Protocols / Routing :: Changing WAN IP On 3g / 4g Router?
Feb 6, 2013
I need the capability to log into the 3g/4g modem and change the Wan IP address. Doe anyone know of a 3g/4g modem that allows you to do that. My other option would be to disable the wireless radio on the 3g/4g router and connect my Linksys Wireless router that I know I can log in and change the WAN Ip. It looks like to me that this model below would allow me to do that?MBR1516 Will turning off wireless radio on the 3g/4g router completely turn off all routing or could there be a conflict with my Linksys wireless router?
I recently bought a tenda w548d Version 2.0 Adsl2+ Modem router. it worked fine with its default settings and wired connection was ok when i chose DSL uplink while installing its driver from CD. But it couldn't connect wireless. There were strong signals but connected computer couldn't get access to the internet. so i tried using ethernet uplink instead of DSL uplink while reinstalling the software Since then the light of ADSL never lights, even it never blinks. now the software on the cd can connect to the router. i cannot access its settings using IP address in browser, the page wouldn't load. I am so worried. Can i revert the setting back to dsl uplink?I can connect to the internet very smoothly using my old router so you can't blame my phone line or lan wire. I have tried reset the new router many times but still the ADSL light never lights up. And the ADSL light is ok because when i turn the router on, it lights with all the others.
I have a CANYON Wireless N Router CNP-WF514N1A. It was working properly, but I changed its deafult password to my own . (192.168.0.1 -> wireless security -> new pass -> okay -> reboot computer ). After I restarted the computer, the router stopped working. The lights on it are fine, and if I plug the net cable into the computer I have internet too. The problem is, if I plug the cable into the router, I don't have internet. And I can't open 192.168.0.1 either.
well i had the same problem because i got bored and i was like hmm i wonder if i can change my IP and i tried it and i had the same problem but when i did system restore it still did not work, now i have to get a new operateing system...
See attached diagram, which shows me using the tp-link router to protect my internal network from the guest network for internal security.Should I put the tp-link router into a DMZ on the first main Orcon router to be able to make remote access form the web into my network? I have an IP camera etc that I need to access from the WWW. If I do this does this have any security implications; both for my network or the guestsMy reasoning is not; as the TP-Link still acts as my firewall and the specific address of the TP-Link doesn't affect the guest, but I thought I'd check with the Pros!?
I have a pair of data center core 6500 is running a single EIGRP AS with the standard core redundant cross connects. Recently an SVI sub net was expanded from a /24 to a /23 and dropped out of the EIGRP routing table. Subsequent trouble shooting lead to the router id being one using an IP address that is no longer active IP address.
Reviewing old configurations I found, that year ago, the ip address used for the EIGRP router-id (10.100.106.3) was removed from the active interface and changed but the EIGRP router-id was not updated. The switch has not been rebooted since, no loop back is configured and there is not a higher IP configured on an active interface. Reviewing documented material on it, I cannot find anything specific on this condition but do see in the discussions on duplicate IDs, that new route updates can be a problem. I know how to update the router id but I am looking for confirmation on what would be the impact when I add a new loop back and manually configure the router-id under the EIGRP process with the new loop back IP.
My assumption is an EIGRP update and route re convergence with the standard 90 seconds of outage. How to confirm this is assumption is correct? I have no test bed to find out myself without doing this on the active cores.
show version Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2) show inventory NAME: "WS-C6504-E", DESCR: "Cisco Systems Cisco 6500 4-slot Chassis System"PID: WS-C6504-E VID: V01, SN: <deleted> NAME: "1", DESCR: "WS-SUP720-3B 2 ports Supervisor Engine 720 Rev. 5.3" PID: WS-SUP720-3B
I was in an online game with my wife when I lost my internet connection. We are on the same Lynksys wireless-B router. My pc is running win7, hers has win8. I could not reconnect but could connect if I went directly into the modem. I have Comcast cable.
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:Windowssystem32>ipconfig/all Windows IP Configuratin
The setup looks like this:I have a core swith (HP Procurve) which is connected to Cisco router ( which is ISP router).I have to create vlans and do intervlan between them and reach the ISP router.I created two vlans on HP Core Switch ( apart from default vlan 1) , vlan 99 ip add 10.110.234.1 subnet 255.255.255.128 and vlan 999 ip add 10.110.234.129 subnet 255.255.255.128,vlan 1 ip add 10.110.232.42 subnet 255.255.254.0.tagged the ports of vlan 99 and vlan 999 in vlan 1. I am able to do intervlan routing, but i cannot reach router which is 10.110.232.1 subnet 255.255.252.0.I tried these scenrio on packet tracer, it is working fine.
