Cisco Wireless :: WCS V.7.0.230.0 - Controller List Not Fully Populated
Apr 29, 2013
I have a WCS v.7.0.230.0 and four controllers v.7.0.235.3 (on two WiSMs). I have a problem now where when adding/modifying guest users the controller list shows only three controllers. I don't know when this started happening or why but no matter what I do (including removing the controller and adding it again) I can't get the controller list to be fully populated with all four controllers. I've attached an image of what I'm seeing.Other functionality appears to be normal, for example I can add "mac filtering" addresses to all four controllers with no problem, APs can register to the affected WLC etc.
View 2 Replies
ADVERTISEMENT
May 9, 2012
I need to know for shure if the aps listed below are compatible with 5508 controller version 7.1.91.0
the ap's are
AIR-LAP1242AG-E-K9
AIR-LAP1242G-E-K9
AIR-CAP3501E-E-K9
AIR-CAP3502E-E-K9
AIR-LAP1231G-E-K9
of course I checked release notes [URL]
View 8 Replies
View Related
Apr 15, 2013
I am using LMS 4.2 I have enabled user tracking and I am getting ip address, MAC address ,hostname in user tracking table . But username entry in user tracking is not getting populated . Even I have enabled get user name from the hosts in NTS and ND host domains in user tracking acquisition settings .Is there anything else that I need to configure in LMS in order to get the usernames in user tracking table?
View 3 Replies
View Related
Jul 25, 2011
i just bought a 5508 wireless controller that was delivered yesterday .I powered it on yesterday and was able to make basic configurations of management interface ,time and zone settings.I was also able to get to the GUi and console after the configs and it was alright. When I got in this morning it ran for about 2 hours and all of a sudden starts shutting down after every % minutes and comes back again.
View 7 Replies
View Related
Dec 15, 2011
I have a Linksys WRT54GL router in one building and a second router in an adjacent building. I have connected each router to a MODEM that takes me to the internet. Can I configure the two routers to talk to each other and at the same time maintaining their respective internet connections
View 4 Replies
View Related
Mar 24, 2013
It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it
View 9 Replies
View Related
Mar 13, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
View 2 Replies
View Related
Mar 18, 2013
I have a Linksys Wireless G PCI adapter. The model is WMP54gs and the serial number MGP00E416793. I am trying to install this adapter on a Windows XP media center computer. The computer is update to date with all windows updates. I need the driver and software to successfully get this adapter to fully work.
View 3 Replies
View Related
Jan 9, 2012
Set up wireless internet with this computer. After going through set up wizard my computer would not fully connect to wireless. It is connected to the network but the internet does not go through. When diagnosing the problem windows says "A problem with your network router or broadband modem might be preventing an internet connection. My husbands computer and phone have no problem connecting. My computer says the wireless network adapter is working properly and I seem to have no trouble connecting to other wireless connections.
View 4 Replies
View Related
Aug 23, 2012
The host computer runs Windows XP (SP3), and the client - Windows 7 Ultimate. The host computer connects to the internet with a USB wireless modem (HSUPA USB modem by ZTE). So I enabled sharing and connected the two computers with an Ethernet cable, so the first time it worked. The next time I turned on the computers I wasn't able to share the internet, I wasn't able to load any pages on the client computer, however Skype was working. I tried to use various guides on how to input IP addresses manually etc, but that didn't work, finally I felt like I had changed so much that I decided to restore both machines to an earlier point and start over, that still didn't work.
Then I bought a Cross-over Ethernet cable, and the first time I connected the computers - the internet was working on the client computer, I reboot - only Skype works.When I try to diagnose the problem on Windows 7, it usually can't find anything (it says that I have access to the Internet, but in the "Details..." it says that IPV6 has no internet access), or once it said something about IP addresses but wasn't able to fix it, the other time it said that DHCP wasn't enabled on the client computer and it enabled it and the internet started working. Right now on the client computer in LAN "Details..." it says that DHCP is disabled, but the diagnostic tool doesn't detect anything.
What numbers I should blur, when I restored, on the XP (host) computer the antivirus broke down (avast, free), so I had to uninstall it with a special uninstaller through safe mode and install it again, so when I reinstalled the internet sharing was working again, so it made me think that it was avast's fault, however there's no firewall in my free version so in avast forum I was told that avast is not the problem.
View 5 Replies
View Related
Aug 12, 2012
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Mar 31, 2013
We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies
View Related
Dec 6, 2012
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
View 1 Replies
View Related
Jan 21, 2012
i have tried many things i have tried to reset my router with the cmd prompt i have checked my drivers i have tried the simple things and at this point.
