Cisco Switching/Routing :: RVO82 Web Pages Not Fully Loaded
Aug 14, 2011
I'm using a RV082 and have about a dozen users on my network.Occasionally, when a user is accesssing a website like yahoo.com, twitter.com, cnn .com, etc, the web page only loads half way. Most often the page is missing stylesheets and/or images. Called Cisco support and they adjusted the MTU size to 1492 from 1500.Have a looked at the bandwidth report from my ISP and it shows nothing out of the ordinary, no spikes or surges in d/u. Have set LAN port to high priority, 100 Mbps, full duplex.. Seeing an error count around 327282.. which I don't understand.Why sites only partially load using this router?
View 1 Replies
ADVERTISEMENT
Nov 27, 2011
My computer (running windows XP and connected to the internet with a D Link USB adapter) refuses to load any webpages: despite showing full signal strength and connection in both the D Link settings and the windows XP wireless panel.I am able to ping websites and other computers in the house (all of which are able to access the internet) but no pages load in any browser I try.
View 1 Replies
View Related
Jan 11, 2012
2950 switch has a IOS on flash , but i would like to set the swith like...
1. switch IOS to be loaded from TFTP server .if it fails
2. Loaded from local flash IOS1 , if it fails
3. IOS loaded from local flash IOS2.
does 2950 switch support this feature.
View 2 Replies
View Related
Jul 23, 2012
Can a C3560-24PS switch with 32 MB flash be loaded with IOS 15? Will it be able to execute the code and function properly?
View 2 Replies
View Related
Oct 13, 2012
Recently I changed our default gateway from a pair of PIX515 to ASA5510. Since I changed the gateway anyone connecting to our wireless VLAN/network who tries to access the Internet may or may not get a page load. If the page loads it is extremely slow and sometimes the browser page indicator will just spin like it is loading. It's not our access points, if attach an ethernet cable to my laptop and put my switchport in the wireless VLAN I experience the same problem. DNS resolves OK, ping responses are consistent with no drops and access to any internal resources are good. All other LAN VLANs/networks work just fine, it's just Internet access on the wireless VLAN. I see the correct traffic flow in the ASA packet capture. Anything in the ASA Packet inspection related to wireless networking that could be blocked? Is there a way to check for a routing loop possibly?
View 2 Replies
View Related
Jun 2, 2013
let me know the exact meaning of attach ( yellow marked one)? the contractor was saying "it doesn't mean two switches as there is a built in redundancy in Cisco switch)"I don't think he is correct as I never heard about built in redundancy in Cisco Router/switchAny comment as this will affect the numbers from 55 (3750 v2) to 110....
View 41 Replies
View Related
Nov 11, 2012
We have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
View 2 Replies
View Related
May 13, 2012
Background information, have had the 4150L for probably about a year and haven't had a bit of trouble with it. I just updated the firmware this morning and it still seems to be working great. This is the first upgrade I have ever done to it. Anyway, what I am trying to accomplish, I have discovered that I can remotely connect to my office computer through my iPad using itap RDP and a VPN connection. I have already been able to use itap RDP in the office to show patients their x-rays etc... on the iPad. I have a cisco RVO82 router and my office software suggests the use of a PPTP VPN to connect remotely. I have checked all the settings and I have everything set as described. The iPad shows a VPN connection icon but when I try to connect to my computer, I get a TCP error. From what I have read, some people are able to connect via VPN on the 4150L and others are not.
View 1 Replies
View Related
Feb 12, 2011
I'm havoing probems with my network "stuttering" and wanted to update the firmware. The RVO82 is currently running v2.0.0.19-tm and I have downloaded the latest; V 4.0.0.0.07-tm and tried to upload it to the router using both Safari and Firefox but the update won't take. I have followed the instructions to go to a fixed ip of 192..168.1.50 and have a connection directly to the router( bypassing the switch) but cannot get it to update.
