how do i telephone / email at & t or verizon to purchase wi-fi service ? i'll go back to their website (s) mess if i can't find a phone # or email address;telephone number ? do you know any for verizon or at&t or email address?
View 1 RepliesI have a Belkin aigo True Mimo PreN Router model FD 582304. I am trying to wireless connect a new laptop on windows 7. It wont accept the WEP key I have previously used. The router is cable connected to my desk top computer. How do I find out the details of the WEP key for this router or reset all.
View 5 Replies View RelatedI've just received a Cisco 1801W router (pre-owned), which I'm going to be installing in our school, and I have been unable to figure out the details of the wireless configuration.The 1801W router is replacing an old basic Linksys WAP54G router. I'm hoping to configure the 1801 for basic DSL, with the WiFi configured with a single SSID, using WPA-PSK authentication with a hard-coded pre-shared key on the router. We do not have a radius server available at the school.
I think I have the router set up properly for DSL with NAT and DHCP for the internal network (192.168.1.x). The router's E0 interface uses 192.168.1.1, and the dialer0 interface will receive an IP from the service provider (ISP). The only thing I'm missing is the wireless configuration part.
How can I find my wireless security key on my Verizon router
View 2 Replies View RelatedI have installed some 3rd party software for email messaging and it requires SMTP details. I hardly even know what SMTP is. Via google I found one it has something to do with server for sending email messages but I don't want to use SMTP of my ISP which is (referring to smtp and not isp) the one that is being used in microsoft outlook program. But the 3rd party software is different one. It requires FIVE (5) datas and I have no idea how do I find them out:
email
server name
password
username
port
I have been searching for some smtp details what to type with the following requirements:
- smtp must be free to have and use details
- working one
- as fast as possible
- no particular limits
The program also offers to set up ''in-build'' smtp server. If I choose this it works but the message cannot be sent for unknown reason. I don't have firewall and I double checked nothing is wrong with avast antivirus. So I will have to get the smtp details with mentoined four requirements. Don't even know where to search. I found some freeware smtp (or virtual smtp) applications but I need 5 datas to type in and not an application. No idea where to get them. I tried gmal [URL] but its not working, been trying also different ports.
Iam joining sky in the coming week and will be receiving their free router (G Router). I am currently using (Belkin N Router) due to the distance from my computers and interferance (eg , walls, 4 floors).
I understand that I cannot use my own router with sky because they have username & password built into router. I have heard rumours that these details can be extracted.
WHY ON EARTH DO SKY ONLY SUPPLY G ROUTERS
I am looking for a way to hide all that information that can be retrieved about me, for example browser, OS, resolution, location, etc.. Is there a way to prevent the sites from getting that info?
View 2 Replies View RelatedIs it possible to obtain details for computers that are connecting to my wireless network? I can see their mac and ip addresses. I want to get details like computer name, operating system and other details if possible.
View 2 Replies View RelatedHow do I find out my ISP and ISP password?
View 1 Replies View RelatedI know that when you surf the web, websites can log your IP & MAC address.If you get my jist, I don't want my laptop to be flagged on a few web sites I have been on.My plan is to use another pc, that has a wireless braodband dongle from a mobile phone company.The pc will be attched to the wireless router via eithernet, but banned from access the web via the router. This way I can connect remotley from my laptop.
View 5 Replies View RelatedCant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
Wi-Fi pin. I lost my details on the laptop. My laptop is Inspiron N7110.
View 1 Replies View Relatedwebpage error details object required
View 1 Replies View Relatedhow to get details of any destination location through google earth?
View 4 Replies View RelatedI know that when you surf the web, websites can log your IP & MAC address.If you get my jist, I don't want my laptop to be flagged on a few web sites I have been on.My plan is to use another pc, that has a wireless braodband dongle from a mobile phone company.The pc will be attched to the wireless router via Ethernet, but banned from access the web via the router. This way I can connect remotley from my laptop.
View 8 Replies View RelatedThe version of my DIR-655 is 1.32NA. Entries in the column of Time for LOG DETAILS are incorrect. How can I correct them?
View 3 Replies View Relatedbought a second hand laptop but all previous owners details are still in. they must have been on a dial-up network want to change to broadband,how? also need to sort out wifi.
View 1 Replies View RelatedI have a rather specific and annoying problem with my router. every few days or so the internet will cut out. However, i am still able to use websites that i have been using already, so am able to check emails read articles etc, but am unable to do things like stream videos from youtube or play online games. I run network diagnostics (Windows 7) and receive the error: Your computer appears to be correctly configured, but the device or resource (samsung.msn.com) is not responding. I have already updated all my drivers and have completely reinstalled my router and checked all cables etc. This appears to be only to do with computers that are connected wirelessly, as the pc connected via ethernet seems to be unaffected,
I have both a netbook and a gaming pc connected wirelessly.
