I have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 RepliesI purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
I have a cisco 2821 Router , it was operating fine but for the past 2 days its having a weird problem.During operation suddenly the connection is lost and when checked through console there is no IOS image on the Router (all configuration is erased and the router boots up in rommon mode and there is no IOS on dir Flash:I installed ios on it through tftp but again after some random time the IOS is automatically erased from flash i checked the config register value and its fine at 0x2102.
View 5 Replies View RelatedI have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedI have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies View RelatedI have an ASA 5520, currently running version 7.25-k8. I'm preparing for an upgrade to version 7.25(4), so I transferred the software code (obtained via Cisco download) to the firewall vis SCP. I then issued the "verify flash:asa725-k8.bin" and it fails. It comes back with the error that the CRC did not verify, Data Integrity has been compromised". My first thought was the image did not copy correctly, so I deleted it and transferred it again. I got the same error. Then I decided to run a verify against the actual current code that was running on the firewall, and it came back with the same error. I don't understand what the problem is. I don't tend to think it's an SSH key related problem, as the method I use to access the firewall is via SSH and I have no problems. Worth noting,this firewall is part of an active/standby pair, and I observe the same behavior on the failover unit, it fails to verify.
View 3 Replies View RelatedI've had occasional issues with 5505 upgrades going south when the boot hangs on the image load due to a corrupt image. I need a way to validate the checksum of the new image after it is copied to flash. Remote upgrades become a real pain when you have to go onside just to delete an image, copy it into flash again, and boot.
View 1 Replies View Relatedmy firefox doesnot play flv in web,what do i have to do
View 1 Replies View RelatedI want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
I have a 2600 router i intend to use as an access server. I doesn't have an IOS so i downloaded via tftp. I should see the file at Dir flash:, but all i get are these error
rommon 1 > dir flash:
File size Check sum File name lseek out of bounds getdirent: lseek error rommon 2 >
And if i tried to download again the file, its failing because it seems that there aren't any space available in my flash. Here is the mem info.
rommon 2 > meminfo
Main memory size: 64 MB.
Available main memory starts at 0x10000, size 65472KB
IO (packet) memory size: 0 percent of main memory.
[code]...
Here's what i think. The first file download could be corrupted and it eats up the space on my flash. My question is how can I reformat the flash so that I can re download the IOS? And if in case that fails also, any other way i can recover this machine.
my upload speed show 3.1MB and download speed just 11 to 70KBps is there any software to increase download speed and decrease upload speed ? i use flash USB modem for net. actually i think uplaod speed is not true speed coz at Iraq they cheating alot
View 2 Replies View RelatedI successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies View Related% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
I have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
In a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies View RelatedI have an ASA 5505 VPN router w/ 10 license seats.I want to update the software image using ASDM. url...
View 4 Replies View RelatedI upgraded my WISM software to v. 7.0.116.0. The upgrade went smoothly. Most of my WAPs are H-REAP and they are working fine. I have a few local mode WAPs that are stuck in a downloading state. They will try to download, reboot, then try to download again. This is happening only with the WAPs in local mode. These WAPs were working before the upgrade.
View 2 Replies View Relateddownload an autonomous image for Cisco Access point 1242 ?
View 1 Replies View RelatedI started a download to a 5508 to upgrade to 7.2.110, but the connection across a vpn is slow and taking too long. Can I cancel the download w/o corrupting the current image and/or setup?I don't see a cancel button anywhere in the gui and don't want do it unless the controller will handle an incomplete download correctly.
View 5 Replies View Relatedsh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Image Download N2K-C2232TM-E-10GE
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Offline N2K-C2232TM-E-10GE
[code].....
A visitor wants to use his laptop but I don't know the security code to get his computer to operate on my network. How do find that code and put it on my flash drive??
View 2 Replies View Relatedi tried to create a customized web-authentication page that will re-direct any user to the web-page once they are connected to the network.
The problem is, i just cant attach/upload the image of the logo into the customized web-page (welcome/login page).Been researching about it, found and tried some clue bout it on cisco documentation, but still can't solve the problem.
Cisco document :Catalyst 3750 Switch Software Configuration GuideCisco IOS Release 12.2(52)SESeptember 2009
switch version :WS-C3750-48TS
show flash :2 -rwx 12305677 Mar 1 1993 01:27:03 +00:00 c3750-ipservicesk9-mz.122-52.SE.bin3 -rwx 131 Mar 1 1993 00:17:25 +00:00 log.text5 -rwx 3254 Mar 1 1993 00:01:01 +00:00 config.old8 -rwx 113 Mar 1 1993 03:24:33 +00:00 pass.htm9 -rwx 1088 Mar 1 1993 03:39:18 +00:00 login.htm10 -rwx 113 Mar 1 1993 03:21:30 +00:00 fail.htm11 -rwx 104 Mar 1 1993 03:25:32 +00:00 expire.htm12 -rwx 856 Mar 1 1993 00:05:19 +00:00 vlan.dat14 -rwx 2479 Mar 1 1993 01:25:05 +00:00 web_auth_logo.jpg16 -rwx 1048 Mar 1 1993 00:01:01 +00:00 multiple-fs27 -rwx 1053 Mar 1 1993 02:18:34 +00:00 webauthpage.html38 -rwx 6551 Mar 1 1993 01:19:33 +00:00 logotest.html
following is my running configuration :Building configuration...
Current configuration : 4205 bytes!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Switch!boot-start-markerboot-end-marker!!!!aaa new-model!!aaa authentication login default group radiusaaa authentication login line-console noneaaa authentication dot1x default group radiusaaa authorization auth-proxy default group radius!!!aaa session-id commonswitch 1 provision ws-c3750-48tssystem mtu routing 1500authentication mac-move permitip subnet-zeroip
[code]....
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatediI downloaded belkin n150 router where do I find network security key
View 1 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedI get on-line, and the internet all-of-a sudden starts to show that I've downloaded my limit of 250MB. Now, I am on Hughesnet for internet service, can not get on DSL, wont happen already asked. Now, I am running a router, only way my wife and son can access the internet. They have laptops windows 7 and build-in Wireless Cards. I have a desktop windows 7. My updates are scheduled in the morning hours about 5AM so their is no reason for the computer to update. Same goes for my wife and son, their are set for early morning hours as well. I get an error message as soon as I click on my webpage that I want to browse, Internet Can Not Display The Webpage or something to that effect.
View 8 Replies View RelatedFirst some info:
System image file is "flash:c800-universalk9-mz.SPA.152-4.M1.bin"
Cisco C819HG+7-K9 (revision 3.0) with 492620K/31667K bytes of memory.
[code]....
The strange thing is....I have a running-config if i ssh to it. but according to my flash: there is only my IOS.BIN. How is that working?
Where the latest working image can be found. because Cisco states the the one right now i the right..but still i cant see cellular 0 in CCP
what physically distinguished NVRAM from EEPROM (flash)? What type of memory is used for "firmware"
View 1 Replies View RelatedI am looking around hwo to know the flash and ram installed in WLC 4402? try looking any command, sh ver not there. even in WCS.
View 2 Replies View RelatedIs it possible to upgrade the flash on the 3750's? We have the older 3750 (WS-C3750-48P-S) only has 15998976bytes flash...
View 1 Replies View Related