I own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 RepliesRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Every day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies View Relatedi have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedMy desktop recently broke so i bought my first laptop. I have AT&T DSL and i bought a new D-Link DSL-2640B modem/router so i could have wireless internet. I installed it and i was able to use it with the ethernet cable, however when i tried to use wifi, it worked for only about 2 minutes before it disconnected.. Now when i try again it says that it is connected (full 5 bars) but it also says there is no internet access and i cannot use the internet.
Also, before, with the old modem i was able to just connect the ethernet cable to the laptop and just start using the internet. Now i have to connect by putting in my username and password provided by my ISP almost like if it was dial up. I don't know why i have to do this now but not before.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 380 @ 2.53GHz, Intel64 Family 6 Model
[Code].....
My neighbor is using my Belkin Router the basic one and has comcast. We both use his internet and have had no problems until the past 3 days. He just got the home phone service from comcast and the phone line is setup through the modem. Ever since comcast came to his apartment and set this up the home phone service to his modem the router is connected but there is no internet access. What is going on and how can I fix this. He has an HP with windows Vista and I have a Toshiba Satellite L675 that has Windows 7 Home premium edition on it.
View 1 Replies View RelatedWhen I looked up the internet connection status, for the packets that I received 236, I only receive 30-40. When I click repair, it said the IP address already renewed. However, the internet still not working. When I use my laptop to browse the internet, it said the same thing, internet connected but cannot browse at all.
I tried so many things, such as clearing the DNS cache, releasing and renewing IP address, I did set the properties of the wireless connection to obtain DNS and IP automatically, I tried pinging, I turned off all my firewalls, I tried system restore, but still not working.
I run cmd /all, it got the following information:
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.0.1
When I did ping test, it said destination net unreachable, and later on I run ping test again, it said unreleased.
Later on, I did restart everything again, the packets that I received only 26, and didn't receive anything at all.
connect my PC/tablet with wifi router, I have bought wifi router which works with USB modem, when i connect my USB Modem i can see all the lights up (singnal- wifi, 2g/3g) and also showing in my laptop that is connect to wifi but unable to open the internet.
View 1 Replies View RelatedI am able to connect to internet using micromax modem having aircel sim.But "no network access" message is shown and so i am not able to accesss any website.
View 1 Replies View RelatedI have a bt wireless modem although it will not allow me to connect to the Internet over wireless although it will though ethernet.
View 1 Replies View RelatedToday I purchased a Motorola SURFboard extreme Cable Modem DOCSIS 3.0 in order to replace my old modem which is out of date and has been very slow as of late. I connected the coaxial cable, Ethernet cable(to Linksys wireless router), and power expecting it to simply work. All four lights came on green (power, downstream, upstream, connectivity). The downstream light turned blue which indicates a bonded connection.The device light was blinking on the modem. I connected to my wireless router, but no internet access. I then tried connecting my laptop to the modem directly via Ethernet cable, still no access. I think that rules out the router being the problem. I also ruled out my laptop being the problem as the same thing is occurring with my other laptop and desktop. I called my ISP (Cox Cable) and had them re-establish connection with my modem, this did nothing. I thought for sure this meant I had purchased a faulty modem; I hooked up my old modem and the results were the same, the modem connected fully with no problem (all four lights were green) but I have no internet access.
View 3 Replies View RelatedI was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
I have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies View RelatedI've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View RelatedWe have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedLinksys Wireless router connected but no access to the internet. I do not have a modem in my flat from ISP, only a cable, since the internet is set for every apartment in the building. I have a username and password that I use to connect. There is no problem connecting with the cable. I set up by Belkin wireless router and I'm actually connected to internet wireless but it only works if I also enable the primary ISP connection on my computer so my laptop is connected to internet without a cable. But this weird connection does not allow me to connect my phone to wireless or any other computer. Also the router settings site says not connected to internet and the internet light on Belkin is off.I have a Slovenian ISP -Amis, cable connection and Belkin Wireless modem, Avira Free antivirus.
View 3 Replies View RelatedLinksys Wireless router connected but no access to the internet?
View 19 Replies View RelatedI have a Belkin G Wireless Router which until recently, apart from a few signal drop-outs, was working fine.A couple of weeks ago, I tried to connect to the internet but despite the icon on my netbook showing that my Wireless Network Connection is connected and has excellent strength, I am unable to open any webpages etc. I tried re-booting the router but it is still not working.
