Modem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.
View 1 RepliesI have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
I've finally gone and done it. I phoned up aol and requested my MAC code.With my new ISP ( possibly ZEN ) if I keep my existing netgear router, can I keep my wireless connection settings the same i.e. network name, wep key etc.If, on the other hand I get Zen's router which is pre configured, I would need to set up the wireless again. Could I still use the same network name and wep key, or would I have to chose new ones.
View 3 Replies View RelatedWe are upgrading our dsl to cable. We have a cisco 877 router/dsl modem and windows sbs 2003 r2. May I know how do I change the ip addresses in the router, and how do I add a cable modem to the router?
View 1 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View RelatedI want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies View RelatedI am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
View 2 Replies View RelatedI have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
View 1 Replies View Relatedconfiguring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.
I'm expanding my home network and the adsl modem router supplied by my ISP has just 1 RJ-45 port and 1 usb port (and an RJ-11 for the Internet). I have zeroed in on TP-Link TD-W8901G having 4 RJ-45 ports, 1 USB port, 1 RJ-11 port and also it is a wireless router. Currently I would be connecting the above modem router to my desktop running Linux and using the same ISP with ADSL. Considering a future scenario where I may decide to use another way to connect to the Internet like maybe 3G or Cable, etc (with their separate modems) I was wondering if my same modem router (TD-W8901G) could be used as a standalone router for connecting the devices on my home network. Basically, what I want to know is whether this modem router would be able to share an Internet connection from some other source, other than the one provided through its own RJ-11 (ADSL) source?
View 1 Replies View RelatedI've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
i have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies View Relatedbought a second hand laptop but all previous owners details are still in. they must have been on a dial-up network want to change to broadband,how? also need to sort out wifi.
View 1 Replies View RelatedWe have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
We got a 1921 router that works fine. We ordered Verizon Businss One Static IP ADSL. It came with a Westell Modem that we configured in bridge mode. When we do a test by assigning a static IP to our laptop then hook it up to the Westell it works fine. We can browse the web. Then when we assign a static IP to the Ethernet on our 1921 then connect it to the Westell it doesn't work. We can't ping out from the router to for example 4.2.2.2. From the router we can't even ping the default gateway (on Verizon's side).
View 2 Replies View RelatedI bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedI own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies View Relatedhow do you set up an ethernet port for DHCP with a Belkin ADSl modem with wireless G router, model number F5D7632-4?
View 1 Replies View Relatedi have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
I HAVE AN I BALL BATON iB lr6111a and i need to connect the same to a router but it has only one rj45 port since the router dont have a modem how can i connect it to a modem with only one port.
View 1 Replies View RelatedAt home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies View RelatedRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies View Relatedcan a westell 7500 router/modem dsl from verizon connect to optimum broadband cable?
View 1 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedMy friend changed to TimeWarner cable a while ago. I bought her a netgear wireless switch to have wireless access. She has an old laptop as well with Vista on it, and was trying to connect that to the WiFi. Let her buy the Linksys. Didnt solve the problem and he turned off the wireless security to connect the Vista laptop. That was somewhere July 2011. Since than I have setup MAC filtering to at least have the WiFi not completely open to the public.
View 2 Replies View RelatedI have a Dell XPS 430 desktop and a Netgear DGN2000 modem/router. My ISP is Zen. The router is connected to the PC by an ethernet cable.I have had no problems accessing the internet for years until a couple of days ago when the monitors on the info bar show a triangle with a yellow exclamation mark. The Windows Diagnose and Repair reports - Error 815. The Broadband Network Connection could not be established because the remote server is not responding.My laptop with a wireless connection to the router as no problem connecting so I assume the router is OK.
View 9 Replies View RelatedAt my home I have a Westell 6100 DSL modem connected to a computer.AT&T is the ISP and all filters are installed.I use my home computer via VNC applications from a remote location and I began to notice that the VNC local client session was being lost,,,over and over.It was discovered that the WAN IP was changing over and over and happens about once every 5-10 minutes,,,or so. While I have a dynamic WAN IP from ATT, I would not expect the WAN IP to change as often as 7-8 (or more) times a day. At first I thought it was ATT changing my DYNAMIC WAN IP.But, a review of the Westell log file is reporting lost connection(s),,,,,etc, etc,,,,,etc. over and over.Below is a list of the Westell log information showing several hours of behavior.The Westell diagnotics that were run and the SELF test run as expected.Looks like the DSL modem is going bad, a filter is bad, or the line is going bad and needs to be balanced,,,,etc..
Code:
All Entries
CURRENT MODEM STATUS
DSL Modem Status....... Up
PPP Session Status...... Up
Connection Type......... PPPoE
Time set from............. Local
[code]....
i have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.
View 1 Replies View RelatedRecently i have to change my modem (lightning struck) which of course, done by my ISP worker.The problem is, since then, I've been getting the "DNS lookup failed" error message constantly while using Google Chrome. Or sometimes the "This web page is not available - The connection to [URL] was interrupted".I have to refresh the search once or twice to get to the site, which is very annoying. I tried surfing on my friend's laptop, using the same wireless connection and it seemed to work fine. This problem only occurred on MY laptop.One more thing is, the connection doesn't seem to go wrong because i could play online game with no trouble like lagging or disconnection whatsoever. (Starcraft)
These are the details:
ISP - Streamyx (malaysia)
Broadband - ADSL wireless
Modem - ZyXel p-600 series
Anti-Virus - Trend Micro Titanium Internet Security
Firewall - Windows Firewall