I have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 RepliesRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
watch netflix on my tv,which has netflix,but has a Ethernet connection,and must use a rj45 cable,can I change it over to a wireless signal,so I won';t have to use a cable?
View 1 Replies View RelatedWould this work ?. also, on the back of the modem is a rectangular, not the typical, usb slot. I cannot move the modem because it is connected to the wall. I don't want to use an extra long wire either. What do I need to buy so I can use the wired modem, as a wireless one on my pc downstairs ?
View 6 Replies View RelatedI have a bt wireless modem although it will not allow me to connect to the Internet over wireless although it will though ethernet.
View 1 Replies View RelatedI wanna Know That I hab a nokia siemens SL2_141 modem which is not in use...beacause I dont have anymore BSNL connection. Now I am using A Wireless Modem of MTS. Recently I have Buyed New Phone I wanna Use wifi...
HOw Can I connect Internet of my Wireless Modem to The Wifi of nokia siemens SL2_141 Modem.I have Attached A photo So that U ppl Understand properly.
I've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View RelatedRegion : India
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP : Reliance
I got a new broad band connection , its with an ADSL modem (ZTE ZXDSL 831). Now i want to plug in my TL-WR841N to use my WiFi and to connect to my second machine!! no matter what setup i try, i'm unable to connect
We have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedI own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies View Relatedhow do you set up an ethernet port for DHCP with a Belkin ADSl modem with wireless G router, model number F5D7632-4?
View 1 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
I have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies View RelatedAt home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedHow to connect wireless modem in place of wired modem
View 1 Replies View RelatedI have a wired ADSL modem+router, and also a Linksys WRT54G2 V1 router. How do I connect them such that I get a working wifi available?
View 1 Replies View RelatedJust got cable and new hardware and been running bandwidth tests. I know wired is always going to be faster than wireless but was wondering if there were things I can do to see where the bottleneck is.
I have cable internet with a sb6120 modem and the asus rt-n56u router. When I go wired, I get 40+mbs down and when I go wireless I'm getting approx 20mbs down. Dont get me wrong, this is more than adequate but was wondering why the huge difference. I'm not anywhere close to the theoretical max.
The rt-n56u is on firmware 1.0.1.7f which is current. My desktop uses the WMP600n and my laptop has the Intel 5100 AGN built into it - both have updated firmwares.
I have an ADSL router like the one showed below & internet from the provider via a RJ45 cable.
I need to share the incoming internet from the RJ45 cable to the remaining three RJ45s & over the wireless. How to configure the router to get this working?
Also the internet provider needs me to authenticate via their default webpage before I can access the internet & I can say it doesn't have any MAC binding.
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View RelatedI'm attempting to connect multiple computers, laptops and printers to the same LAN. I currently have the switch daisy chained to the modem. I'm having issues with conflicting IP addresses and wireless access. I think I have to create static IP addresses but don't know which nor how.The hardware I'm seeking to have on one LAN:
- Netgear CGD24G Cable Modem from Time Warner
- Netgear GS116E un-managed switch
- iMac OSX 10.8.x
- Dell PC desktop, Windows 7
- Sony Vaio PC desktop, Windows XP
- Dell PC desktop, Windows XP
- Sony Vaio laptop, Windows 7 Pro
- MacAir OSX 10.8.x
- MacBook Pro OSX (not sure which OS version)
- HP JetDirect 300x Print Serve (hooked up to HP LaserJet 2300)
- Epson Artisan 835
- Netgear Universal Adapter for Home Entertainment (SAVB5004)
- Netgear Powerline 500 Nano
- Apple iPhones (4 of these)
- Apple iPad
Several of these can work wirelessly, though I prefer wired whenever possible.I have been getting IP address conflict notices as well as the wireless signal not being received on some of the wireless capable devices, which seems to be random but it could be that I just don't know enough to recognize a pattern. I believe the devices are all set to automatic assignment of IP addresses.What is the correct way to daisy chain the cable modem and switch?What is the correct protocol for assignment of IP addresses in order to avoid IP conflict?Why does my wireless drop on some of the wireless-capable devices (such as the iMac, MacAir or Sony laptop)?
I am using the WRT54G2 connected to a cable modem that requires a PPPoE login. I followed the Service Providers instructions and cloned the modems MAC address to the WRT54G and setup the PPPoE user id and password. I can then plug my PC into one of the Ethernet connections on the back of the WRT54G and everything works as expected. First I connect to the WRT54G2 and then I open a PPPoE connection in my network settings and it logs into the service provider and everything works as expected. But when I connect to the WRT5G2 wirelessly I connect to the AP fine. When I open the same PPPoE connection to the service provider it fails, the message says I have the wrong userid or password or that the protocol is not supported. Of course I know the userid and password is correct because it works when connected with Ethernet cable. I have tried disabling the security on the wireless network but that did not seem to work.The modem is a HomePNA HCNA Voice Endpoint.I am at the latest firmware 1.0.04.
View 7 Replies View RelatedI tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies View RelatedI'm trying to connect a PC to an existing wireless Modem which has a laptop already using it. I've somehow deleted the wireless connection symbol from the bar at the bottom.
View 9 Replies View RelatedWe have a modem at home but it doesn't have built in wifi so we have it connected to a router. We have fast internet (ADSL2 i think) but running through the router, it's very slow. So i was wondering if i could somehow make my laptop a modem? Or a router as well because it would have to be faster than the one we have now. Im running a Acer Aspire 1830 Notebook 32-bit windows simple language when replying
View 1 Replies View Relatedrecently i got a dlink dir 615 router from a friend. i'm using adsl modem now. i want to connect the modem to the router so that i have a wireless at home for my laptop and iphone. i have follow the step in the router manual but it did not work. i just cannot conect to the router page through the 192.168.0.1 i am using windows vista home basic.
View 15 Replies View RelatedI have a modem/router at one end of my house, but the WiFi doesn't reach the other end of the house (where I have my other PC). If I bought a second modem/router and plugged it in next to my computer, would that work?and if so, would I have to turn one modem off to use the other?
View 1 Replies View RelatedI have an HP Pavilion wireless laptop with windows vista and a gateway desktop, windows XP Home edition and every thing worked ok untill I got a virus on my desktop Since then I've formated the hard disks and reloaded the opering systems, but I don't know how to get the laptop working wirelessly without taking the motorola modem and connecting it directly to the laptop, I have a D-Link DIR-615 router.
View 4 Replies View RelatedI recently upgraded my DSL service, which required installing a new VDSL modem/wireless router (Actiontec c1000a.) Before the upgrade, I was using an older standalone DSL modem with a Netgear router to provide wireless access to my gaming consoles, laptop, etc. Everything works as before with my new wireless router EXCEPT my son's laptop. All my consoles, iPods, and desktop CAN connect to the wireless network, and the laptop will connect over a WIRED ethernet connection. I cannot get it to connect to the wifi.
[code]....
I have AT&T 2wire wireless modem. I am working on a friend's computer and his computer detects the modem but won't connect. I have entered the 10 digit number on the router into his laptop and then I tried the homegroup password and still it won't connect.
View 6 Replies View RelatedI have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]
View 7 Replies View Related