Cisco Wireless :: AP Unable To Download Image From 5508 WLC?
Apr 26, 2012
I have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
View 10 Replies
ADVERTISEMENT
May 8, 2012
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies
View Related
Jul 15, 2012
I started a download to a 5508 to upgrade to 7.2.110, but the connection across a vpn is slow and taking too long. Can I cancel the download w/o corrupting the current image and/or setup?I don't see a cancel button anywhere in the gui and don't want do it unless the controller will handle an incomplete download correctly.
View 5 Replies
View Related
Apr 1, 2013
% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
View 12 Replies
View Related
Jul 25, 2011
i just bought a 5508 wireless controller that was delivered yesterday .I powered it on yesterday and was able to make basic configurations of management interface ,time and zone settings.I was also able to get to the GUi and console after the configs and it was alright. When I got in this morning it ran for about 2 hours and all of a sudden starts shutting down after every % minutes and comes back again.
View 7 Replies
View Related
Jun 17, 2012
one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:
Error Message %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.
but the same image works fine on another 5508.the update was downloaded via a smartnet for the wlc, on which the update works fine. does the customer has to download another image for the second controller, or should the image work on both wlc?
View 3 Replies
View Related
Sep 4, 2011
I want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
View 1 Replies
View Related
Jun 23, 2011
I have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Apr 14, 2011
I have an ASA 5505 VPN router w/ 10 license seats.I want to update the software image using ASDM. url...
View 4 Replies
View Related
May 25, 2011
I upgraded my WISM software to v. 7.0.116.0. The upgrade went smoothly. Most of my WAPs are H-REAP and they are working fine. I have a few local mode WAPs that are stuck in a downloading state. They will try to download, reboot, then try to download again. This is happening only with the WAPs in local mode. These WAPs were working before the upgrade.
View 2 Replies
View Related
Sep 13, 2011
download an autonomous image for Cisco Access point 1242 ?
View 1 Replies
View Related
May 8, 2013
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Image Download N2K-C2232TM-E-10GE
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Offline N2K-C2232TM-E-10GE
[code].....
View 6 Replies
View Related
Mar 18, 2012
I have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies
View Related
Oct 23, 2012
At the moment I have a problem with a WLC. This WLC is not booting by the fact it does not have an image. In the past option 5 in the following menu was selected.
Now I received I message when I select option 6. Telling me that if I upgrade from an .aes image I will left the unit inoperable.
============================================================
Boot Loader Menu
============================================================
1. Run primary image (Image not found)
2. Run backup image (Image not found) - Active
3. Change active boot image
4. Clear configuration
5. Format FLASH Drive
6. Manually update images
View 1 Replies
View Related
Apr 16, 2012
I know it is possible to create custom web auth splash pages on the WLC 5508. Is it also possible to embedd a small document (less than 1MB) that users can download directly from the controller? I need this for providing the terms of use for the Guest WLAN.
View 3 Replies
View Related
Feb 14, 2012
We recently did a forklift upgrade on our campus and installed 3502i's, 3502e's, and 11 5508 WLC's. Our students are complaining about slow connections in several areas of the campus.In our testing and basic trouble shooting our Apple laptops have no problems but our windows laptops are showing a very slow connection rates 264kbps downloand and 366kbps upload. The window device has current drivers installed.
View 14 Replies
View Related
Mar 19, 2013
I want to download the Cisco 2500 Series Wireless Controllers Release 7.3 Software AIR-CT2500-K9-7-3-112-0.aes.I have CON-SMB for it, when I try to download it I am not to download it. I have mentioned the message given by Cisco" The category for this contract does not include the feature or the benefit for software download that you are requesting at the moment, this means that even if the contract is a support assistant (8X5XNBD) does not support the the mentioned feature for you to update the device you need, please refer to your partner directly to be able to acquired a Cisco Service Contract that supports and include the software download feature to be able to upgrade and update your device as you need."Is there any seprate contract for downloading the Software.
View 2 Replies
View Related
Feb 28, 2011
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
View 1 Replies
View Related
Nov 30, 2011
I recently add a second CT5508 to the network, but when I tried to add the first 5508 to the mobilty group I received a message like this:
"error in creating member"
I've tried different mobility names, via GUI, via CLI and always the same error.
I've verified twice or more than twice connectivity issues or any error on the entering the MAC and IP of the controllers, everything is fine.
I'm using version 7.0.116.0
View 4 Replies
View Related
Jan 10, 2013
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
View 11 Replies
View Related
Aug 20, 2012
I had configured a Cisco 5508 series WLC. The APs used are Cisco 3502 LAP. The APs are configured to use DHCP for this ip addresses.
