I have a modem/router at one end of my house, but the WiFi doesn't reach the other end of the house (where I have my other PC). If I bought a second modem/router and plugged it in next to my computer, would that work?and if so, would I have to turn one modem off to use the other?
View 1 RepliesRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
i just bought a Netgear WNDR4000 router due to troubles with my current modem/router combo (D-Link DSL2730-B). The router doesnt have in built modem functionality obviously so I need to set up the modem/router as a dedicated modem.Also should I use the current modem/router as the dedicated modem or an older model i own (I think its a DSL 502T)? Because the current one often drops the internet connection. Don't know if its a problem with the modem functionality or something else. Will the older one serve better since i didn't have any problems with that one or will it be outdated? I only upgraded due it not having wireless capabilities. Otherwise it's fine.Or will I be even better off buying a dedicated modem? I really don't want to spend more money but if this is a far better alternative I guess i will.
EDIT: Ok so found out that I have to put the modem/router in bridge mode in order for this to be possible. However, looking up how to do this lead me to a dead end because i need to fill in some fields that i have no idea how to interpret.
VPI:
VCI: These 2 already came with presets. Should I just leave them?
Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge): Choices of EoA PPPoA and IPoA
Encapsulation Mode: Choices of LLC/SNAP-BRIDGING and VC/MUX
Service Category: UBR without PCR, UBR with PCR, CBR, Non Realtime VBR, Realtime VBR
[code]...
I am setting up a 1921 with two ethernet WAN ports going to two seperate ADSL ISP's (via bridged modems) and one connecting to the internal LAN. There is a single e-mail / web server behind the router.
I have been reading the following which is exactly what we want to do, but I have questions. Maybe failover would be better because Load Balancing seems a little too quirky without BGP. url...
How do we define public static IP's, the example seems to show DHCP?In order to detect if a line is down, it has to ping an IP address that is specific to the connection - correct? So could I use the gateway for the ISP? The issue I have with this is the gateway might be up, but the Internet down. Next, we need to make sure that when someone visits one of our public IP addresses, the return data is sent through the connection requested. What we don't want is a situation where incoming connections are not working.From experience, load-balancing causes certain websites and SaaS applications to break because requests are coming from two different ISP's. Is this the case with OER? Finally, any links, config or something to advise how a fail over only configuration would work given we have internal servers (PAT/NAT inbound would need to translate properly with the failover IP)? Basically if ISP 1 goes down, I.E. router cannot ping 8.8.4.4 then it switches to ISP 2, until ISP 1 comes back online and switches back? This would need to change the NAT rules for inbound as described.
I have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View Relatedrecently i got a dlink dir 615 router from a friend. i'm using adsl modem now. i want to connect the modem to the router so that i have a wireless at home for my laptop and iphone. i have follow the step in the router manual but it did not work. i just cannot conect to the router page through the 192.168.0.1 i am using windows vista home basic.
View 15 Replies View RelatedI have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]
View 7 Replies View RelatedI want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies View RelatedI am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik ) outside to inside so when i call ip public then forrward to mikrotik
View 2 Replies View RelatedI have a bt wireless modem although it will not allow me to connect to the Internet over wireless although it will though ethernet.
View 1 Replies View RelatedI am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
View 2 Replies View RelatedI have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
View 1 Replies View RelatedI wanna Know That I hab a nokia siemens SL2_141 modem which is not in use...beacause I dont have anymore BSNL connection. Now I am using A Wireless Modem of MTS. Recently I have Buyed New Phone I wanna Use wifi...
HOw Can I connect Internet of my Wireless Modem to The Wifi of nokia siemens SL2_141 Modem.I have Attached A photo So that U ppl Understand properly.
I've got a ADSL Sweex Modem, connected to a D-Link Wireless Router,The modem is connected to our telephone line, we have other phones connected to other "telejack" too. The router is connected to a computer with wire, and another computer wireless.Every now and then we get random disconnect. Sometimes we can go several months without a single disconnect,whilst sometimes it happens as often as every 3 minute. This is the log:
[code]....
I use D-Link DIR-615. I can't connect to config page 192.168.1.1. I need to access ADSL modem config page. Asus RT-N12 can configADSL modem via Wi-Fi.
View 1 Replies View RelatedI'm trying to set up an IPSec tunnel between 2 3845 routers that each sit in a private LAN behind an ADSL modem. Each modem does have a static public IP address from the ISP.
Thus:
Cisco 3845-1 <-> ADSL modem <-> WAN <-> ADSL modem <-> Cisco 3845-2
3845-1
Gi 0/0 - private ip
l
NAT
[code]....
So I would like to set up IPSEC between the GI 0/0 interfaces on the 3845's.
I have an 1700 cisco Router and a ADSL connection to Internet.How may I use it on my home network?There's any configuration that I should to do?
View 3 Replies View Relatedconfiguring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.
I have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
how to connect a adsl modem to a computer network using a switch with a server.I have a network with a server and about ten clients computers all connected through a switch, the server has an IP 192.168.1.1 as its gateway. I want to connect adsl modem to the switch so that all the computers can have access to the net, but the adsl too has 192.168.1.1 as its IP.
View 1 Replies View RelatedModem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.
View 1 Replies View RelatedI'm expanding my home network and the adsl modem router supplied by my ISP has just 1 RJ-45 port and 1 usb port (and an RJ-11 for the Internet). I have zeroed in on TP-Link TD-W8901G having 4 RJ-45 ports, 1 USB port, 1 RJ-11 port and also it is a wireless router. Currently I would be connecting the above modem router to my desktop running Linux and using the same ISP with ADSL. Considering a future scenario where I may decide to use another way to connect to the Internet like maybe 3G or Cable, etc (with their separate modems) I was wondering if my same modem router (TD-W8901G) could be used as a standalone router for connecting the devices on my home network. Basically, what I want to know is whether this modem router would be able to share an Internet connection from some other source, other than the one provided through its own RJ-11 (ADSL) source?
View 1 Replies View RelatedI've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View Relatedi have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template
Is there is any reason for ths ? With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting
My Virtual Template config
interface Virtual-Template1
mtu 1440
ip unnumbered Loopback3
[Code].....
i have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies View RelatedDear The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template.With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting. [code]
View 2 Replies View Related! have a TELSTRA ADSL wireless router ( Thomson TG782T)I need to connect my 2 printers to it so I can operate them wirelessly to my laptop and Desktop computers
Laptop: TOSHIBA Satellite w/- windows 7 Professional
Desktop: ASI Computer w/- Windows 7 Ultimate currently connected to ADSL modem by yellow network cable.
I am wanting to force the n600 to g.dmt for a more stable connection. cannot work out how to do it. am force into using old modem as far from the dslam and forcing adsl 1 improves performance.
View 4 Replies View RelatedI have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?
View 1 Replies View RelatedHow can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
ADSL Modem ---> Firewall --> Switch--> Computers
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
View 2 Replies View Related