View 1 Replies
View Related
Oct 26, 2011
url is not valid and cannot be loaded
View 1 Replies
View Related
Feb 28, 2012
ASDM cannot be loaded. Click OK to exit ASDM. Server returned HTTP response code: 503 for URL...
I'm attempting to access the ASDM externally (where x.x.x.x is the external IP). I was able to access 3 days ago just fine. So far, I've found suggest a reboot.
ASA Version 8.2(1) - I think the ASDM version is 6.2
View 11 Replies
View Related
May 6, 2012
I have a small network, that consists of a wireless router, a switch, three wired pc's, a couple of wireless pc's and an xbox.I have a switch wired to the router. There are three pc's (2 with XP and 1 with vista) and a xbox connected to the switch. All three pc's work fine as long as the xbox is turned off. When I log on with the xbox, one of the pc's (vista) refuses to work on the network.The network and sharing center shows I have a connection to the internet, but it won't load any pages or allow me to connect to the other pc's either.
View 6 Replies
View Related
Apr 25, 2013
Is it possible to have a license loaded on an AIR-CT5508-HA-K9 in order to have it working as a stand alone controller?
View 4 Replies
View Related
Sep 24, 2012
I have a cisco 5508 WLC that I have setup WebAuth on and trying to install the certificate on. I have generated the csr and gotten my cert from Verisign (X.509, server platform=apache). I have followed the instruction via the cisco documentation url...I found an error in uploading and find out how to encrypt mykey: url...
I am also having exactly the same issue with a certificate from Thawte. I followed the unchained guide and have tried both with and without a password in the initial step key generation step, requesting a new cert each time. As with Jeensernchew's issue there are no errors in OpenSSL but when uploading the cert to the WLC get the following error. [code] The WLC is running version 6.0.196.0. I am using OpenSSL 1.0.0 29 Mar 2010.
When I requested the cert from Thawte I was asked to specify the device type, I chose Cisco, but as all the work and conversion is being done by OpenSSL, should I have chosen differently? When I do this I can load the cert in the 5508, but the controller fails and doesn't allow that VLAN or config access to the wireless network. I am at a loss of why I can load and it not work. I have verified my hostname and password and those are good.
View 1 Replies
View Related
Mar 24, 2012
I already have large deployment add-on license. I also have 3 ACS Servers. Now, my primary ACS server is now up and my two secondary ACS server will be put up soon.
Just want to ask, when should be the large deployment add-on license be loaded? Can I load it to my primary ACS server eventhough my secondary servers are still not up? Or should I load it to my primary ACS server when my two secondary servers are already up?
View 3 Replies
View Related
Aug 23, 2012
The host computer runs Windows XP (SP3), and the client - Windows 7 Ultimate. The host computer connects to the internet with a USB wireless modem (HSUPA USB modem by ZTE). So I enabled sharing and connected the two computers with an Ethernet cable, so the first time it worked. The next time I turned on the computers I wasn't able to share the internet, I wasn't able to load any pages on the client computer, however Skype was working. I tried to use various guides on how to input IP addresses manually etc, but that didn't work, finally I felt like I had changed so much that I decided to restore both machines to an earlier point and start over, that still didn't work.
Then I bought a Cross-over Ethernet cable, and the first time I connected the computers - the internet was working on the client computer, I reboot - only Skype works.When I try to diagnose the problem on Windows 7, it usually can't find anything (it says that I have access to the Internet, but in the "Details..." it says that IPV6 has no internet access), or once it said something about IP addresses but wasn't able to fix it, the other time it said that DHCP wasn't enabled on the client computer and it enabled it and the internet started working. Right now on the client computer in LAN "Details..." it says that DHCP is disabled, but the diagnostic tool doesn't detect anything.
What numbers I should blur, when I restored, on the XP (host) computer the antivirus broke down (avast, free), so I had to uninstall it with a special uninstaller through safe mode and install it again, so when I reinstalled the internet sharing was working again, so it made me think that it was avast's fault, however there's no firewall in my free version so in avast forum I was told that avast is not the problem.
