We have two SSID's Guest and Corp. We are using 5508 controllers.
The problem is that if an iPad user is connected to Guest SSID and then try to connect to Corp then it fails saying "Unable to connect to Corp". After 10-15 retires the same iPad connects successfully. The problem doesn't happen on windows PC. I have attached debug for one of the clients.
We have a remote location with 1 LWAPP AP connecting to a 5508 WLC. We are doing 802.1x auth/wpa2 on 1 SSID for iPads to connect to. Now we want to simply connect a printer to print wireless using AirPrint from the iPads. The problem is how to get the printer connected to the wireless network specifically to the sane SSID? Will the printer need to support 802.1x or have the ability to do certificates? Is there a better way to do this.
View 5 Replies View RelatedI have had an Ipad for 2 months that has until today connected with my network fine. Now I can't get a connection but my laptop will connect fine.
View 2 Replies View RelatedHave WLC 5508 running 7.4 code; have wlan setup to allow access to internal network. Users on ipads should be able to connect to this wlan and authenticated via certificate instead of PSK. We have setup laptops that are part of domain to use internal CA for authentication to WLAN. Ipads are not part of domain so we are not able to use the same model, or can we use the same model for authentication?How to setup WLC to authenticate ipad users via certificate instead of PSK while connecting to the WLAN?
View 1 Replies View RelatedWe are implementing a new corporate wireless network with Cisco 5508 WLC's and C3602I LWAP's. We are not running any RADIUS or EAP at the moment and are starting with WPA2 w/ AES with a pre-shared key to begin piloting. The issue we are having is iOS based devices (iPhone/iPad) do not seem to want to connect. We just get a could not join wireless network messages. We have had success with several Windows based laptops, my MacBook connects, as well as several different Android devices.Looking at the logs on the WLC I see these entries which correspond to the MAC address of my iPhone.
*apfMsConnTask_6: Jul 17 17:25:20.620: %APF-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 Could not check supported rates. Missing Supported Rate. Length :0. Mobile MAC: 24:ab:81:92:4d:97.
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies View RelatedGuestconnect SSID configured on 5508 WLC with Pass through athentication (NAC guest server). No issue with Laptops and Iphone/Ipad ver 4and 5. Only Iphone Ver 6 users unable to access Guest connect .
View 9 Replies View Relatedrecently we have purchased Reflection - an AirPlay mirroring software. Basically install Reflection in the laptop and you can view the screen of the iPad or iPhone via wireless network. we have tested in home wireless network no problem, but when connect to the cisco network, the iPad didn't recognize the REFLECTION installed in the laptop.
we are running WLC 5508, WLAP AP-1331AG, we can ping from laptop to the iPad laptop and ipad can access network without any issue. there is no any application port has been blocked between the client via wifi extra details for REFLECTION: [URL]
I have a 5508 WLC and 40+ LAP1142N APs spread across 19 locations that allows staff to connect to our private network via wireless. I recently deployed about 40 new laptops all identical make and model HP ProBook 4530's and all have the same client setup for the wireless. Out of those 40 laptops I have 4 that will not connect to the private network. However, these same laptops will connect to my public, open wireless network without issue. In addition to the 4 that will not connect all the others will prompt twice for network authentication.Now, I have about 10 other laptops that are not the HP model and all connect without issue and without dual propt. I don't think this is a wireless network issue but could be some type of issue with this model of laptop.
View 8 Replies View RelatedWe have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
We find that some of the utilized iPads (iPad2, iOS 5) have a significant delay to connect to the WiFi after waking up.. though some of them show the WiFi-icon instantly after wake-up.. That is causing the crestron App on it to "malfunction", which is to say that it can't connect to it's server and goes back to home screen to allow re-connect..
WLC and LAPs using the latest software (7.2.103.0).. encryption is WPA2/PSK..
I changed the WLAN to use 802.11g only.. changed Beacon-Time.. changed encyption.. changed WMM settings..Alas, the iPads that expose this behaviour do not show any difference with the changes..
I have 1 WLC AIR-CT5008-K9 version 7.0.98.0. with iPads connected to a WLAN with [(WPA+WPA2)(AuthPSK)].and have constant disconnections. But the Laptops do not have problems.
View 5 Replies View RelatedUsing wireless PEAP via a 5508 controller and a verisign cert on ACS 4.1,The iPad still wants me to verify the cert even though it is a trusted CA.
View 2 Replies View RelatedI recently had a 5508 controller installed and configured for a corporate network as well as internet only guest access. Users authenticate via 802.1X key management on the corporate network and web authentication via guest. This works fine, however, I've run into a problem. We also use iPads for inspections and the inspection site is housed internally. I've had a network admin create an exception in the firewall that will allow connection to the internal sites from the guest network, however, it does not function. I did find that if I connect an iPad to the corporate wireless network I'm able to download the necessary certificate to the device but that only works if I use my login information which is not something I am interested in doing. Is it possible to enable another authentication for the corporate network without breaking the functionality of the existing 802.1X authentication? What could possibly be the cause on the guest network not allowing connectivity to the internal sites, even though the exception has been created?
View 3 Replies View RelatedI am able to access the servers in the network when i am on the LAN . The problem is while we are connected to the VPN, I am unable to https to the servers. While on the VPN, I can ping and traceroute to the servers but I cannot HTTPS.We are using the 3000 series concentrators and also ASA's.This thing was working fine until recently we did a network migration from 6500's to Nexus.
