Trying to convert a spare router (Linksys E3200) into a wireless access point to extend my wireless coverage. I thought knew how to do this but having a problem.The problem I am having is that after I finish step 2 the router reboots with the browser trying to access it at the new ip address. But the browser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected by an ethernet cable. I also tried it wireless with the same result.
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
I have an ADSL router like the one showed below & internet from the provider via a RJ45 cable.
I need to share the incoming internet from the RJ45 cable to the remaining three RJ45s & over the wireless. How to configure the router to get this working?
Also the internet provider needs me to authenticate via their default webpage before I can access the internet & I can say it doesn't have any MAC binding.
How do I convert my wireless router to a wireless AP (Access Point)?While connected to the main router go Start then Run in XP - (Windows key plus R in Vista and Windows 7), then type in the following, including all the spaces:- cmd /k ipconfig /all -- then press Enter and from the black form that shows up, take a note of the numeric code beside the word "gateway" -- usually something like 192.168.0.1. Type exit to close the black form.Now connect the router to be converted only to a computer via network cable and log in Setup the wireless security Disable the DHCP and change the LAN IP to match the gateway IP but ending in something like .253 Finally connect one of the four LAN ports of the AP to the main router, do NOT use the WAN port.
I have a Belkin f5d7234-4 lying around at home. I also have a Panasonic TV which requires a proprietary wifi donge to get a wireless signal, so my question is, can I use the router to recieve my house Wifi (broadcast by my new NetGear Router) and send it out through its Ethernet port to the TV?
I checked, the router doesn't have ddwrt support, I'm new to hacking around with routers and networks, so I don't know how to do this, I see how it is logically possible
We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
I have a guest house in the back. I access the net there through my Dell laptop using WiFi. I have a television there that needs to have its operating system upgraded through the internet. All it has is a LAN connector. How do I get my Laptop to convert the WiFi to LAN so all I need to do is connect a LAN cable between my laptop and the TV? Or do I need to buy something cheap to convert WiFi to LAN?
is it possible to convert a 3G donugle into a hotspot?? i tried converting my LAN into a hotspot and it works. wondering if it is possible to do the same with my 3G doungle.
My Sony video camera saves in .m2ts. I need to convert the file to .avi for editing. Is there freeware available and what should the settings be for the best quality. Can PMB � Picture Motion Browser export to AVI?
My daughter is going to university. An Ethernet connection is provided but she wants to work wirelessly. Is there a gadget to attach to the Ethernet port that will create a wireless signal for her to connect her iPad and PC laptop?
It is possible to convert 802.11a to 802.11g wireless network device. I wireless outdoor cpe which is work on 802.11a...i want to convert it to G network
I have a cable internet.There is no other hardware that connects to the Cable.There is no modem or router.Just the RJ45 cable that I plug in to my laptop and go online.Now,I want to convert this to wifi.what router/modem will I require and possibly with the model number and something thats low in price.I will use only one laptop and no intention of multiple user.I dont intend to use printers either.I am using windows 7.The network adapters that are installed in my laptop are: Intel Centrino wireless N 1030.Microsoft virtual wifi miniport adapter and Microsoft virtual wifi miniport adapter #2,RealtekPCIe FE Family Controller?
I have a reliance netconnect + broadband connection (usb device) which I use to connect my laptop. Is there any device/ software which will convert this to WIFI so that I can use the same connection for my other WIFI enabled devices?
I have a wired IP phone connected to my company network, in my home office. How can I convert this to wireless so I may use other rooms in the house to work in?
I try to convert a CISCO ASA 8.2 version to 8.4 BUT, I have a small or "little" problem :On Cisco ASA 8.2.x, i have a possibility to create multi-line global with different subnet.Example :
global (outside) 2 217.1.x.65-217.x.x.66 netmask 255.255.255.240 global (outside) 1 interface <-- Ip interface is other subnet : 217.3.x.3 global (outside) 2 217.1.x.67 netmask 255.255.255.240 nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz2) 2 192.168.4.0 255.255.255.0
What is the method or solution to translate multi-global in 8.4 ? with static translation in 8.4 : i try to use different server in inside's zone, but not in same network on outside. In 8.2 Firmware, it's very easy to use that, but in 8.3-8.4 version, i don't have some idea to manipulate ...
interface Vlan1 description Lien vers reseau Interne Client nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0
I have a L2L tunnel I need to convert from 8.2 to 8.6 and need to understand the static policy Nat conversion. I have single hosts that require a 1-1 nat to addresses given to be my the vendor that reside on my firewall. Other works i have /24s that I static nat my inside host to so that the vendor can access the host for support.Example. server 10.11.103.44(real server on my inside network)
5.5.98.0/24-Defined for local traffic via L2Ltunnel object-group network Carebridge_Local description Mckesson Local network list network-object 5.5.98.0 255.255.255.0