We had configured the DHCP server on the 2 Windows AD server previously and the APs were not able to get an IP address when the WLC was rebooted. To isolate the cause, we configured the DHCP server on a cisco 6500 switch. When we reboot the WLC, most of the APs are not able to grab an IP address. We had to remove and reconfigure the DHCP pool on the cisco 6500 for the APs to capture the IP addresses.
My colleague had feedback that they gotten a message that the DHCP pool had been used up. We tried to do a "show ip DHCP pool" but the switch did not recognise the command. IOS version used is Version 12.2(50r)SYS2.
We had a problem with the wireless client getting ip addresses from the windows DHCP server previously but problem was resolved after we disabled the DHCP proxy on the WLC.
What we are curious is why was the DHCP pool fully used on the Cisco switch and how could we check the number of addresses used other than running "show ip dhcp binding" and doing a count of the IP addresses?
Also why did we have to disable the DHCP proxy on the cisco WLC for the wireless clients to be able to get an IP address from the windows DHCP server?
We seem to be facing a number of problems with the DHCP functions for the wireless setup.
View 5 Replies
View Related
Apr 5, 2013
I have a 5508 wireless controller running version 6.0.199.4 (the image installed when the device was shipped) and I am trying to install by tftp version 7.3.112.0
The issue is when using tftpd32 gets to 82% transfered then fails with the error "% Error: Code file transfer failed - Error while writing output file"
View 7 Replies
View Related
Aug 20, 2012
I have a 5508 at a remote site and a 5508 at my main campus. I was doing some work on the remote site's controller, so I changed option 43 on our DNS/DHCP system, then applied an LWAPP template from NCS to the AP's to migrate them to the controller at my main campus (so users could still utilize the wireless at the remote site). They all moved over to the temporary (main campus) controller without an issue.
When I was ready to migrate the AP's back to their local (remote site) controller - I changed option 43 for each sub net that contained AP's @ the remote site to point back to their local controller's management IP address, pushed an LWAPP template again (pointing it to the local controller obviously) and apply template/reboot AP.
The AP reboots, disassociates from the main campus (temporary) controller, but when it comes back up a few minutes later - it associates BACK to the main campus controller it was on instead of to the remote site/local controller like option 43, the LWAAP template (and my frustrated screams) are now telling it to. I'm certain I'm just missing something.
View 13 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Nov 27, 2012
Guestconnect SSID configured on 5508 WLC with Pass through athentication (NAC guest server). No issue with Laptops and Iphone/Ipad ver 4and 5. Only Iphone Ver 6 users unable to access Guest connect .
View 9 Replies
View Related
Aug 19, 2012
I'm having some difficulties configuring my Cisco WLC (5508) - ver 7.0.230.0 .I'm have multiple client device residing on same vlan associated to the WLC but unable to telnet over port 8090. However, when inter-vlan, client device able to telnet over port 8090.Say Machine A as application hosted machine and Machine B as client machine; [code] i should be looking on the WLC to allow telnet port 8090 over from Machine A to B within the vlan .
View 2 Replies
View Related
Sep 4, 2011
We have two SSID's Guest and Corp. We are using 5508 controllers.
The problem is that if an iPad user is connected to Guest SSID and then try to connect to Corp then it fails saying "Unable to connect to Corp". After 10-15 retires the same iPad connects successfully. The problem doesn't happen on windows PC. I have attached debug for one of the clients.
View 1 Replies
View Related
Jun 26, 2012
Background: Wireless credit card machines can't stay connected to the 5508 controller 7.0.116 / 1142 ap wireless system. MAC address of one of the wireless hosts is 00:12:0e:ec:ce:97. AP servicing them is d4:a0:2a:99:34:60. Hosts are able to connect to the network after a reboot and stay connected for random periods of time but then don't come back unless you manually reload them. I have 3 in total in the same room services by the same ap.
I have the output of debug client 00:12:0e:ec:ce:97. Output showed 802.1x 'timeoutEvt' Timer expired for station 00:12:0e:ec:ce:97 so I increased the value to 4000ms on the controller but am still having the issue.
Note that the output below is the state the client stays in after receiving the timeout (802.1x 'timeoutEvt') showing subsequent attampts. The only way to get them back on is a reload of the credit card machine.
[Code]........
View 3 Replies
View Related
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
View Related
Jun 12, 2012
I have a 5508 WLC and 40+ LAP1142N APs spread across 19 locations that allows staff to connect to our private network via wireless. I recently deployed about 40 new laptops all identical make and model HP ProBook 4530's and all have the same client setup for the wireless. Out of those 40 laptops I have 4 that will not connect to the private network. However, these same laptops will connect to my public, open wireless network without issue. In addition to the 4 that will not connect all the others will prompt twice for network authentication.Now, I have about 10 other laptops that are not the HP model and all connect without issue and without dual propt. I don't think this is a wireless network issue but could be some type of issue with this model of laptop.
View 8 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