View 1 Replies
View Related
Aug 14, 2011
I'm using a RV082 and have about a dozen users on my network.Occasionally, when a user is accesssing a website like yahoo.com, twitter.com, cnn .com, etc, the web page only loads half way. Most often the page is missing stylesheets and/or images. Called Cisco support and they adjusted the MTU size to 1492 from 1500.Have a looked at the bandwidth report from my ISP and it shows nothing out of the ordinary, no spikes or surges in d/u. Have set LAN port to high priority, 100 Mbps, full duplex.. Seeing an error count around 327282.. which I don't understand.Why sites only partially load using this router?
View 1 Replies
View Related
Jun 24, 2012
I am trying to configure two inside interfaces without NAT. I am not using nat-control and I have added exemptions for the two networks. I can communicate between the two networks and to the Internet just fine.I would like to verify that NAT is disabled between the two interfaces. I also need to make sure that the Interface IP (specifically for the traffic from inside-test to the inside network) is not added to packets between the two networks. I would like to be able to verify this as well. In other words I need to have the Source IP address from the originating connection on the inside-test network passed along through to the Inside network device without being replaced by the Interface's IP address. This is a test config for a production environment that will be using a load balancer. The config I have may be working in this regard and the load balancer may be replacing this IP address (that is what I am trying to test), but I am not certain.So far I have the following NAT related running-config command (in regards to these two interfaces):
access-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0access-list NAT_Exempt_2 extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list NAT_Exempt_2nat (inside) 1 0.0.0.0 0.0.0.0nat (Inside-test) 0 access-list NAT_Exemptnat (Inside-test) 1 0.0.0.0 0.0.0.0
global (outside) 1 interfaceglobal (Inside-test) 1 interface
View 11 Replies
View Related
Apr 8, 2013
We've put in a 3750 at our corp hq (Detroit). We did this to break up the current flat 172.16.0.0 /16 network into separate VLAN's for various purposes. We plan on doing that at another site (Farmington), which will become a DR site. We are running EIGRP throughout the organization over an OPTEMAN netowrk and also sending routes to a managed MPLS network which uses BGP. BGP redistributes into EIGRP and vice versa. I've attached a pdf of the network. The 3750 core at the corp hq is a temp core, hopefully upgrading to Nexus within a year or two. This problem didn't exist until the 3750 was introduced and became the gateway for the site. The OPTEMAN router was the gateway and was on the same VLAN as the MPLS router.
So, in detroit we have an Detroit-MPLS router, Detroit-3750, and Detroit-OPTEMAN. What I'm seeing is that the routers I'm getting from the MPLS router make it to the 3750. The 3750 advertises those routes to the Detroit-OPTEMAN router. However, the OPTEMAN router doesn't advertise these routes any further..
In Farmington, it is currently set up like Detroit used to be set up. There is a flat network and both routers are on the same VLAN, no L3 core switch. Routes come in from the MPLS, get advertised to the Farmington-OPTEMAN router, distributes the routes out to all OPTEMAN connected routers, including Detroit. However, Detroit is not passing that route to the 3750.
When we made the 3750 stack the core, we didn't change anything else, except for some IP changes. Why these routes aren't fully redistributing?
Detroit-3750 Stack
WS-C3750G-24TS-S <-Stack master running c3750-ipservicesk9-mz.122-55.SE7.bin
WS-C3750X-12S-E <-Running c3750e-universalk9-mz.122-55.SE7
show sdm prefer
The current template is "desktop routing" template.
[Code]...
View 6 Replies
View Related
Nov 27, 2011
My computer (running windows XP and connected to the internet with a D Link USB adapter) refuses to load any webpages: despite showing full signal strength and connection in both the D Link settings and the windows XP wireless panel.I am able to ping websites and other computers in the house (all of which are able to access the internet) but no pages load in any browser I try.
View 1 Replies
View Related
Jun 2, 2013
let me know the exact meaning of attach ( yellow marked one)? the contractor was saying "it doesn't mean two switches as there is a built in redundancy in Cisco switch)"I don't think he is correct as I never heard about built in redundancy in Cisco Router/switchAny comment as this will affect the numbers from 55 (3750 v2) to 110....
View 41 Replies
View Related
Jun 21, 2011
What is supported in terms of running a mixed feature set in a Cisco 3750 switch stack.We are looking at setting up a stack consisting of 5 x 3750V2 and 2 x 3750G. Due to a requirement for full EIGRP we need the IP Services feature set. Is it a supported configuration to run with 2 or 3 switches running the IP Services feature set as stack masters and the others running IP Base? I understand that if stack master priorities were set these switches with the higher feature set could manage the stack and offer IP Services accross the stack. If we were to lose all of the switches running IP Services the stack would drop back to IP Base.I am looking for guidance as to if this is a supported configuration and not in breach of licensing? Is this likely to cause any problem other than above now and for future IOS releases?