Netbook:
OS Version: Microsoft Windows 7 Starter, Service Pack 1, 32 bit
Processor: Intel(R) Atom(TM) CPU N550 @ 1.50GHz, x64 Family 6 Model 28 Stepping 10
[Code].....
I have a Time Warner modem/router. There are a ton of different devices constantly being connected/disconnected to our router - itouches, computers, smartphones etc.
The problem started with my otherwise super reliable HP g42 (i3) laptop. Nothing would solve the issue other than recovering it back a few days to when the issue wasn't happening. But then it would happen again after a few days. All other devices would connect without issue.
Time warner's technical troubleshooting consists of "unplug the router for 10 seconds and then plug it back in. Did that work?"
So now, my son gets his first computer and I bring it home last night. Also an HP (pavillion -i3). Same deal. At first, it connects fine and dandy. Then after about 2 hours it get the ol' "won't connect - diagnose the problem?" After diagnose, it says "DNS server may not be available.
Here's the thing: Both computers connect immediately and without issue to my smartphone wireless tether.
I am running a Dell Inspiron 530 with Windows XP SP 3. My computer is displaying cannot aquire network address, can't contact dhcp. I have already had the modem and ethernet cables tested, they're fine, and I have tried replacing the network card, no luck. I have also run ip config renew and replace as well as ipconfig/all everything was zero. I checked the startup menu and all the appropriate network apps are marked started and automatic.
View 11 Replies View RelatedIf I loose bookmarks on my Browser, can I contact my ISP for a log to my internet history?
View 7 Replies View RelatedWe are running a ASA5520 with system image of "disk0:/asa843-k8.bin". I'm also running ASDM ver: 6.4(7)So my question is while I'm in the ASDM on the configuration of the firewall, I'm looking at the Access Rules. When I do a show log on any of the rules that have hit counts on them, it opens up a Real-Time Log Viewer but I don't see any information. It's not showing anything, nothing appears, it just sit's there like it's waiting but no data is coming. Even though if I go back out to all the rules, I can see the hit count incrementing. The same thing happens no matter which rule I pick with hit counts on them.
View 1 Replies View Relatedone of my customer has CSACS & has bought CSACS-5-BASE-LIC, at the time of registration i ,had put the end customer as my company, how to change the end customer details on the license.
Had sent a mail to licenseing@cisco.com, they changed the end user details at there end, but the same is not reflecting on the physical box at the customer site.
Running the newest firmware available
$ show version
SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
This is how I can cause the reboot to happen every time.
$ show lldp neighbors GE 10
Device ID: <mac address>
Port ID: 22
Capabilities: Bridge
[Code]....
I am looking for for details meaning of license because I cannot found the details install. The license call
FLASR1-FW-RTU(=)
that is used to enable the firewall function in ASR 1000 series. But I don't clear about what feature inside, it is because it only show the "firewall" from website. Is that same as IOS firewall?
Looking to set up a wireless printer (HP Deskjet 3050 All-in-One Printer - J610a) for use by another computer on the network; at present the printer is wirelessly connected to the router (Linksys e1000) and the software is installed on one computer (Win 7). The router recognizes a Network printer but no details about type.
The printer works correctly with the Win 7 machine but can't be found by the other machine (Win xp). Could it possibly be that I need to install the same software on the Win xp computer in order for it to be connected? Just guessing here as that was the case with another printer I networked but it was a Canon brand.
(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.
I have tried to contact this site about purchases and I can not get them to return any emails. They have a contact us link on the page
View 3 Replies View RelatedI've been trying (in vain) to connect a USB Wireless device to be able to use it off my wireless network. I have (2) other laptops and (1) other desktop connecting to the router with no issues. For some reason, this old desktop keeps installing an Ethernet device (probably on the MB) and is automatically Configuring the IP address to that instead of the USB wireless device.I've tried uninstalling the Ethernet device but it comes right back after I do a reboot. Even when I disable it, I still can not connect with my Wireless device.
View 14 Replies View RelatedOn one of our N7K, we have some packets dropped by the COPP policy in the class-default class-map. Partial results of "show policy-map interface control-plane" not so long after clearing the counters : [code]
what traffic is dropped by the policy ? Is there any logging possible ?
need to know why I can not connect to the internet after I am done downloading windows Xp on my Desk top. I got an error message from the cmd, saying that computer is unable to contact DHCP server.
View 1 Replies View RelatedCannot delete old groups in my contact list
View 1 Replies View Relatedin my network i got a switch with 4 vlan's configured
-vlan 10
-vlan 20
-vlan 30
-vlan 40
in vlan 40 i have my domain controller for my existing domain.i have read that seperate vlan's can't have contact without a lollipop router ( router on a stick, inter vlan routing)i want that users in vlan 10, vlan 20 and vlan 30 can have access to my domain controller in vlan 40
but they can't have access to each other.