Every so often (random amounts of time) my internet setting either on the router or pc change and then I it comes up with an error that my settings aren't the same as my router... I use a Orange Live box and windows 7. also when I want to sign into games for windows that sometime crashes the internet and on DOW2 and minecraft.
View 10 RepliesI have a RCA modem from comcast high speed internet.Also have a Linksys Cisco Wireless-N Gigabit Router model # WRT310N V2. When I connect the internet directly into the computer, I get download speed up to 21.07 mbps and upload speed of 3.07. When I connect through the router download speed 1.31mbps and upload speed of 1.01.I have no clue how to make changes to the router.
View 19 Replies View RelatedI have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies View RelatedI installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
I had a disaster occur on my "guest" OS within VMware-Player. I had to start over from scratch! I am back in business, except for having the virtual machine recognized by my existing wireless network. The other two computers still communicate.I went through the wireless setup routine for the new VM. A new "ID" was assigned. Obviously, this is different from the one currently in use on the network. I have the settings info on a flash drive. Can I simply insert the FD in the other two computers and have the new ID replace the existing one?
View 14 Replies View RelatedAfter changing these NIC settings I am no longer able to connect to the internet:
checksum offload -> disabled
speed/duplex -> 100 mbps full
I tried setting it back to what it was before to no avail:
checksum offload -> Rx and Tx Enabled
Speed/Duplex -> Auto Negotiation
I'm still able to ping URLs and IPs, but cant get to any websites or even the modem page. I tried rebooting,power cycling...nothing works so far.
I need to change my DCS-942L camera settings remotely when I am not connected to my home wireless network. When I am at home, I just type in the local IP address of the camera (192.168.0.100) into my browser to access the firmware. How can I do the same when I am away from home and obviously not connected to the local WiFi?
View 1 Replies View Relatedbought a second hand laptop but all previous owners details are still in. they must have been on a dial-up network want to change to broadband,how? also need to sort out wifi.
View 1 Replies View RelatedI have an Ubuntu 10.04 and basically I would like to achieve this:When I am at home, switch the network to use static IP.When I am at the office, switch the network to use DHCP.
Is there a program to do this?Or is this something that should go inside an init script where if it is weekend or weekday from 7 pm to 7 am, then consider it a home. If it is home, then use static IP.?
When I change a setup setting and click save settings, most of the time it gets stuck on the "saving..." notification window and eventually I get a "Internet Explorer cannot display the web page" notification. However I have found that if I repeatedly try it eventually it will accept the change. This never happens using the wizards only making manual changes. I am running the camera with a Wi-Fi connection. I am not sure this is a router or camera firmware bug (running V1.12)
View 4 Replies View RelatedI am working on installing a new 2500 Controller with 2 AIR-LAP1242G's attached to it. I have both registered and on the controller but I am having trouble moving one of them to a new IPS AP group that I created. Furthermore, I noticed the default gateway is missing from the static ip settings and I am unable to add that as well. When I add the default gateway and hit apply, the controller does nothing. Same thing for when I try to change my WIPS device to monitor mode.
A couple other things that I noticed is that when I go to AP groups and try to remove the AP's from the default group, there is no remove button when you go inside the default group like I see when i go into my IPS group.The AP's are on software ver 12.4(23c)JA3 Boot ver 12.4.13.0 and the controller is at 7.0.22.0I have already power cycled the controller and both AP's.
i am willing to know that how we will refresh our WAN IP's dynamically.
View 3 Replies View RelatedI am trying to configure a router with a satellite connection. I am following a HughesNet guidline. At step four after typing in the required IP address , nothing happens.There is no place to type user name and password.
View 2 Replies View RelatedI just reset my router to the factory settings in order to make some changes to it. However, when I tried to change the SSID to a unique name, I was unable to connect my computer to the wireless network. I then reset my security settings and left the SSID to the default name "linksys_SES_54125" and it is working just fine. I tried to connect with two separate computers both running Windows 7. My router is the WRT54G v8
why I wouldn't be able to connect to my wireless network when I change the SSID?
I need the capability to log into the 3g/4g modem and change the Wan IP address. Doe anyone know of a 3g/4g modem that allows you to do that. My other option would be to disable the wireless radio on the 3g/4g router and connect my Linksys Wireless router that I know I can log in and change the WAN Ip. It looks like to me that this model below would allow me to do that?MBR1516 Will turning off wireless radio on the 3g/4g router completely turn off all routing or could there be a conflict with my Linksys wireless router?