View 1 Replies View RelatedI have an existing home network with several win7 and XP machines connected.I would like to connect a new iPad wireless to th same work group. The iPad connects fine to the network and can access the internet.However, the iPad doesn't seem to see the other computers in the work group I want to connect it to, nor do the windows computers see the iPad. This is surely due (at least in part) to not having specified the work group name on the iPad, which I cannot figure out how to do.
View 6 Replies View RelatedHow do I connect IPAD to Linksys router WRT160n?
View 2 Replies View RelatedWe have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies View RelatedI have a WRT320N router with firmware version 1.0.01 build 008. I just got an iPad and while it can find my router, I can't access the WiFi when I enter my password. I can use the router with my laptop so I know the connection and password are ok.I've seen two administrators on here suggest the same thing. And one person responded that it worked. The identical directions were:
Try changing some advanced wireless settings on the router.Connect the computer to the router with the Ethernet cable. Open the setup page of the router.Click on wireless tab and set the configuration view to manual. Change the wireless channel to 11. Save the settings.Go to wireless tab and click on Advanced wireless settings.Change Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.Try to connect to the wireless network again and see if that works.
1 - I think my computer already is connected to the router with the Ethernet cable - I mean there is an Ethernet cable attached to both my computer and my router - in slot 1 on the router
2 - the only thing I know how to access is the Linksys EasyLink Advisor. What and where is the setup page of the router?
What should i do ? Reset ? How ? maybee i did not set the cable properly ( what is an ethernet cable ? ) the one i have is a short cable with what looks like telephone jacks at either ends. one end is plugged in my comcast modem and the other into my mini mac.
View 1 Replies View RelatedI really worked hard not to write this question here but here I am. I am trying to route all traffic through vpn but I cant browse the web. It seems no traffic goes through the vpn tunnel. Split tunneling works but it doesnt route the traffic through vpn tunnel. I have a cisco asa5505 with base license,
When I try to browse the web with one of the clients I see lots of
6Apr 07 201309:40:5510.10.50.136088410.10.10.153Built inbound UDP connection 834 for outside:10.10.50.13/60884 (10.10.50.13/60884) to outside:10.10.10.1/53 (10.10.10.1/53) (xxxx
messages but at the end I see " Safari could not open the page because the server stopped responding" message or smth similar.
My setup is
Vpn Clients ====== asa5505 ========== CiscoLinksysEA4500 Router ======== ISPProvidedFiberConverterDevice(huawei)
10.10.30.10-10.10.30.50 10.10.10.2(outside int) 10.10.10.1(inside) PPOE(outside)
[Code].....
I have tried to make a VPN connection between RV180W and iPad with PPTP. I have enabled the server, set the address range, added and user and enabled it.
I entered the same information into iPad but when I try to start the VPN, iPad just tried to make connection and finally fails with an error stating that PPP server cannot be reached.
I think the devices are able to make some kind of connection as if I change the gateway IP address incorrect, I get a different kind of error message. I also tried to reboot the router...
I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
View 1 Replies View Relatedi got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies View RelatedI recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies View RelatedI cannot get my belkin n150 wireless router to connect to my laptop or ipad - wireless connection was working but stopped - so i attempted to re-configure the ip protocols on the router using the 198.168.2.1/ password - changed the ip setting on the belkin page but did not reset or set address (DHCP).
View 1 Replies View RelatedI don't want to allow any Guest access to my network, but I do want to connect my iPad to my network. I've successfully added another computer to the network but the router setup seems to want the iPad to connect only as a Guest .Is there a way to treat my iPad as another computer (not as Guest) so that it my network recognizes it in the same way it recognizes the second computer (without entering a password)?
View 1 Replies View RelatedMy iPad cannot connect to my network wireless through WPA2 using router E4200 the way my Macbook is connected. Only using guest access i can get internet contact. Is this a known problem with this combination and/or is it meant to be, that only guest access gives an iPad connection?
View 6 Replies View RelatedRegion : Canada
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 120608
ISP : Distributel
I've just installed this router today, connected physically 2 PCs, a PS3 and a VoIP and everything works fine !
The problem is with the WIFI connection ! my devices see the WIFI network, they connect, but I cannot connect to the internet ...
What settings Should I turn on/off or any config I should tweak ?
I recently add a second CT5508 to the network, but when I tried to add the first 5508 to the mobilty group I received a message like this:
"error in creating member"
I've tried different mobility names, via GUI, via CLI and always the same error.
I've verified twice or more than twice connectivity issues or any error on the entering the MAC and IP of the controllers, everything is fine.
I'm using version 7.0.116.0
I have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
I had configured a Cisco 5508 series WLC. The APs used are Cisco 3502 LAP. The APs are configured to use DHCP for this ip addresses.
We had configured the DHCP server on the 2 Windows AD server previously and the APs were not able to get an IP address when the WLC was rebooted. To isolate the cause, we configured the DHCP server on a cisco 6500 switch. When we reboot the WLC, most of the APs are not able to grab an IP address. We had to remove and reconfigure the DHCP pool on the cisco 6500 for the APs to capture the IP addresses.
My colleague had feedback that they gotten a message that the DHCP pool had been used up. We tried to do a "show ip DHCP pool" but the switch did not recognise the command. IOS version used is Version 12.2(50r)SYS2.
We had a problem with the wireless client getting ip addresses from the windows DHCP server previously but problem was resolved after we disabled the DHCP proxy on the WLC.
What we are curious is why was the DHCP pool fully used on the Cisco switch and how could we check the number of addresses used other than running "show ip dhcp binding" and doing a count of the IP addresses?
Also why did we have to disable the DHCP proxy on the cisco WLC for the wireless clients to be able to get an IP address from the windows DHCP server?
We seem to be facing a number of problems with the DHCP functions for the wireless setup.
