i just bought a 5508 wireless controller that was delivered yesterday .I powered it on yesterday and was able to make basic configurations of management interface ,time and zone settings.I was also able to get to the GUi and console after the configs and it was alright. When I got in this morning it ran for about 2 hours and all of a sudden starts shutting down after every % minutes and comes back again.
View 7 RepliesI just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it
View 9 Replies View RelatedI've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it. All the documentation I can find mentions using the "archive" command at the command line. It doesn't appear to like the archive command.
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.
I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
I've a problem with a router 2811:
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[Code]......
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies View RelatedI have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:
Error Message %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.
but the same image works fine on another 5508.the update was downloaded via a smartnet for the wlc, on which the update works fine. does the customer has to download another image for the second controller, or should the image work on both wlc?
I started a download to a 5508 to upgrade to 7.2.110, but the connection across a vpn is slow and taking too long. Can I cancel the download w/o corrupting the current image and/or setup?I don't see a cancel button anywhere in the gui and don't want do it unless the controller will handle an incomplete download correctly.
View 5 Replies View RelatedAt the moment I have a problem with a WLC. This WLC is not booting by the fact it does not have an image. In the past option 5 in the following menu was selected.
Now I received I message when I select option 6. Telling me that if I upgrade from an .aes image I will left the unit inoperable.
============================================================
Boot Loader Menu
============================================================
1. Run primary image (Image not found)
2. Run backup image (Image not found) - Active
3. Change active boot image
4. Clear configuration
5. Format FLASH Drive
6. Manually update images
I have a WCS v.7.0.230.0 and four controllers v.7.0.235.3 (on two WiSMs). I have a problem now where when adding/modifying guest users the controller list shows only three controllers. I don't know when this started happening or why but no matter what I do (including removing the controller and adding it again) I can't get the controller list to be fully populated with all four controllers. I've attached an image of what I'm seeing.Other functionality appears to be normal, for example I can add "mac filtering" addresses to all four controllers with no problem, APs can register to the affected WLC etc.
View 2 Replies View RelatedI have a Linksys WRT54GL router in one building and a second router in an adjacent building. I have connected each router to a MODEM that takes me to the internet. Can I configure the two routers to talk to each other and at the same time maintaining their respective internet connections
View 4 Replies View RelatedI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
I have a Linksys Wireless G PCI adapter. The model is WMP54gs and the serial number MGP00E416793. I am trying to install this adapter on a Windows XP media center computer. The computer is update to date with all windows updates. I need the driver and software to successfully get this adapter to fully work.
View 3 Replies View RelatedSet up wireless internet with this computer. After going through set up wizard my computer would not fully connect to wireless. It is connected to the network but the internet does not go through. When diagnosing the problem windows says "A problem with your network router or broadband modem might be preventing an internet connection. My husbands computer and phone have no problem connecting. My computer says the wireless network adapter is working properly and I seem to have no trouble connecting to other wireless connections.
View 4 Replies View RelatedThe host computer runs Windows XP (SP3), and the client - Windows 7 Ultimate. The host computer connects to the internet with a USB wireless modem (HSUPA USB modem by ZTE). So I enabled sharing and connected the two computers with an Ethernet cable, so the first time it worked. The next time I turned on the computers I wasn't able to share the internet, I wasn't able to load any pages on the client computer, however Skype was working. I tried to use various guides on how to input IP addresses manually etc, but that didn't work, finally I felt like I had changed so much that I decided to restore both machines to an earlier point and start over, that still didn't work.
Then I bought a Cross-over Ethernet cable, and the first time I connected the computers - the internet was working on the client computer, I reboot - only Skype works.When I try to diagnose the problem on Windows 7, it usually can't find anything (it says that I have access to the Internet, but in the "Details..." it says that IPV6 has no internet access), or once it said something about IP addresses but wasn't able to fix it, the other time it said that DHCP wasn't enabled on the client computer and it enabled it and the internet started working. Right now on the client computer in LAN "Details..." it says that DHCP is disabled, but the diagnostic tool doesn't detect anything.
What numbers I should blur, when I restored, on the XP (host) computer the antivirus broke down (avast, free), so I had to uninstall it with a special uninstaller through safe mode and install it again, so when I reinstalled the internet sharing was working again, so it made me think that it was avast's fault, however there's no firewall in my free version so in avast forum I was told that avast is not the problem.
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View Relatedi have tried many things i have tried to reset my router with the cmd prompt i have checked my drivers i have tried the simple things and at this point.
View 1 Replies View RelatedI'm using a RV082 and have about a dozen users on my network.Occasionally, when a user is accesssing a website like yahoo.com, twitter.com, cnn .com, etc, the web page only loads half way. Most often the page is missing stylesheets and/or images. Called Cisco support and they adjusted the MTU size to 1492 from 1500.Have a looked at the bandwidth report from my ISP and it shows nothing out of the ordinary, no spikes or surges in d/u. Have set LAN port to high priority, 100 Mbps, full duplex.. Seeing an error count around 327282.. which I don't understand.Why sites only partially load using this router?