View 5 Replies
View Related
Jan 6, 2012
I am having a tough time connecting these two routers wirelessly, i had connected a WRT54G Linksys software to the WRT54G DD-WRT router with no effort. But these two will just not connect.
View 1 Replies
View Related
Apr 7, 2013
My daughter bought a Dell Optiplex 745c from a company who is replacing their cmputers. This particdular computer does not have any drivers loaded for the installed NIC card, so te machine will not talk to the intenet. Are the drivers in the 745 and the 755 the same?
View 1 Replies
View Related
Jul 25, 2011
i just bought a 5508 wireless controller that was delivered yesterday .I powered it on yesterday and was able to make basic configurations of management interface ,time and zone settings.I was also able to get to the GUi and console after the configs and it was alright. When I got in this morning it ran for about 2 hours and all of a sudden starts shutting down after every % minutes and comes back again.
View 7 Replies
View Related
Apr 29, 2013
I have a WCS v.7.0.230.0 and four controllers v.7.0.235.3 (on two WiSMs). I have a problem now where when adding/modifying guest users the controller list shows only three controllers. I don't know when this started happening or why but no matter what I do (including removing the controller and adding it again) I can't get the controller list to be fully populated with all four controllers. I've attached an image of what I'm seeing.Other functionality appears to be normal, for example I can add "mac filtering" addresses to all four controllers with no problem, APs can register to the affected WLC etc.
View 2 Replies
View Related
Jan 21, 2012
i have tried many things i have tried to reset my router with the cmd prompt i have checked my drivers i have tried the simple things and at this point.
View 1 Replies
View Related
Jun 24, 2012
I am trying to configure two inside interfaces without NAT. I am not using nat-control and I have added exemptions for the two networks. I can communicate between the two networks and to the Internet just fine.I would like to verify that NAT is disabled between the two interfaces. I also need to make sure that the Interface IP (specifically for the traffic from inside-test to the inside network) is not added to packets between the two networks. I would like to be able to verify this as well. In other words I need to have the Source IP address from the originating connection on the inside-test network passed along through to the Inside network device without being replaced by the Interface's IP address. This is a test config for a production environment that will be using a load balancer. The config I have may be working in this regard and the load balancer may be replacing this IP address (that is what I am trying to test), but I am not certain.So far I have the following NAT related running-config command (in regards to these two interfaces):
access-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0access-list NAT_Exempt_2 extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list NAT_Exempt_2nat (inside) 1 0.0.0.0 0.0.0.0nat (Inside-test) 0 access-list NAT_Exemptnat (Inside-test) 1 0.0.0.0 0.0.0.0
global (outside) 1 interfaceglobal (Inside-test) 1 interface
View 11 Replies
View Related
Apr 8, 2013
We've put in a 3750 at our corp hq (Detroit). We did this to break up the current flat 172.16.0.0 /16 network into separate VLAN's for various purposes. We plan on doing that at another site (Farmington), which will become a DR site. We are running EIGRP throughout the organization over an OPTEMAN netowrk and also sending routes to a managed MPLS network which uses BGP. BGP redistributes into EIGRP and vice versa. I've attached a pdf of the network. The 3750 core at the corp hq is a temp core, hopefully upgrading to Nexus within a year or two. This problem didn't exist until the 3750 was introduced and became the gateway for the site. The OPTEMAN router was the gateway and was on the same VLAN as the MPLS router.
So, in detroit we have an Detroit-MPLS router, Detroit-3750, and Detroit-OPTEMAN. What I'm seeing is that the routers I'm getting from the MPLS router make it to the 3750. The 3750 advertises those routes to the Detroit-OPTEMAN router. However, the OPTEMAN router doesn't advertise these routes any further..
In Farmington, it is currently set up like Detroit used to be set up. There is a flat network and both routers are on the same VLAN, no L3 core switch. Routes come in from the MPLS, get advertised to the Farmington-OPTEMAN router, distributes the routes out to all OPTEMAN connected routers, including Detroit. However, Detroit is not passing that route to the 3750.
