Cisco WAN :: 7204 VXR - Valid Image On Boot Flash
Oct 24, 2012
I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
View 1 Replies
ADVERTISEMENT
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Dec 22, 2012
I purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
View 0 Replies
View Related
Jun 23, 2011
I have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 Replies
View Related
Sep 15, 2012
I have a cisco 2821 Router , it was operating fine but for the past 2 days its having a weird problem.During operation suddenly the connection is lost and when checked through console there is no IOS image on the Router (all configuration is erased and the router boots up in rommon mode and there is no IOS on dir Flash:I installed ios on it through tftp but again after some random time the IOS is automatically erased from flash i checked the config register value and its fine at 0x2102.
View 5 Replies
View Related
Jun 19, 2012
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies
View Related
Oct 3, 2012
I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies
View Related
Nov 1, 2011
I have an ASA 5520, currently running version 7.25-k8. I'm preparing for an upgrade to version 7.25(4), so I transferred the software code (obtained via Cisco download) to the firewall vis SCP. I then issued the "verify flash:asa725-k8.bin" and it fails. It comes back with the error that the CRC did not verify, Data Integrity has been compromised". My first thought was the image did not copy correctly, so I deleted it and transferred it again. I got the same error. Then I decided to run a verify against the actual current code that was running on the firewall, and it came back with the same error. I don't understand what the problem is. I don't tend to think it's an SSH key related problem, as the method I use to access the firewall is via SSH and I have no problems. Worth noting,this firewall is part of an active/standby pair, and I observe the same behavior on the failover unit, it fails to verify.
View 3 Replies
View Related
Dec 30, 2011
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
View 6 Replies
View Related
Apr 29, 2012
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies
View Related
Nov 27, 2011
I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
View 1 Replies
View Related
Feb 26, 2012
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
View 6 Replies
View Related
Dec 29, 2011
I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
View 3 Replies
View Related
May 1, 2011
I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
View 1 Replies
View Related
Jan 20, 2013
I have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
View 4 Replies
View Related
Jan 6, 2013
I've had occasional issues with 5505 upgrades going south when the boot hangs on the image load due to a corrupt image. I need a way to validate the checksum of the new image after it is copied to flash. Remote upgrades become a real pain when you have to go onside just to delete an image, copy it into flash again, and boot.
View 1 Replies
View Related
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
Nov 1, 2011
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
View 7 Replies
View Related
May 27, 2013
i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
View 1 Replies
View Related
May 13, 2013
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies
View Related
May 18, 2013
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
View 7 Replies
View Related
Jan 25, 2013
How do I add network drivers to a wds boot image on 2003R2. I see that 2008 has the add driver option but that doesn't exist in 2003r2.
View 1 Replies
View Related
May 2, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Jan 22, 2008
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
Feb 28, 2011
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
View 1 Replies
View Related
May 9, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop :I know that the solution would be to download a new valid image from tftp via the rommon prompt but what i dont undertand is why i cant access the rommon prompt. It justs boots with the message above in a loop
View 0 Replies
View Related
Sep 22, 2012
I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
View 1 Replies
View Related
Sep 29, 2012
I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
View 1 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
May 23, 2011
I have a cisco 7204 vxr that terminates a 300 meg ethernet circuit asn well as an mpls DS-3. CPU increases along with utilization of the ethernet circuit. When the utilization gets to around 150 Mbps on the receive, the cpu is maxed out at 100%. I am wondering if the router can support the amount of traffic coming through it. The majority of the traffic is voip using g729 codec, so packet size is small. We are no where close to peak utilization and cpu is at 39%. Here is what I see currently:
#sh verCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(15)T4, RELEASE SOFTWARE (fc2)Technical Support: [URL] 1986-2008 by Cisco Systems, Inc.Compiled Thu 13-Mar-08 10:40 by prod_rel_team
ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.3(15), RELEASE SOFTWARE (fc3)
uptime is 3 years, 1 week, 3 days, 6 hours, 40 minutesSystem returned to ROM by Reload CommandSystem restarted at 08:26:49 UTC Wed May 14 2008System image file is "disk2:c7200-advipservicesk9-mz.124-15.T4.bin"
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
[code].....
View 5 Replies
View Related