I am just confused over the fact that a router configured with 10.1.1.1 address (assuming it's got 255.255.255.0 mask) can communicate to a PC connected to one of it's LAN ports and manually setup to have 10.1.1.2/8 address. I was sure that since these are two different subnets they won't see each other. But they do and searched wiki and just googled to see why, but with no success. A friend of my friend says something about 'same range' but it makes little sense to me.
I just need a good article about it or a crystall clear explanation, because I feel my understanding of IP is not as good as I used to believe.
I have att dsl and they supplied me with a modem, a motorola model type 2210, and my belkin surf N300 router is giving me issues connecting to the internet. Im pretty sure my wireless network adapter is a netgear wg311v3.The issue im having is that sometimes i can connect to the internet just fine, and sometimes i cant connect to the internet. I know it is a router issue because when i plug the modem into my comp, i can access the internet 100% fine.I also think it is not a wireless network adapter issue because i ran an ethernet cable from the router to my comp and had the same issues. There are 2 other computers on the network, one of them is a year or two newer than my dell desktop, and has no issues whatsoever connecting to the internet via the router. The other computer on the network is a Wii, and has connection issues when playing online (probly a different issue), but can access the internet no problem.
I am doing my college project(Client Server Chat Application in C#). I need to transfer all the data of my application through a VPN tunnel. I want to create a IPSEC VPN tunnel through which I can route the Data. I am low On budget I am not inclined towards buying any Hardware. So is it necessary to purchase a Router or a Network Interface Card To create A IpSec VPN.
I set up the password through WPA-PSK, the problems come up. My laptop, HP G62-465DX and my Ipod Touch can connect by inputting the passcode but the other laptop in my family, HP G72-b60us, cannot connect to the router once the passcode is set up because the laptop claims that it is incompatible with the router when it was before. Also, my wireless printer HP Officejet 4500 wireless G510 n-z does not work when the passcode is set-up.
I have recently changed my ISP and as such now have a modem router from them, however I used to have a seperate modem connected to my own router that I have already set up to have port forwarding to my CCTV, DVR and networked storage (Built into exsistine router).Since connecting the new modem router to my exsisting router I have been unable to access the CCTV, DVR and Storage from outside my LAN.
I guess this is because the devices are on the client list of my old router and not on my modem router.Is there anyway I can access the old port forwards through the new modem router, it used to be a matter of just xxx.xxx.xxx.xxx:9966 for example but now this would try to access the modem router and not the router it's connected to.
I have not found any options to disable the router side of it to make it act as just a modem.The hardware is a Virgin Media Super Hub model connected to a D-Link Dir-685.For arguments sake the IP address of my D-Link is 192.168.0.1 and the Super hub is 192.168.100.
I have a little problem with installing my new router. There were quite a lot of problems with the old smc, so I've bought a TP-Link router. I installed it just alright, it said congratulations, you have internet. I don't have though, not even on the directly plugged computer. It's kind of frustrating, since the old router is still working like before. So I plugged an ethernet cable from the old router's lan to the tp-link wan and with that, the new network is working just fine. The problem with the internet access occurs only, if the router is directly plugged to the modem. (The computers do find the network but the connection is kind of offline.) I don't really know what could be the problem, since I'm a little new to routers. I've read almost everything in the new router's manual and I'm pretty sure it's installed correctly. (ADSL username and password copied from the old settings, mac address copied, all ip addresses pinged, done power cycle etc..) I thought about resetting the modem, but I'm a bit afraid of losing the old router's internet connection as well.
i have a dlink-615 router and im wondering if i can configure it the best way possible to work best with wireless devices, like my laptop.there are 4computers running on my network and i want to get the best result possibly for my connection.can i change settings in the routers configuration page so 1 computer can have 90% of the signal or bandwidth of the connection.i want to decrease the other 3family members connectivity to my router, like limit their use of the network or signal/speed/bandwidth strength?