The modem is working fine as I am able to access the netbook if I plug my netbook into it directly and I don't think it is an issue with my netbook as I have the same problem if I try to connect my HTC Smartphone to the internet through Wi-Fi too, eg recognises signal but cannot access pages.The router was permanently plugged in and turned on which I have since heard tends to burn them out so I am thinking it might be an issue with the router.
We are using a ADSL 827h in one of our sites. This router has worked fine until a month ago. Users are losing access to the internet overnight. The VPN tunnel stays connected, users are unable to get to any outside websites, i.e. Yahoo, google. We unplug the router and it comes back fine; until the next time.
View 2 Replies View Relatedhow do you set up an ethernet port for DHCP with a Belkin ADSl modem with wireless G router, model number F5D7632-4?
View 1 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
I am connected to the internet using a Huawei wireless USB modem connected to my desktop computer(no other type of service available) I would like to set up a Wifi home network so that I can connect using Wifi to all of the other gadget that I have in the house. So the question is can I connect a Wifi router using a ethernet cable comming from my desktop computer? and if so what router would you recommend for this application?
View 4 Replies View RelatedI have a hardwired HP computer with no problem connecting. The remainder of my wireless devices will not access internet. No problem until about 3 weeks ago then all of a sudden it stopped. All wireless devices detect the router/network, but will not allow access to the internet.
View 1 Replies View RelatedI have a Linksys E1000 device that is connected to a DSL connection through a modem. I have a Laptop that is wirelessly connected to the router and a PC that is connected via cable. Lately, a problem started to occur where the router keeps losing the internet connection and Laptop tell me that it connected to the router but there in no internet access and the same thing happens to the PC, both disconnect at the same time. I called my ISP company when this happens and they told me that the connection is working fine and everything look ok from there. I connected my PC directly to the modem and it worked fine so problem is not from modem. When i go to the router settings at the moment this occurs, it shows that all IPs are 00000 and status is "Connecting" and then it connects and changes to "connected" and everything fine till like 15 minutes later where this happens again (sometimes, it actually disconnects again after like 15 seconds!). I took the router to the dealer and he examined it and told me there is nothing wrong but he updated the firmware and told me to try it but same thing so he exchanged it for a new one and problem is still there!
View 3 Replies View Relatedi have a WRT54G2 and i have it plugged in. i want to avoid downloading things but i had this thing working a month ago, it says its connected but no internet connection.
View 3 Replies View RelatedRegion : Malaysia
Model : TL-MR3040
Hardware Version : V1
Firmware Version : TL-MR3040_V1_120822
ISP : MAXIS
I've got an issue with my TL-MR3040. Need assistance.- Modem HuaweiE398 (Identified) and connected to internet as seen on the webgui. Connected to my TL-MR3040 via wireless and connected BUT no internet access to the web.Tested using RJ45 cable to direct connect PC to Router, NO ISSUE with internet access to web.Need to know is my TL-MR3040 got defects or faulty?
I've looked through the forums and FAQs and haven't seen anything that resolves my issue. I recently moved from the US to Japan. I had my WRT54GS set up in the States and the network worked fine. When i got here, i set it up, hard reset the router and set up a new network.
I can access the internet when connected through the router via ethernet cable, but I cannot connect any of my wireless devices. Easy Link Advisor says "internet connection is not working" but it is. I have two computers connected via cable and they both work so it is not an issue of my ISP allowing multiple IP addresses.
My wireless devices (XBox, PS3, laptop) can see the network but cannot connect through to the internet. I also just noticed that the "wireless mode" according to the EasyLink Advisor says "disable", however the wireless settings on my 192. server webpage is set to "mixed" and seems to be correct in all settings to be on.
At home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies View RelatedI have am unable to access the Internet via my modem and router. My computer recognized the connection from my router. My modem is a Motorola 12DVC. My router is a Linksys Broadband Wireless-B BEFW11S4 version 4. I tried several things, including changes via 192.168.1.1. I am using an AT&T DSL connection. The router has only been used one time.
Here is some other information:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsJim>ipconfig /all
[Code].....
My main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
View 5 Replies View RelatedI have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View Related