Broadband :: Changing Previous Owners Details And Settings?
Jun 17, 2011
bought a second hand laptop but all previous owners details are still in. they must have been on a dial-up network want to change to broadband,how? also need to sort out wifi.
I just flashed this router with DD-WRT about a week ago inside the webui that was provided. It all went well but I wanted to go back to the original factory firmware so turned it off for 20 seconds, and held the reset button for 10 seconds to reach the emergency-room. I re-flashed it with the firmware I got from d-links website and all went well. So I tried to go to 192.168.0.1 that did not work so I tried the ip that I gave it before it was flashed and it still remained x.x.x.254. I also turned off dhcp server since my isp's modem provides that and other services. But when I looked into the logs it would keep starting up dhcp server every minute which would lead to all kinds of problems.
Edit: The ip/subnet are set to 192.168.0.1/255.255.255.0. It seems to start this as soon as dhcp is disabled.
LOG: 11:56:02 device_lan_ip=, device_lan_subnet_mask= 11:56:02 DHCP Server Start 11:55:51 device_lan_ip=, device_lan_subnet_mask= 11:55:51 DHCP Server Start 11:55:40 device_lan_ip=, device_lan_subnet_mask= 11:55:40 DHCP Server Start
I got 4 aironet 1310 Œ but i don't have password into Enable mode!. I follow this document "Password Recovery Procedure for the Cisco Aironet Equipment.pdf" to recovery password. It succeed reset password to default Œ but it also reset Previous setting to default.
Can I reset aironet 1310 password and keep Previous setting?
Every so often (random amounts of time) my internet setting either on the router or pc change and then I it comes up with an error that my settings aren't the same as my router... I use a Orange Live box and windows 7. also when I want to sign into games for windows that sometime crashes the internet and on DOW2 and minecraft.
I had a disaster occur on my "guest" OS within VMware-Player. I had to start over from scratch! I am back in business, except for having the virtual machine recognized by my existing wireless network. The other two computers still communicate.I went through the wireless setup routine for the new VM. A new "ID" was assigned. Obviously, this is different from the one currently in use on the network. I have the settings info on a flash drive. Can I simply insert the FD in the other two computers and have the new ID replace the existing one?
I need to change my DCS-942L camera settings remotely when I am not connected to my home wireless network. When I am at home, I just type in the local IP address of the camera (192.168.0.100) into my browser to access the firmware. How can I do the same when I am away from home and obviously not connected to the local WiFi?
I have a RCA modem from comcast high speed internet.Also have a Linksys Cisco Wireless-N Gigabit Router model # WRT310N V2. When I connect the internet directly into the computer, I get download speed up to 21.07 mbps and upload speed of 3.07. When I connect through the router download speed 1.31mbps and upload speed of 1.01.I have no clue how to make changes to the router.
I have an Ubuntu 10.04 and basically I would like to achieve this:When I am at home, switch the network to use static IP.When I am at the office, switch the network to use DHCP.
Is there a program to do this?Or is this something that should go inside an init script where if it is weekend or weekday from 7 pm to 7 am, then consider it a home. If it is home, then use static IP.?
When I change a setup setting and click save settings, most of the time it gets stuck on the "saving..." notification window and eventually I get a "Internet Explorer cannot display the web page" notification. However I have found that if I repeatedly try it eventually it will accept the change. This never happens using the wizards only making manual changes. I am running the camera with a Wi-Fi connection. I am not sure this is a router or camera firmware bug (running V1.12)
Modem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
I am working on installing a new 2500 Controller with 2 AIR-LAP1242G's attached to it. I have both registered and on the controller but I am having trouble moving one of them to a new IPS AP group that I created. Furthermore, I noticed the default gateway is missing from the static ip settings and I am unable to add that as well. When I add the default gateway and hit apply, the controller does nothing. Same thing for when I try to change my WIPS device to monitor mode.
A couple other things that I noticed is that when I go to AP groups and try to remove the AP's from the default group, there is no remove button when you go inside the default group like I see when i go into my IPS group.The AP's are on software ver 12.4(23c)JA3 Boot ver 12.4.13.0 and the controller is at 7.0.22.0I have already power cycled the controller and both AP's.
We are leasing an office space from a building that has it's own network center. This center can be used by each office/company to either house their own networking solutions or utilize their internet access if you plan only to use cloud servers or NAS servers. Our company (4 employees) is using this network center only for internet access with all of our data stored and accessed in our cloud service.We would like to access the internet wirelessly, which building does not provide. We were given one port and shared the link through the use of a switch. So my questions is would an access point add wireless connectivity without any information (ISP?) provided by the network center? I am not sure yet if we will be purchasing a router/AP or device made for to be used as an AP.
