A friend of mine has given me a D-link DIR-615 Wireless Router. I only have a copper 10 meg ADSL service. The Router Internet socket is an RJ45, the ADSL Filters are RJ11. Is it possible to get this router to work on an ADSL Filter ? Can you get ADSL Filters with both an RJ45 and BT Phone connection on them, or a converter lead which converts RJ45 to RJ11 to work on the current ADSL filter?
View 5 RepliesI had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
View 14 Replies View RelatedIs there any way I can make the cisco 857 router work on ADSL over ISDN?
View 2 Replies View RelatedI've recently upgraded my internet provider to BT and received a BT Home Hub 3 as the new wireless router.Previous to this I was using a wireless Belkin G + MIMO ADSL router (model number F5D9630-4).There are places in the house where the wireless signal is very poor. Connecting to the internet using either of these routers is difficult in these spots. However, since the Belkin is now spare, I've been thinking about trying to use it as a low cost repeater (i.e. free) to extend the wireless range in the house.There are several good articles that I've found on this site which address the connection of two routers together (e.g. John Will's article on connecting two SOHO routers is a good example), but they rely on an ethernet connection between the two routers. Any way to establish a wireless link between the two routers to extend the range of the current wireless network.
View 9 Replies View RelatedWe have Cisco ASA 5520 with csc ssm 10 (product ver. Trend Micro InterScan for Cisco CSC SSM 6.6.1125.0)in Web>Global settings> URL filtering > Rules > Communications and Search> Social Networking category is set to block during work time and allow during leisure time(see the attachement), but rule for this category won't work. I mean social networking sites are always remain allowed.
View 2 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
I want to make a question about RV042. I used RV042 router in my office. I used content filter feature in router.Althought this have not been apply the rules. I think I made wrong rules.I enabled the block enable forbbiden domain .And then added the websites that I want block.However, these websites are still browsing in local computer.
View 4 Replies View RelatedModel : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?
URL List Type: Deny Allow Disable
Address Port Remove
[URL]
I have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
View 5 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : DEMON
I'm using parental controls to block all devices in the house from using tumblr. I cannot do this at a device by device level as it is being used on iphones/androids, laptops and desktops.Unfortunately, the way that tumblr works is that it use many URLs for the different pages people set up so it is not just a case of blocking url... - so I'm struggling to work out if I can do this via URL blocking on the router settings. How to do this at router level.
I'm expanding my home network and the adsl modem router supplied by my ISP has just 1 RJ-45 port and 1 usb port (and an RJ-11 for the Internet). I have zeroed in on TP-Link TD-W8901G having 4 RJ-45 ports, 1 USB port, 1 RJ-11 port and also it is a wireless router. Currently I would be connecting the above modem router to my desktop running Linux and using the same ISP with ADSL. Considering a future scenario where I may decide to use another way to connect to the Internet like maybe 3G or Cable, etc (with their separate modems) I was wondering if my same modem router (TD-W8901G) could be used as a standalone router for connecting the devices on my home network. Basically, what I want to know is whether this modem router would be able to share an Internet connection from some other source, other than the one provided through its own RJ-11 (ADSL) source?
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedI recently modified my home network in hopes of getting faster file transfers between devices. But it looks like something's not right.I'm suing Lan Speed Test and the best performance I get over WiFi is about 44Mbps (avg.). From my laptop to my NAS. If i turn off the WiFi and do the test over a wired connection the best I get is 200Mbps (avg.).
1. AT&T 2Wire cable modem. Internet comes in the house through this box and it's currently set up to be in bridge mode so that the TPLink router handles everything.
2. TP-Link WDR3600 gigabit/wireless router set to work in 5Ghz only, 11an mixed mode.
3. WD My Book Network Storage. Wired gigabit connection.
4. Desktop PC. Wired gigabit connection.
5. Laptop PC. Wireless.
6. 1 ipad v.2, 2 iphone v.5. Wireless.
Current setup:
1. internet cable goes into 2Wire Modem.Wireless on this device is OFF.
2. cable goes from LAN port on modem to WDR3600 router's internet port
3. cables go out from router to Desktop PC and NAS
4. all other devices are connected to the 5GHz wireless network created by the router.
i have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedRegion : Brazil
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telemar Oi Velox
Very weird situation... can't get full speed with the TD-W8968 with my DSL link..
We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom
Below you point out my attenuation values detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
I have used all the spots on the form to filter mac addresses. Is there some way to add more? I have a lot of friends that come over from time to time. I also have plenty of my own wireless devices.I like using the mac address filter so not using it is not an option. Hopefully there is a way to add more, instead of being limited to a predetermined amount.
View 3 Replies View RelatedI am trying to block port scans originating in the Russian Federation, thousands per day. I entered 77.88.26.0 as the Remote IP Start and 77.88.26.255 as the Remote IP End, setting the action to Deny. It shows in the inbound filter rules list but my linux server still receives thousands of scans daily from an ip address in that IP netblock. My DIR-655 is running hardware version A3 and firmware 1.34NA.