View 2 Replies
View Related
Nov 11, 2012
We have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
View 2 Replies
View Related
Feb 17, 2010
Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...? Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.
View 3 Replies
View Related
Dec 9, 2012
We are doing a study on our public WiFi to identfy client connections based on wireless Vendor. about 40-50% of the clients wireless Vendors are "unknown". Is there a way to update the list of Vendor mac-addresses in WCS?
View 5 Replies
View Related
Dec 31, 2012
I have a Fujitsu Lifebook Series E that used to connect to the internet but will not connect now. It will not recognize or list any wireless connections available. Actually, I can't even pull up an empty list of wireless connections available. It does have a local area connection but it says a network cable is unplugged. I know it may be a faulty wireless card but I don't know how to test it or, if it is bad, where the find it to replace it.
View 14 Replies
View Related
Jul 11, 2012
i can't find my wireless network in the list. It shows me networks from my are but not my one. I know my one works and has no problem as my sister can use her laptop wirelessly
View 19 Replies
View Related
Jul 12, 2012
We have enabled web Auth for our public access on Cisco WLC 2504. It works fine. However, if a wireless user opens his email with download pictures website, he can’t get the picture download until he accept the web policy. Our users complaint about that.
"Our application makes requests to the internet to check for and download pictures, etc. The problem is that web requests are not permitted until a user has opened his/her web browser and attempted to go somewhere (e.g. google) so that your security system can redirect them to the authorization form where they must click the “accept” button. If the user has not done this yet, any functionality in our app that requires an internet connection won’t work because the security system is blocking the requests. Unfortunately, since they’re not in a web browser at the time, it doesn’t redirect them to the authorization page - the request simply fails since a redirect doesn’t have an effect on the application like it would a web browser. My remedy would be, if possible, to whitelist web requests to the server(s) where our code and/or images will live and let them get around that restriction. Otherwise, users won’t understand why the app isn’t working unless they try and open a web browser first – which is probably not something I’d expect them to do. With this solution, you could still ensure that nobody is accessing the internet at large without accepting your terms – but they could access your website as well as our application’s functionality seamlessly."
Can we setup whitelist or something like that on WLC?
View 9 Replies
View Related
May 21, 2013
I'm doing a project on trilateration in which is required to list the BSSID and power levels from the APs, since we have alot of Cisco Aironet 1100 deploye here, could this be a choice ?
My first try is to get these values using snmp, but so far had no luck finding the right MIB. I don't think the console might be useful, will it ?
I know I'm assuming alot, that the Aironet enables for a 'iwlist' dump, and that these values can be retrieved through snmp. But seems something reasonable for them to have, even if I haven't found it.
View 5 Replies
View Related
May 30, 2011
Every day or two my landlord's router just seems to disappear altogether . just seems to turn itself off randomly. Unplugging to reset results in good, clear signal for a while, but the problem always comes back. It affects all connected machines (not sure if it makes any difference if a macnine is connected via wire.)
View 4 Replies
View Related
Dec 22, 2011
My wireless router will no longer appear on the list of available networks, but it can find others. My partner's laptop will find it instantly! So it's obviously something on my computer.
OS: Vista Ultimate
Internet Provider: Sky
Country: UK
View 3 Replies
View Related
Jan 17, 2011
I recently added several devices to my wireless-g network: Xbox 360, an HTC Smart phone, and an old laptop my buddy gave me (in addition to the 2 desktops that were already on the network). Since doing this, I've had occasional buffering problems when streaming music or video, even when I'm only using 1 of the devices. I suspect that the Xbox (or maybe phone) is downloading updates in the background, even when it's turned off, and that is consuming bandwidth. Is there any way I can see a list of devices that are connected to the network and maybe even the amount of data being transmitted to/from each so I can find the culprit. when I play online, it says that my NAT settings are not open and that this makes it take longer to connect to other players. What are the risks involved in loosening the NAT restrictions?
View 1 Replies
View Related
Mar 17, 2012
I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable.
View 18 Replies
View Related
Jan 23, 2013
We are thinking of buying a WAP321 to use for captive portal.
Is it possible to configure it so that multiple guests and use the same username and password simultaneously?
If we have 10 guests in the office we don't want to configure 10 usernames for them to use.
View 1 Replies
View Related