I am having a problem with my router disconnecting every time that I close a browser window. I am pretty sure that it is a problem with either my Desktop or my WiFi usb card that is connected to my Desktop. I have tested this on my laptop and it doesn't seem to have the same issue. Has any heard of this or does any have a solution to how I can get this working correctly?
I am trying to instal my Netgear router. It is asking for the Preferred DNS name and the alternate DNS name? I got the IP address and the other required fields but I'm not sure about eh DNS thing?
I'm trying to forward ports for game connections. For this particular game, I'm trying to forward port 7777My ports aren't forwarding according to: Open Port Check Tool - Test Port Forwarding on Your Router and Open Port Check Tool[CODE]
Basically I have a win2000 server running as a VM in my computer with a secondary LAN address(Different subnet) which acts as a gateway for the other devices on my network (e.g. my wifi-router has DHCP relay set to my VM's address). The VM uses another network(internal NAT) for accessing the Internet though my computer. So far, I've managed to set up the DHCP and routing. Other devices on my network have access to the internet. But, since my computer has only one NIC, and even though the VM uses a secondary IP address, it's still on the same network as my internet connection. There are computers that belong to other people, who I do not want to give access through my router(even though their computers are picked up by my DHCP). I was given only one IP address for usage on my computer. This is why I wanted to add some kind of an authentication procedure(like some sort of PPPoE login maybe?)so as to prevent unauthorized usage my my connection. The question is, 'What are my options for the authentication procedure, and where do I start?' If my explanation was unclear.
I have a problem with my Belkin router that is ruining any online gaming experience I want to have. Any time I try to play a game on my PC, I have to deal with STRICT NAT. On my router setup page I have all security features off, UPnP is enabled, and i'm pretty sure I have my computer in a DMZ. (As far as I know a DMZ'd computer should have an Open Nat right?)When I use run>cmd>ipconfig it says my ip address is 192.168.2.2, which is the same exact thing that is in my DMZ box, but it isn't appearing to work.Does anybody have an idea how to set up a successful DMZ on a belkin router?
I have D-Link Amplifi N+600 Dual Band wireless router (Model: DIR-827) that was purchased a couple of months ago. I live in a house with a bunch of other university students so I would estimate we have about 18 devices that connect to the router such as laptops, mobile phones, and gaming systems. Every few hours our wireless router will just stop working and drop everyone's connection including the connection to the wired Ethernet ports. The light which is normally green on the front of the router turns yellow and will stay that way until the router is reset. The network still shows up on all the devices with full signal bars but no access.
i got a d-link router comming off modum and then a lynksys switch . well when i run the lorex program it (the switch) shows up as a router with a ip address ? i have tried a different swith but still the same thing happens .
I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page
i have decided to take on the 3G strategy by using some powerful equipment to boost my 3G and obtain internet access, (accessible no problem)however in my "kit" includes a huwaii mifi device which i will be using along with a crc9 to connect to my military spec booster to pick up 3G and get better internet speeds than anyone in the area.problem i have is with the mifi router, it has small wireless range.i have a strong transmitter to use with my standard router, now what i want to do is bridge the mifi with a a/g/n router and all devices connect to the router that will provide better coverage due to the 3g kit and mifi will be very close together in the roof space and away from the other devices on ground floor.can i bridge mifi with a wireless router so connections will run through the lets say, belkin router.
I have a wifi network on my college campus, but my laptops wifi does not work. But i have a spare router with multiple lan ports. Can I use it to detect the wifi signal(from campus routers) and then use a LAN wire to use the internet on my computer? I do not have access privileges to the college router other than connecting to its wifi signal.
I have my D-link DIR 600 and I never had problems with it until now. For the past three weeks, my router keeps on disconnecting my Desktop P.C. from which the main internet cable is connected. Whenever it happens, I try connecting my Netbook over a WiFi connection using the same router; and even though my desktop can not connect to the internet, my netbook still can. Apparently when it happens, the [3] (the 4th light in the image) light goes off, and I have to restart my Desktop P.C. for it to turn on again and to use the internet again.
i have a linksis WRT120N and had to call someone to fix it up to the net modem when i got it but i have upgraded the speed of my net from 256KB to 1MB and now facing the same problem.when i call the net provide they said they dont support 3rd party stuff but told me itd because of conflict between router and modem.
