I have an ADSL router like the one showed below & internet from the provider via a RJ45 cable.
I need to share the incoming internet from the RJ45 cable to the remaining three RJ45s & over the wireless. How to configure the router to get this working?
Also the internet provider needs me to authenticate via their default webpage before I can access the internet & I can say it doesn't have any MAC binding.
i want to know the function of 8wire of RJ45 port
View 3 Replies View RelatedHotels have wired LAN connections and not wireless. Is there a device that will plug into the ethernet cable and offer wi-fi for more than one laptop/smart phone in the hotel room?
View 1 Replies View RelatedI have this adsl wireless router but my internet connection only has RJ45 directly connected to my PC. My questions is how can I use my ADSL wireless router with this kind of internet connection.. because I really want to make my connection wireless..
View 1 Replies View Relatedis there an adapter ( wifi reciver ) that plug into RJ45 port so RJ45 can receive wifi signal ?
View 1 Replies View RelatedI have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View Relatedi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedI have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies View RelatedNot too much networking savvy - but here goes. Want to use router as local lan - no wireless. When router is connected to laptop via RJ45 I loose my ability to connect to sites via browser. IPconfig shows wireless adapter at 192.168.1.3. When router is attached it's ip is 192.168.1.1. Disabled the wireless in the settings but no dice. When the router was used with DSL it was set at PPPoE but now that I'm just using it locally not sure whether it should be DHCP or Static or other.
View 3 Replies View RelatedHow do I convert my wireless router to a wireless AP (Access Point)?While connected to the main router go Start then Run in XP - (Windows key plus R in Vista and Windows 7), then type in the following, including all the spaces:- cmd /k ipconfig /all -- then press Enter and from the black form that shows up, take a note of the numeric code beside the word "gateway" -- usually something like 192.168.0.1. Type exit to close the black form.Now connect the router to be converted only to a computer via network cable and log in Setup the wireless security Disable the DHCP and change the LAN IP to match the gateway IP but ending in something like .253 Finally connect one of the four LAN ports of the AP to the main router, do NOT use the WAN port.
View 4 Replies View RelatedI have a Belkin f5d7234-4 lying around at home. I also have a Panasonic TV which requires a proprietary wifi donge to get a wireless signal, so my question is, can I use the router to recieve my house Wifi (broadcast by my new NetGear Router) and send it out through its Ethernet port to the TV?
I checked, the router doesn't have ddwrt support, I'm new to hacking around with routers and networks, so I don't know how to do this, I see how it is logically possible
We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies View RelatedI live in an apartment where my internet is included in the rent. In all the rooms there is an ethernet socket buillt into the wall. I'd like to know how to connect a router to this for wireless internet. I have tried one router, but it buggers up the ip address and brings down the network for the entire apartment complex. I've done this twice now and don't fancy waiting another week for the technician to call out to reset things. I had a friend who lived in a simalar complex, rj45 sockets on the wall etc. He has a thomson router, which has a little black box plugged into the ethernet socket on the back of the router. Into this little black box goes the ethernet cable from the wall socket and bam, he has wireless internet, even though he has no access to the main router or switch of the apartment block. It's not failed once either. Both the router and the little black box need mains power.I think it was originally for a WIMAX connection. It's small, maybe 2"X3" inch?
View 3 Replies View RelatedI just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies View RelatedI have a new router with RJ11 input....but from my DSL Modem, the output is Rj45.how can i connect it...
View 1 Replies View RelatedTrying to convert a spare router (Linksys E3200) into a wireless access point to extend my wireless coverage. I thought knew how to do this but having a problem.The problem I am having is that after I finish step 2 the router reboots with the browser trying to access it at the new ip address. But the browser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected by an ethernet cable. I also tried it wireless with the same result.
View 3 Replies View RelatedI am running a wrt54g and I was woundering what is the longest rj45 cable length I can run?
I notice running about 30 plus feet connection does not work. When I cut off about 5 feet it worked. Seems I can only run a ceratin amount of cable length with this router.
I have an internet connection that enters my house using a CAT5 cable through RJ45 type socket - Currently I have a desktop that is connected to the Cable - I want to share my internet connection - The desktop should have a cable connection and want to connect a laptop as well which will connect using wireless as well as cable as and when required - I will not be using both computers at all times so do not want to make my desktop a server or the laptop a server.
View 3 Replies View RelatedPurchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
How do you convert a D-Link router into a repeater?
View 1 Replies View RelatedMy desktop however, does not have built-in wireless and therefore would have to connect to the ADSL router (Netgear) through ethernet but this cannot be done as the router must remain in my bedroom, much too far away for cables to reach.I bought a USB wireless connecter for the desktop but it doesn't seem to work. It connects but gives "Local Only" as the connection.
View 9 Replies View RelatedI have a BT broadband connection with one of their BT Home Hub 2 routers. Within the house the wireless signal is fine, however I have an outside office in the garden which is just beyond the normal range of the wireless signal. I tested this by connecting using my DELL XPS Win7 laptop and walking from the house to the office and it lost the signal about 10 feet short!
Is there any way to extend the range of the wireless signal? I cannot use homeplugs as the office is on a different fuse box from the house.
The BT Home Hub 2 is an ADSL router using n technology.
I do have a spare Netgear N150 ADSL2+ wireless router, is there any way of using it to boost the range of the signal?
have a dynex wired router set up to use xbox live. now want to add adsl westell wireless router so we can use ipod touch & kindle.dont want to disturb the xbox set up.
View 7 Replies View RelatedI have a router that is not wireless that I have three computers running from by ethernet and attached to that a wireless router without any ethernet ports. I have mac addressed access only set up and need to add a device to the wireless. However I can not access the wireless router from my computer which is plugged into the other router.
View 1 Replies View RelatedI have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedA friend of mine has given me a D-link DIR-615 Wireless Router. I only have a copper 10 meg ADSL service. The Router Internet socket is an RJ45, the ADSL Filters are RJ11. Is it possible to get this router to work on an ADSL Filter ? Can you get ADSL Filters with both an RJ45 and BT Phone connection on them, or a converter lead which converts RJ45 to RJ11 to work on the current ADSL filter?
View 5 Replies View RelatedIs it possible to use ADSL Wireless router (one with RJ11 WAN in) to connect to cable net? If not is there any which can allow me to connect to cable net in future if in case I change to cable net ISP.
View 2 Replies View RelatedI've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View RelatedI hav bsnl broadband connection in my home.... I connected a tplink wired for browsing...I also have a belkin wireless router..... I connected those routers.... And only wired communication is possible
View 7 Replies View RelatedWe have a router operating in front of one computer which is separate from the rest of the network. Most of the time it operates fine but we find sometimes it loses connectivity, both internet connectivity from the machine and access to the machine remotely. This is not acceptable as the machine is operating rather critical processes and ideally it should be available 100% of the time.
I cannot determine if the fault lies with Windows, the router or the network.
ADSL Connection Type PPPoE/PPPoA
Firmware v1.06
Port forwarding None
DNS Auto
Firewall None
DMZ 192.168.1.2
I Got a new ADSL connection,They provided a ADSL Modem. To connect tot he ADSl i have to enter the username/password in the PC....in this case how can i make this ADSL connection to wireless? coz Me and my friend want to use the same connection.
View 1 Replies View RelatedI am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.
View 2 Replies View Related