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
I have a Belkin aigo True Mimo PreN Router model FD 582304. I am trying to wireless connect a new laptop on windows 7. It wont accept the WEP key I have previously used. The router is cable connected to my desk top computer. How do I find out the details of the WEP key for this router or reset all.
My download speed has decreased to about 1/40th of its previous speed, while my upload speed remains the same. Speedtest shows that my connection is equally strong as it was prior to the slowdown, even though I can't even get anything close to my original speed.Fully detailed version: About a week ago, my download speed decreased from 2 megabytes/s to about 50 kb/s. Prior to the speed decrease, I did not install or update any programs, so it's probably not an interference from some wayward program. I've likewise not encountered any suspicious activity on the computer, nor have I visited suspicious sites, so it probably isn't a virus either. There are several odd things, however. While my download speed has dropped so dramatically, my upload speed is exactly the same. According to a Speedtest.net check from August, my download speed was 8.5 mb/s and my upload speed was 4.14 mb/s. Currently, it is practically the same, at 4.09 mb/s. What is really strange, however, is that according to the Speedtest from today, my download speed is 9 mb/s, even though I can still not exceed 50 kb/s.I tested IDM (download accelerator) on some of my skydrive files, since download accelerators allow for multiple streams of data simultaneously. I was able to download around 500 kb/s, which is still not even close to what I used to be able to reach from skydrive with IDM before (~2000 kb/s), but still much higher than if I only used one download stream (~50 kb/s).
Additional info: Browsing speed and video streaming is also much slower than usual.
I made a new connection with a password. And I have deleted the old connection on the "Manage wireless connections" But the old connection still appears on the Wireless connections. I don't want my neighbors to connect to the old one since it has no password, and I can't figure out how to delete it.
I have installed some 3rd party software for email messaging and it requires SMTP details. I hardly even know what SMTP is. Via google I found one it has something to do with server for sending email messages but I don't want to use SMTP of my ISP which is (referring to smtp and not isp) the one that is being used in microsoft outlook program. But the 3rd party software is different one. It requires FIVE (5) datas and I have no idea how do I find them out:
email server name password username port
I have been searching for some smtp details what to type with the following requirements:
- smtp must be free to have and use details - working one - as fast as possible - no particular limits
The program also offers to set up ''in-build'' smtp server. If I choose this it works but the message cannot be sent for unknown reason. I don't have firewall and I double checked nothing is wrong with avast antivirus. So I will have to get the smtp details with mentoined four requirements. Don't even know where to search. I found some freeware smtp (or virtual smtp) applications but I need 5 datas to type in and not an application. No idea where to get them. I tried gmal [URL] but its not working, been trying also different ports.
Iam joining sky in the coming week and will be receiving their free router (G Router). I am currently using (Belkin N Router) due to the distance from my computers and interferance (eg , walls, 4 floors).
I understand that I cannot use my own router with sky because they have username & password built into router. I have heard rumours that these details can be extracted.
I am looking for a way to hide all that information that can be retrieved about me, for example browser, OS, resolution, location, etc.. Is there a way to prevent the sites from getting that info?
Is it possible to obtain details for computers that are connecting to my wireless network? I can see their mac and ip addresses. I want to get details like computer name, operating system and other details if possible.
how do i telephone / email at & t or verizon to purchase wi-fi service ? i'll go back to their website (s) mess if i can't find a phone # or email address;telephone number ? do you know any for verizon or at&t or email address?
I know that when you surf the web, websites can log your IP & MAC address.If you get my jist, I don't want my laptop to be flagged on a few web sites I have been on.My plan is to use another pc, that has a wireless braodband dongle from a mobile phone company.The pc will be attched to the wireless router via eithernet, but banned from access the web via the router. This way I can connect remotley from my laptop.
Cant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description StateNotNormalDevice IP x.y.z.1Device Type Switches and HubsFault Last Updated At 06-Nov-2012 16:12:49Component
I was handed a firewall ASA 5520 but without external flash, I want to confirm that the ASA at least boot from rommon mode boot must have the external flash connected? I connected to power and I connect it by the console port it did not show any boot.Additionally I can confirm it is possible that you can connect a flash of a previous ASA model, say a 5510?
Before I purchased the E3200 yesterday, I contacted Cisco Sales support and asked specific question about SNMP support on E3200. I was told that E3200 does supports SNMP.. However, I do not find any setup / nor any documentation on how to. Does E3200 supports SNMP? I would like to monitor my router using SNMP traps.
I know that when you surf the web, websites can log your IP & MAC address.If you get my jist, I don't want my laptop to be flagged on a few web sites I have been on.My plan is to use another pc, that has a wireless braodband dongle from a mobile phone company.The pc will be attched to the wireless router via Ethernet, but banned from access the web via the router. This way I can connect remotley from my laptop.