Cisco Wireless :: WLC 5508 - Connect IPad And Printer 802.1x
Dec 1, 2012
We have a remote location with 1 LWAPP AP connecting to a 5508 WLC. We are doing 802.1x auth/wpa2 on 1 SSID for iPads to connect to. Now we want to simply connect a printer to print wireless using AirPrint from the iPads. The problem is how to get the printer connected to the wireless network specifically to the sane SSID? Will the printer need to support 802.1x or have the ability to do certificates? Is there a better way to do this.
View 5 Replies
ADVERTISEMENT
Sep 4, 2011
We have two SSID's Guest and Corp. We are using 5508 controllers.
The problem is that if an iPad user is connected to Guest SSID and then try to connect to Corp then it fails saying "Unable to connect to Corp". After 10-15 retires the same iPad connects successfully. The problem doesn't happen on windows PC. I have attached debug for one of the clients.
View 1 Replies
View Related
Jan 5, 2013
Have WLC 5508 running 7.4 code; have wlan setup to allow access to internal network. Users on ipads should be able to connect to this wlan and authenticated via certificate instead of PSK. We have setup laptops that are part of domain to use internal CA for authentication to WLAN. Ipads are not part of domain so we are not able to use the same model, or can we use the same model for authentication?How to setup WLC to authenticate ipad users via certificate instead of PSK while connecting to the WLAN?
View 1 Replies
View Related
Jul 16, 2012
We are implementing a new corporate wireless network with Cisco 5508 WLC's and C3602I LWAP's. We are not running any RADIUS or EAP at the moment and are starting with WPA2 w/ AES with a pre-shared key to begin piloting. The issue we are having is iOS based devices (iPhone/iPad) do not seem to want to connect. We just get a could not join wireless network messages. We have had success with several Windows based laptops, my MacBook connects, as well as several different Android devices.Looking at the logs on the WLC I see these entries which correspond to the MAC address of my iPhone.
*apfMsConnTask_6: Jul 17 17:25:20.620: %APF-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 Could not check supported rates. Missing Supported Rate. Length :0. Mobile MAC: 24:ab:81:92:4d:97.
View 28 Replies
View Related
Jul 27, 2012
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies
View Related
Nov 18, 2012
recently we have purchased Reflection - an AirPlay mirroring software. Basically install Reflection in the laptop and you can view the screen of the iPad or iPhone via wireless network. we have tested in home wireless network no problem, but when connect to the cisco network, the iPad didn't recognize the REFLECTION installed in the laptop.
we are running WLC 5508, WLAP AP-1331AG, we can ping from laptop to the iPad laptop and ipad can access network without any issue. there is no any application port has been blocked between the client via wifi extra details for REFLECTION: [URL]
View 4 Replies
View Related
Mar 5, 2013
We have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
View 9 Replies
View Related
Apr 11, 2012
We find that some of the utilized iPads (iPad2, iOS 5) have a significant delay to connect to the WiFi after waking up.. though some of them show the WiFi-icon instantly after wake-up.. That is causing the crestron App on it to "malfunction", which is to say that it can't connect to it's server and goes back to home screen to allow re-connect..
WLC and LAPs using the latest software (7.2.103.0).. encryption is WPA2/PSK..
I changed the WLAN to use 802.11g only.. changed Beacon-Time.. changed encyption.. changed WMM settings..Alas, the iPads that expose this behaviour do not show any difference with the changes..
View 3 Replies
View Related
Aug 8, 2011
I have 1 WLC AIR-CT5008-K9 version 7.0.98.0. with iPads connected to a WLAN with [(WPA+WPA2)(AuthPSK)].and have constant disconnections. But the Laptops do not have problems.
View 5 Replies
View Related
Feb 28, 2011
Using wireless PEAP via a 5508 controller and a verisign cert on ACS 4.1,The iPad still wants me to verify the cert even though it is a trusted CA.
View 2 Replies
View Related
Mar 26, 2013
I recently had a 5508 controller installed and configured for a corporate network as well as internet only guest access. Users authenticate via 802.1X key management on the corporate network and web authentication via guest. This works fine, however, I've run into a problem. We also use iPads for inspections and the inspection site is housed internally. I've had a network admin create an exception in the firewall that will allow connection to the internal sites from the guest network, however, it does not function. I did find that if I connect an iPad to the corporate wireless network I'm able to download the necessary certificate to the device but that only works if I use my login information which is not something I am interested in doing. Is it possible to enable another authentication for the corporate network without breaking the functionality of the existing 802.1X authentication? What could possibly be the cause on the guest network not allowing connectivity to the internal sites, even though the exception has been created?
View 3 Replies
View Related
Aug 7, 2011
Trying to print from an IPAD to a KODAK ESP9 printer via the WAG 120N?
View 1 Replies
View Related
Oct 3, 2012
I have had an Ipad for 2 months that has until today connected with my network fine. Now I can't get a connection but my laptop will connect fine.
View 2 Replies
View Related
Jun 25, 2012
I have an existing home network with several win7 and XP machines connected.I would like to connect a new iPad wireless to th same work group. The iPad connects fine to the network and can access the internet.However, the iPad doesn't seem to see the other computers in the work group I want to connect it to, nor do the windows computers see the iPad. This is surely due (at least in part) to not having specified the work group name on the iPad, which I cannot figure out how to do.