View 1 Replies View RelatedI am trying to configure two inside interfaces without NAT. I am not using nat-control and I have added exemptions for the two networks. I can communicate between the two networks and to the Internet just fine.I would like to verify that NAT is disabled between the two interfaces. I also need to make sure that the Interface IP (specifically for the traffic from inside-test to the inside network) is not added to packets between the two networks. I would like to be able to verify this as well. In other words I need to have the Source IP address from the originating connection on the inside-test network passed along through to the Inside network device without being replaced by the Interface's IP address. This is a test config for a production environment that will be using a load balancer. The config I have may be working in this regard and the load balancer may be replacing this IP address (that is what I am trying to test), but I am not certain.So far I have the following NAT related running-config command (in regards to these two interfaces):
access-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0access-list NAT_Exempt_2 extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list NAT_Exempt_2nat (inside) 1 0.0.0.0 0.0.0.0nat (Inside-test) 0 access-list NAT_Exemptnat (Inside-test) 1 0.0.0.0 0.0.0.0
global (outside) 1 interfaceglobal (Inside-test) 1 interface
We've put in a 3750 at our corp hq (Detroit). We did this to break up the current flat 172.16.0.0 /16 network into separate VLAN's for various purposes. We plan on doing that at another site (Farmington), which will become a DR site. We are running EIGRP throughout the organization over an OPTEMAN netowrk and also sending routes to a managed MPLS network which uses BGP. BGP redistributes into EIGRP and vice versa. I've attached a pdf of the network. The 3750 core at the corp hq is a temp core, hopefully upgrading to Nexus within a year or two. This problem didn't exist until the 3750 was introduced and became the gateway for the site. The OPTEMAN router was the gateway and was on the same VLAN as the MPLS router.
So, in detroit we have an Detroit-MPLS router, Detroit-3750, and Detroit-OPTEMAN. What I'm seeing is that the routers I'm getting from the MPLS router make it to the 3750. The 3750 advertises those routes to the Detroit-OPTEMAN router. However, the OPTEMAN router doesn't advertise these routes any further..
In Farmington, it is currently set up like Detroit used to be set up. There is a flat network and both routers are on the same VLAN, no L3 core switch. Routes come in from the MPLS, get advertised to the Farmington-OPTEMAN router, distributes the routes out to all OPTEMAN connected routers, including Detroit. However, Detroit is not passing that route to the 3750.
When we made the 3750 stack the core, we didn't change anything else, except for some IP changes. Why these routes aren't fully redistributing?
Detroit-3750 Stack
WS-C3750G-24TS-S <-Stack master running c3750-ipservicesk9-mz.122-55.SE7.bin
WS-C3750X-12S-E <-Running c3750e-universalk9-mz.122-55.SE7
show sdm prefer
The current template is "desktop routing" template.
[Code]...
My computer (running windows XP and connected to the internet with a D Link USB adapter) refuses to load any webpages: despite showing full signal strength and connection in both the D Link settings and the windows XP wireless panel.I am able to ping websites and other computers in the house (all of which are able to access the internet) but no pages load in any browser I try.
View 1 Replies View Relatedlet me know the exact meaning of attach ( yellow marked one)? the contractor was saying "it doesn't mean two switches as there is a built in redundancy in Cisco switch)"I don't think he is correct as I never heard about built in redundancy in Cisco Router/switchAny comment as this will affect the numbers from 55 (3750 v2) to 110....
View 41 Replies View RelatedWhat is supported in terms of running a mixed feature set in a Cisco 3750 switch stack.We are looking at setting up a stack consisting of 5 x 3750V2 and 2 x 3750G. Due to a requirement for full EIGRP we need the IP Services feature set. Is it a supported configuration to run with 2 or 3 switches running the IP Services feature set as stack masters and the others running IP Base? I understand that if stack master priorities were set these switches with the higher feature set could manage the stack and offer IP Services accross the stack. If we were to lose all of the switches running IP Services the stack would drop back to IP Base.I am looking for guidance as to if this is a supported configuration and not in breach of licensing? Is this likely to cause any problem other than above now and for future IOS releases?
View 2 Replies View Relatedwill not load on my computer but will work on others
View 1 Replies View RelatedWhen have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]
View 2 Replies View RelatedWe have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...? Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.
View 3 Replies View RelatedMy wireless connection says i have full bars of signal. When I do a speed test, i get 500-600 kb/s download. Which is what I used to get. However, after I re-installed my wireless adapter's card, the wna3100 netgear, it became extremely slow.
Pages would load slow, I could no longer play League of Legends properly because the ping is too high. Also, I used to have crossfire graphics cards running and the internet was fine, but after reinstallation, I thought I'd turn it off because that's how I fixed it before. But now, even with just one graphics card running, the internet is extremely slow.
[code]...
Having troubles loading a certificate in System security/802.1X Supplicant. I tried to upload *.car and *.msc certificates, but the device aborted the upload at each attempt.
View 2 Replies View RelatedHaving problems with the E1200 when it comes to loading images and vidoes. Text loads fast, but images take several minutes, and for videos - forget about it, takes at least 15 minutes to load even a 2 minute video. I've changed MHz settings and several other settings, but nothing seems to have worked.
View 1 Replies View Related