When we made the 3750 stack the core, we didn't change anything else, except for some IP changes. Why these routes aren't fully redistributing?
Detroit-3750 Stack
WS-C3750G-24TS-S <-Stack master running c3750-ipservicesk9-mz.122-55.SE7.bin
WS-C3750X-12S-E <-Running c3750e-universalk9-mz.122-55.SE7
show sdm prefer
The current template is "desktop routing" template.
[Code]...
View 6 Replies
View Related
Dec 15, 2011
I have a Linksys WRT54GL router in one building and a second router in an adjacent building. I have connected each router to a MODEM that takes me to the internet. Can I configure the two routers to talk to each other and at the same time maintaining their respective internet connections
View 4 Replies
View Related
Jun 21, 2011
What is supported in terms of running a mixed feature set in a Cisco 3750 switch stack.We are looking at setting up a stack consisting of 5 x 3750V2 and 2 x 3750G. Due to a requirement for full EIGRP we need the IP Services feature set. Is it a supported configuration to run with 2 or 3 switches running the IP Services feature set as stack masters and the others running IP Base? I understand that if stack master priorities were set these switches with the higher feature set could manage the stack and offer IP Services accross the stack. If we were to lose all of the switches running IP Services the stack would drop back to IP Base.I am looking for guidance as to if this is a supported configuration and not in breach of licensing? Is this likely to cause any problem other than above now and for future IOS releases?
View 2 Replies
View Related
Mar 24, 2013
It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it
View 9 Replies
View Related
Mar 13, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
View 2 Replies
View Related
Feb 17, 2010
Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...? Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.
View 3 Replies
View Related
Mar 18, 2013
I have a Linksys Wireless G PCI adapter. The model is WMP54gs and the serial number MGP00E416793. I am trying to install this adapter on a Windows XP media center computer. The computer is update to date with all windows updates. I need the driver and software to successfully get this adapter to fully work.
View 3 Replies
View Related
Jan 9, 2012
Set up wireless internet with this computer. After going through set up wizard my computer would not fully connect to wireless. It is connected to the network but the internet does not go through. When diagnosing the problem windows says "A problem with your network router or broadband modem might be preventing an internet connection. My husbands computer and phone have no problem connecting. My computer says the wireless network adapter is working properly and I seem to have no trouble connecting to other wireless connections.
View 4 Replies
View Related
Apr 8, 2013
I am using a Netgear DG834N modem/router that we moved onto our second phoneline (homeline) that was previously installed on our (now closed down) home office phoneline. We are using the same equipment, provider and provider plan but now we are having major connecting issues. About every second web page will not open. If you refresh, sometimes it will load other times you get the "IE cannot connect to.." This is becoming increasingly frustrating. We run both wireless and hardwired PCs and laptops and use IE, firefox and/or Safari. We run Kaspersky or bitdefender, windows 7 and XP. We can watch re-runs of Tv shows and you-tube no worries. It is the connecting in the first place.
View 5 Replies
View Related
Jul 11, 2012
IE9 can't display any webpages. Troubleshooting shows that it can't detect my proxy settings. However, I don't have proxy settings/server checked anywhere. Moreover, Pale Moon is able to connect to the internet.I've tried these so far with no luck:
1. Resetting IE
2. Reinstalling IE
3. Removing idstore to see if it'd work -- nope
4. going to cmd and using dnsflush, ipv4/6 reset, winsock reset, ipconfig release
5. Reinstalling adapter
6. Removing firewalls
7. SFC scanner
Windows IP Configuration
Host Name . . . . . . . . . . . . : GLaDOS
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[Code]...
View 5 Replies
View Related
Apr 20, 2011
The combination of the two line are successful and the internet is working with double speed. I can access all router from my PC but sometimes I have hard time accessing the modem pages. I am not sure the reason but I thing that when I request 192.168.2.1. the request might be sometimes taken to m2 modem , that's why the modem m1 is not found.
View 3 Replies
View Related