View 8 Replies View RelatedRegion : India
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP : Reliance
I got a new broad band connection , its with an ADSL modem (ZTE ZXDSL 831). Now i want to plug in my TL-WR841N to use my WiFi and to connect to my second machine!! no matter what setup i try, i'm unable to connect
Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
I installed the 2.06NA on my DIR-655 router and now I'm having problems adding mac addresses to the network filter. The message is "Invalid MAC address". Of course, it doesn't tell me which entry is invalid and I have a number of them. After further checking.. I noticed that one of the MAC addresses is indeed invalid and when I remove it I still get the error message?
View 1 Replies View RelatedI had no problem running both 2.4 and 5.0 Bandwidth. With WiFi password and without. It does it's job. The 2.4Ghz Range Plus works. I have set up the router on the 2nd floor at the highest it can go. And everyone get's full bars all over the house. I even get 4-5 bars outside in my car on my phone.
The only issue I have with this thing is a damn new netbook I got for Christmas with a Mac Address starting with 0C-EE-E6-XX-XX-XX. The Router finds the Mac Address invalid. In which I can come to understand cause seeing a Mac Address starting like that is completely new to me. Every Mac Address I have, started with 00 except the netbook. So now, I spent days trying to find firmware updates, patches, anything! I even attempted to spoof the Mac Address on the netbook but Microsoft has a bug on Windows 7. (I have the Starter Edition that came with the netbook)
Windows 7 Mac Spoofing works with WIRED Connection. But it does not work with WIRELESS Connection. I used 3rd Party Tools: SMAC and etc... I attempted Registry Edits, I changed even the value key to the "Orginal Mac Address" and it just wont change [New Strings/Network Address Edits included]. I have been banging my head about this for a week now. The Internets has many answers but they did not work. So Spoofing the Mac Address is out of the question. Until Microsoft fixes this bug.
Anyway: Did D-Link release any sort of beta update/driver/firmware or anything to resolve this at all? Is there a modded firmware to force the Router to take this stupid paradox of a Mac Address?
Currently: I have the Router's WiFi Password-ed with Default Factory Settings
{Hardware Version: B1
Firmware Version: 2.02NA}.
207.NA Firmware, B1 Hardware in use on a DIR-655, Time Warner Cable setup. Nothing to do with Revision, cordless phones,I saw this asked once before specifically here, but it was never answered.After several attacks via our cable network and neighbors, we've HAD to turn on MAC filtering. There are TONS of devices attached normally so two situations popped up:
#1: What happens when you max out the authorized MAC address listings? Does the page get longer when you save/reboot it? Do I have to do it manually from there forward and where can I get down to the core programming level to edit the code and put the MAC's that are around and on 100% of the time to open up the plug-in list on the GUI?
#2: Guest Zone - we NEED a way to have random guests get on our Network with a different password we can randomly change to prevent the outside abuse, etc. but am I understanding what little else has been posted that the MAC filtering also covers the Guest Zone and therefore I have to stick them in there before they could simply log on with the current password? Is there any way to change/stop that without eliminating MAC filtration as a whole?
I want to add more than 40 mac address filter into my WRT54GL with firm version V4.30.7 but the form to enter the mac address list just limited to 40 mac address register. How do I can add more than 40 mac address list in my WRT54GL ? perhaps we can add the list into WRT54GL like XML file or somehow that can make me add more than 40 mac address register list.
View 2 Replies View RelatedIt would be nice if there was a "Note" field next to each MAC field whereby you could specify what device the MAC belongs to. I have quite a few listed but recently I've gotten rid of the devices. I have to go through all my current devices, not them in another program, and then remove the ones that are no longer needed.
The Wireless Client List doesn't capture all the names so that's not what I'm looking for.
Also, it would be great if the "Note" would tie into the Parental Controls so that I know exactly what device I'm choosing. It currently lets you select from the Wireless Client List, but the list doesn't have all the Client Names populated.
So, one, is this feature available (or something similar) and two, if not, please take this into consideration as a useful feature for a new version down the road.
When the front-panel WLAN LED light is solid, it indicates that the wireless segment is ready; it blinks during actual wireless data transmission. This is how it behaved for me until I added some MAC addresses to Advanced > Network Filter. Now it stays solid even during wireless data transmission. Even after a reboot. If not, how do I get the blinking back?
View 14 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View RelatedTwo issues with WRTP54G
1.) when making changes and restarting the router I am unable to get web pages (wired port or wireless) or web response from the router, despite re-entering the URL (192.xxx.x.x). I *DO* get a dialtone (VoIP). To get router restarted I have to get my lazy arse up and cycle power to the router. Like I said, a nuisance.Configured for WPA2 Personal security with MAC Wireless Filtering (9 MACs)
2.) Adding a 10th wireless device to the filter table and the MAC 10: becomes duplicated in MAC 09: while the existing MAC 09: disappears. Finally got it to accept my new device but now I have 2 devices repeated in the MAC Filter Table. Not a clean setup.