related

Broadband :: Adsl Modem / Router Mac Changing In Dos Prompt?

Jan 26, 2012

Modem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.

View 1 Replies View Related

Motorola Surfboard SB6120 Modem / Can't Get PC To Connect To Broadband

Jun 22, 2011

I can't get my PC to connect to my broadband. I am running windows 7 64 bit and use the following:

Motorola Surfboard SB6120 modem;
NetGear WGR614 wireless router

I am able to connect with other devices (iPhone, Roku) to my wireless through the wireless router. My computer recognizes the broadband connection, but it won't connect to it. I get two errors when I try to connect:651: the modem has reported an error, and 638: the remote server is not responding in a timely fashion.I have tried connecting the ethernet cable directly to the modem, but I get the same results.Also, I have tried to cycle down the computer, router, then modem and turn them back on in reverse with no change in results.The connection worked until I clicked "disable connection" one day when I had trouble connecting (high traffic i think). Since then, the"home group" I set up originally with the connection wizard disappeared, and it had not been able to connect since then. When I try to connect I click on a small icon in the lower right that says, "not connected, connection available", then I click on the button to connect to broadband and get the errors described above.

View 3 Replies View Related

Broadband :: DSL Modem Connection Giving IP Address Conflict?

Feb 5, 2012

im recieving ip conflict adress error i have an dsl modem and its my individual i ave not share a connection with anyone.and whenever i recieved this error my net works zero

View 1 Replies View Related

Westell 7500 - Can Dsl Router Connect To A Broadband Modem

Sep 11, 2011

can a westell 7500 router/modem dsl from verizon connect to optimum broadband cable?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved