I upgraded my WISM software to v. 7.0.116.0. The upgrade went smoothly. Most of my WAPs are H-REAP and they are working fine. I have a few local mode WAPs that are stuck in a downloading state. They will try to download, reboot, then try to download again. This is happening only with the WAPs in local mode. These WAPs were working before the upgrade.
View 2 RepliesI'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
is there a way for pre deploying the new ap images? We have around 500 APs and my inspection windows isnt long enough to upgrade via controller......
View 6 Replies View RelatedI have been having some issues trying to stand up an older WiSM that has been incorrectly configured by my predecesssor and has a bad Mgt IP so I am unable to telnet or SSH into it, nor can I console or session into it.
What I would like to do is to change the Mgt address for the WiSM controllers (1 and 2) by way of the Sup (not sure that is possible) because as it stands they are set to 169.254.1.1 and are unreachable even when directly consoled into them.
Core-A#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.2/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.3 169.254.1.1 4.0.217.0 Oper-Up
3 2 10.104.52.4 169.254.1.1 4.0.217.0 Oper-Up
Core-B#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.50 10.104.30.254 7.0.116.0 Oper-Up
3 2 10.104.52.51 10.104.30.250 7.0.116.0 Oper-Up
I hope to get this WiSM setup on Core A and get it configured like I have my Core B and then run them in a dual failover design with load balancing between the two.
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies View RelatedI want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies View RelatedI have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 Replies View Related% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
I have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
I have an ASA 5505 VPN router w/ 10 license seats.I want to update the software image using ASDM. url...
View 4 Replies View Relateddownload an autonomous image for Cisco Access point 1242 ?
View 1 Replies View RelatedI started a download to a 5508 to upgrade to 7.2.110, but the connection across a vpn is slow and taking too long. Can I cancel the download w/o corrupting the current image and/or setup?I don't see a cancel button anywhere in the gui and don't want do it unless the controller will handle an incomplete download correctly.
View 5 Replies View Relatedsh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Image Download N2K-C2232TM-E-10GE
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Offline N2K-C2232TM-E-10GE
[code].....
I have L3 switch 3560 v2 cisco switch. If i connect the switch via the console cable in XP system i am not getting any responce. I think i need to install via XY mode.
how can i install the ISO iamge via XY mode in cisco switch 3560 v2.Cisco Model: WS-C3560v2-48tS-S.
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
I got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies View Relatedi have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies View RelatedWe are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies View RelatedI need to upgrade the fwsm image from 3.1(10) to 4.0(8). Can i do it directly from 3.1(10) to 4.0(8) ?Do i need to upgrade other image also along with Firewall version 4.0(8)?
[code]....
I was trying to upload image to sup x4516 V10G from Rommon using the management port but did not succeed. The steps which I did as mentioned below: [code]I got the tftp request on the tftp server but from the switch was showing access violation
View 0 Replies View RelatedI downloaded all updates packages of the device for the Cisco View and I could not the show the image
View 1 Replies View RelatedI upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedI wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies View RelatedI have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedI own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedHow can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View Related