View 6 Replies View RelatedI've finally gone and done it. I phoned up aol and requested my MAC code.With my new ISP ( possibly ZEN ) if I keep my existing netgear router, can I keep my wireless connection settings the same i.e. network name, wep key etc.If, on the other hand I get Zen's router which is pre configured, I would need to set up the wireless again. Could I still use the same network name and wep key, or would I have to chose new ones.
View 3 Replies View RelatedI have a private minecraft server running off an old computer in my house. i recently had trouble, i was unable to connect. after some investigating, i found that my router changed the servers internal ip, and as a result i had to re-forward all the ports. a short while later, i rebooted the server, and its internal ip changed again. first is was 192.168.1.103, but then it went to .129, and now its .137. how can i stop it from doing this? ive never had this issue before. its a cisco linksis e2000
View 3 Replies View RelatedI need to CHANGE the password of my netgear router.
View 2 Replies View RelatedA client was having some email issue and was requested to change the 1841's LAN and WAN interface MTU to 1400 bytes. i've used 'mtu' command but was rejected and got an error like to one attached. so i used 'ip mtu' instead to make the change.
What's the difference between the 2 commands and if this would achieve the said change. I've checked using the show interface it's still showing MTU of 1500 bytes.
We are upgrading our dsl to cable. We have a cisco 877 router/dsl modem and windows sbs 2003 r2. May I know how do I change the ip addresses in the router, and how do I add a cable modem to the router?
View 1 Replies View RelatedI have a new SMART T.V. I have no trouble hooking up wirelessly to my N300 router, I can get on the internet without any problem. Then I added a wireless speaker system, now the T.V. won't hook up to the router any more. My question is, how do I change channels on the N300 DIR 615 router so that I can get away from the interference caused by the wireless speaker system?
View 3 Replies View RelatedI recently set up my DIR-615 on my wireless netbook. Everything worked fine and I could get online. But then when I changed the password on the router, it bumped me off and now says Internet isn't available. My phone can connect to Internet but not my netbook anymore. When my netbook tries to troubleshoot it keeps saying "problems with router and adapter."
View 1 Replies View RelatedHow to change the password on a 861-W router. When it was set up cisco did it.
View 9 Replies View RelatedModem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.
View 1 Replies View RelatedHow do I change the channel on my Linksys WRT54G2 ROUTER?
View 3 Replies View RelatedI want to change password in my EA2700 but don't know how to do it. How to change password in EA2700?
Looking for [url]
Find the best [url]
I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies View RelatedI recently bought a tenda w548d Version 2.0 Adsl2+ Modem router. it worked fine with its default settings and wired connection was ok when i chose DSL uplink while installing its driver from CD. But it couldn't connect wireless. There were strong signals but connected computer couldn't get access to the internet. so i tried using ethernet uplink instead of DSL uplink while reinstalling the software Since then the light of ADSL never lights, even it never blinks. now the software on the cd can connect to the router. i cannot access its settings using IP address in browser, the page wouldn't load. I am so worried. Can i revert the setting back to dsl uplink?I can connect to the internet very smoothly using my old router so you can't blame my phone line or lan wire. I have tried reset the new router many times but still the ADSL light never lights up. And the ADSL light is ok because when i turn the router on, it lights with all the others.
View 2 Replies View Relatedchaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies View RelatedI'm using the Linksys WRT160N V3 for testing a few ambedded applications.I need to set the speed of operation of the router to 100Mbps. (or at least find out what speed it currently supports) I looked up the router home page and couldn't find anything concrete.
View 3 Replies View RelatedMuch of the time my wireless printer is offline relative to computers on my LAN because the IP Address has been changed to some value different than what the computer thinks it should be. So I have to figure out what the IP Address is of the printer then modify the printer port on the PC to point to the correct address. If this only happened rarely or if I could easily remember the steps I have to take to remedy the situation, I guess this would not be such a big deal. But it happens a lot and I'm old and alzheimery. So my question is: how do I get the router to assign the same IP Address to the printer all of the time?
View 2 Replies View RelatedIs it possible to change the look of welcome page (guest login) to change so that it is personal. Of course it would be great if the guests have to log on your personal page.On this page you would be able to indicate the rules and and limitations. It would also be a good option for certain that your guests a limited time duration for the connection and gives max download. This would also be found to be in a log.
View 2 Replies View RelatedI have a WTR160N-RM. I just moved and the cable technician hooked it up unsecured. I didn't catch it until he left. I can access the Linksys webite with the standard IP address and generic password, but I'm not sure what needs to be changed. I've looked at several UTube videos and read some online instructions, but they all different a bit. How I can secure my wireless again? I have an old Toshiba LT that just keeps on tickin'.
View 7 Replies View Related