Cisco Switching/Routing :: 3750X 12-SFP IP Base - Upgrade To IP Services Image
Jan 23, 2013How can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 RepliesHow can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 RepliesI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 5 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 1 Replies View RelatedI'm trying to work out if I need to order the "IP services" image for a couple of C3750-X. I need to run OSPF on these switches, but find the IOS image requirements on Cisco contradict.
At the top of the data sheet it says: • Open Shortest Path First (OSPF) in IP Base image
On the product info page it says: IP Base: Enterprise Access Layer 3 Switching, including OSPF (Open Shortest Path First) for routed access
But in lots of other places it says you need 'IP services' for OSPF.
As the IP services IOS is quite a bit more expensive I would like to avoid buying it. What image do I need to run OSPF?
I would I upgrade this from a LAN base to ip services?
View 2 Replies View RelatedC3750X-24T-S have IP base SW initialy. It is possible to upgrade IP services feature set? BGP routing is needed.
View 1 Replies View RelatedI have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View RelatedI have 3750 Switch and need to activate the ipservices on it , it is need a license file to switch from ipbase to ipservices , if i installed the ipservices image from cisco site , do i still need an activation key to use it??
View 7 Replies View RelatedThe model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies View RelatedI'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies View RelatedI have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
View 1 Replies View RelatedFull feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
View 3 Replies View RelatedI am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedI have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
What is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View RelatedWhen I config BGP on my 3750X Switch, it show error as below:
protocol not in this image
should I need to upgrade the IOS or Where I can found a supported image (support BGP)
What features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies View RelatedI've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
Would like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View RelatedI am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedI wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies View RelatedI own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
i need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedI am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedThe 3750-12S-S comes with IP based IOS. I know it is possible to upgrade the IOS on a 3750X-48P-L from LAN based to IP based IOS. However, can the IOS on the 12-S be downgraded to the LAN based IOS?
View 2 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View RelatedSwitch 2 has an interface configured in RSU Standby.Switch 3 has an interface configured in RSU active. The upgrading sequence is : Switch 2, Switch 1, Switch3.The aim of the test is to prove that there is no loss of IP connectivity throught the RSU process.During the RSU process, there are ping between all the computers.
IOS starting version : 15.0-1.SE3
IOS upgrading version (with OVERWRITE) : 15.0-1.SE3 (same version)
1rst step : Switch 2 reboot and come back master but isolated from original stack (switch 1 and 3)
2nd step : Switch 1 reboot, and come back with switch 2 into the upgrading stack.
Issue : at this step :
- Switch 1 put its interface (IP 192.168.5.254) up :
- Switch 3 has not reboot and still has its interface (IP 192.168.5.254) up
=> we have some OSPF adjencies and mac flapping issues : switch 1 and 3 are trying to mount there OSPF adjencies on the same IP. We loss our IP connectivity since step 3 is not over.
3rd step : Switch 3 reboot and come back up in the upgrading stack. The IP connectivity is back, and the RSU process is done.Is that a normal behaviour ?How can we avoid to loose IP connectivity during RSU process ?
IOS upgrade tried on the stack of 2XWS-C3750X-24T-S , Upgrade was tried to support WCCP on the platform. Current version is Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE1, Not able find any IP Plus ios in the site ? Only available are IP base and Universal K9 , Tried upgrading to c3750e-universalk9-tar.122-58.SE2.tar by using stack upgrade method as per document [URL]
Upgrade fails with error :
%Error opening flash:update/info (No such file or directory)
ERROR: Image is not a valid IOS image archive.
Why current ios is not supporting WCCP , I hope it is there in the featureset. ( tried "sdm prefer routing" but no success) Does c3750e-universalk9-tar.122-58.SE2.tar will give me wccp support ? What is the issue with my upgrade and how do I do a successfull upgrade ?
I try to updgrade a stack of two 3750X-48PS to the IOS 15.0-2
Same commande has the twelves others stack I have upgrade lately
archive download-sw /overwrite tftp://x.x.x.x/c3750e-universalk9-tar.150-2.SE.tar
or
archive download-sw /overwrite usbflash0:/3750/c3750e-universalk9-tar.150-2.SE.tar (much faster!)
At the end I have this message :
extracting c3750e-universalk9-mz.150-2.SE/info (511 bytes)
extracting c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin (19842267 bytes)
[Code].....
I have upgraded my Catalyst 3750X-switches to software-version 15.0(2)SE2, but I cannot upgrade the 10G servicemodule to the same version. I use the archive download-sw command to load the c3kx-sm10g-tar.150-2.SE2.tar. The file is loaded to the switch, but when the process starts to transfer the file to the module it fails with the following messages:
Error 2: Unable to transfer image to FRU Modul on switch 1Error: Failed to update FRU Module image
The modules is now running with in-compatible versions as shown below:
Switch# H/W Status (CPU/FPGA) CPU Link Version
-----------------------------------------------------------------
1 OK 77C/71C ver-mismatch 03.00.41
2 OK 73C/73C ver-mismatch 03.00.41
I have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
View 3 Replies View Related