View 6 Replies
View Related
Feb 23, 2012
How do I connect IPAD to Linksys router WRT160n?
View 2 Replies
View Related
Apr 21, 2012
We have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies
View Related
Jul 24, 2011
I have a WRT320N router with firmware version 1.0.01 build 008. I just got an iPad and while it can find my router, I can't access the WiFi when I enter my password. I can use the router with my laptop so I know the connection and password are ok.I've seen two administrators on here suggest the same thing. And one person responded that it worked. The identical directions were:
Try changing some advanced wireless settings on the router.Connect the computer to the router with the Ethernet cable. Open the setup page of the router.Click on wireless tab and set the configuration view to manual. Change the wireless channel to 11. Save the settings.Go to wireless tab and click on Advanced wireless settings.Change Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.Try to connect to the wireless network again and see if that works.
1 - I think my computer already is connected to the router with the Ethernet cable - I mean there is an Ethernet cable attached to both my computer and my router - in slot 1 on the router
2 - the only thing I know how to access is the Linksys EasyLink Advisor. What and where is the setup page of the router?
View 4 Replies
View Related
May 14, 2013
What should i do ? Reset ? How ? maybee i did not set the cable properly ( what is an ethernet cable ? ) the one i have is a short cable with what looks like telephone jacks at either ends. one end is plugged in my comcast modem and the other into my mini mac.
View 1 Replies
View Related
Aug 27, 2011
I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
View 1 Replies
View Related
Mar 22, 2012
i got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies
View Related
Jun 26, 2012
I recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies
View Related
Jun 3, 2013
I cannot get my belkin n150 wireless router to connect to my laptop or ipad - wireless connection was working but stopped - so i attempted to re-configure the ip protocols on the router using the 198.168.2.1/ password - changed the ip setting on the belkin page but did not reset or set address (DHCP).
View 1 Replies
View Related
Mar 26, 2012
I don't want to allow any Guest access to my network, but I do want to connect my iPad to my network. I've successfully added another computer to the network but the router setup seems to want the iPad to connect only as a Guest .Is there a way to treat my iPad as another computer (not as Guest) so that it my network recognizes it in the same way it recognizes the second computer (without entering a password)?
View 1 Replies
View Related
Nov 18, 2011
My iPad cannot connect to my network wireless through WPA2 using router E4200 the way my Macbook is connected. Only using guest access i can get internet contact. Is this a known problem with this combination and/or is it meant to be, that only guest access gives an iPad connection?
View 6 Replies
View Related
Apr 6, 2013
Region : Canada
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 120608
ISP : Distributel
I've just installed this router today, connected physically 2 PCs, a PS3 and a VoIP and everything works fine !
The problem is with the WIFI connection ! my devices see the WIFI network, they connect, but I cannot connect to the internet ...
What settings Should I turn on/off or any config I should tweak ?
View 4 Replies
View Related
Jul 9, 2012
Is it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
View 5 Replies
View Related
Jun 13, 2012
My kids have IPads and wish to connect to the media on my win7 system ??
View 1 Replies
View Related
Apr 10, 2012
I have a PC with the following OS and Routers
PC: Win 7 x86
iTunes: 10.6
Router: DIR-655 (Firmware Version: B1, 2.06)
My new iPad cannot connect to iTunes for either home sharing or Wi-Fi Sync.I have check the windows event log and provides the following error lists....
444: ERROR: read_msg errno 0 (The operation completed successfully.)ERROR: mDNSPlatformReadTCP - recv: 10053..The following ports have been set up in Router Port Forwarding/Virtual Servers
-TCP: 3689
-UDP: 5353
I have disabled DMZ and enabled Multi Stream Cast, but it seems no use on the problem solving.The same errors are still provided. iPad cannot in the device list if it is in Wi-Fi connection, no home sharing.As I am not in US, the local supplier latest firmware version is 2.06NA Beta1
View 3 Replies
View Related
Jan 27, 2013
Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..Get these errors when i run the debug crypto isakmp.
View 6 Replies
View Related
Jan 8, 2012
The web authentication page comes up but as soon as the user hits Submit, the following error appears:
Error Opening Page Hot Spot login cannot open the page because the network connection was lost.
I've tried all the suggestions on these forums but none have worked: [URL]
I'm using a Services Ready Engine Service Module in a 2921 router as my WLC. The same i Phones/i Pads can connect fine using MAC filtering and WPA2.
View 10 Replies
View Related
Sep 14, 2011
I have a Home network via a Prestige P660 NW - T1 router which has worked fine but I recently bought an IPad 2 with Wifi but I can't connect to my Network with my Password - When I remove the Password and change the router settings to no authentication I can connect but I don't want to have no security on the router.Relatives have tried with their IPads and even though we all carefully put in the Password we cannot access the Network.
View 5 Replies
View Related
Feb 6, 2013
My pc was working fine till I shut it down n restarted it and now it won't connect to the Internet I am running windows vista 32 bit service pack 1 and is wired to my router but I can connect my ipad(which I'm using now) and iPhone through wireless
View 12 Replies
View Related
Jun 21, 2011
I have an iPad2 and a Belkin F6d4230-4 wireless router. I no longer have a computer. If I reset the router can I setup the network without having to hard-wire the router to a computer first?
View 3 Replies
View Related
