Having troubles loading a certificate in System security/802.1X Supplicant. I tried to upload *.car and *.msc certificates, but the device aborted the upload at each attempt.
View 2 Replies
I have two Cisco WLC 5508 controllers that I'm trying to set-up for our new corporate WLAN. I've gone through most of the configuration fine but have ran into an issue uploading a signed certificate to one of my controllers. I should point out that I have managed to upload the certificate successfully to one of the controllers, I just can't seem to upload it to the second.The issue is as follows:
- I've logged into the controller, gone to Security -> Web Auth -> Certificate -> Download Certificate
- I've specified my tftp server details and selected apply
- the process begins and I can see through my tftp client that the controller is attempting to copy and install the certificate
- The controller tries to install the certificate but fails, reporting the same
I'm trying to connect to my wireless network using an android device with certificate but with no success.I'm using a WLC4402 7.0.235.3 SSID Security (WPA2 Auth802.1X + CCKM) [code]
View 7 Replies View RelatedI’m trying to configure EAP-Fast following the guide [URL].But when I try to download the certificate, I receive the follow message: “Error installing certificate.”At logs I see:
*TransferTask: Sep 27 14:00:09.479: %UPDATE-3-CERT_INST_FAIL: Failed to install Webauth certificate. rc = 1
*TransferTask: Sep 27 14:00:09.479: %SSHPM-3-KEYED_PEM_DECODE_FAILED: Cannot PEM decode private key
- Remembering I’m doing Device Certificate.
My environment is:
WLC 2106 Windows 2003 with AD and CA When I try to use line commands I can’t too.
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
IP_ADDRESS: 10.10.10.1
> IP_SUBNET_MASK: 255.255.255.0
> DEFAULT_GATEWAY: 10.10.10.10
> TFTP_SERVER: 10.10.10.10
> TFTP_FILE: c2600-js-mz.122-15.T16.bin
> ....
> ARP: ADDRESS RESOLUTION for 10.10.10.10 timed out
> ARP failed with failure code 1. TFTP transfer aborted.
I connected cross cable between router and my pc and i put image of router in tftp_file with tftp server so when the router wants confirm y or n and i make y so my connection area connect and disconnect and never make connection with router so how can i slove it what are the steps in my pc and the router i used solarwinds tftp server ...
I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
There is ASA with remote access VPN and users are authenticated using third party signed certificates (CA is not local in ASA).When user certificate expires i can see it in syslog messages. For example:
%ASA-3-717009: Certificate validation failed. Certificate date is out-of-range, serial number: (...)
I would like to know if there is an opportunity to view user's certificate expiry date beforehand, say, 3 days before?
i am working on ISE 1.1.1, surprisingly i couldn't found certificate authority certifiate at certificate operation anymore.
would it be the change on GUI? So now where i can import the CA certificate to ISE?
I'm using two WAP321 with 4 VLANS
VLAN 100 - WPA PSK
VLAN 101 - WPA Radius
VLAN 102 - open (captive portal)
VLAN 103 - Management (no wifi)
Everything worked fine until I activated clustering on both devices yesterday. Since then, I can't connect via wifi anymore. I still have access to the management via ethernet. It seems like the wifi clients are not able to reach the Portal, Radius or DHCP Server anymore.
I have a WAP321. The unit hangs about on every day. Web interface and WLAN let not respond anymore. By a reset the unit will be back. I have put all unnecessary stale. Tracing the turned on, I can say nothing flashy.
View 11 Replies View Relatedwhere to go to get my WAP321's captive portal. If i type the IP address of the WAP321 it simply takes me into the Administration page.
View 1 Replies View RelatedWe need U-APSD (a special WMM Feature).Does the WAP321-E-K9 Support this feature?We need it for powersave mode from cordless wlan phones.
View 1 Replies View RelatedAny info if the WAP321 is any good? Do they have the dropping connections problem that the WAP4410n's do.I can't afford to buy another lemon.
View 2 Replies View RelatedMy current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies View RelatedI just bought 6 Cisco WAP321.
What I want is to have 1 SSID for all 6 WAP so all employee from 2 floor building can access.
WAP # 1 connect to LAN with cabe and setup as Master with WDS Bridge enabled. WDS interface is also enable with MAC address input from WAP #2; WAP #3 & WAP#4.WAP #2 connect to WAP #1 via wireless with WDS Bridge enabled. WDS
[Code].....
How to configure multiple WAP321 Wifi at once? Because I need to configure around 100 APs and i want to know if there is any software from Cisco to do it, like a WLC or something else.
View 6 Replies View RelatedI plan to use the WAP321 as a WLAN Hotspot. But I need more than one AP. What is the Design for this?
Do I need to configure every WAP321 with the captive portal and the user need to re-login every time they roam to another WAP321?
Or can I redirect all WAP321 AP to one captive portal?
It's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedWhen I connect to WAP321 only connects at 130 Mbps. Why?
View 3 Replies View RelatedWhat is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies View RelatedI have configured my WAP321 with captive portal enabled but how to a get to the captive portal. If i browse to its web address and get back into the administration GUI and if i connect to the wireless connection configured on this AP it does the normal wireless login.
View 2 Replies View RelatedHow I install the WAP321 with repeater?
View 3 Replies View RelatedI was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's. Take a basic scenario of 3 AP's and a single SSID. I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP. Not quite as seamless as using aironet and a controller, but still pretty good.
Question 1 How does the WAP321 handle roaming? Obviously without the clustering feature you would have to configure each AP independently. But after setting them up, would it support roaming in a similiar way to the AP541N??
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
In summary I like the roaming capability of the AP541N but hate the large clunky form factor. I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming. A short disconnect isn't a concern as long as it reconnects on it's own. Wireless controllers are a little out of the price range for this setup.
I have a RVS4000 witch I use as router, and DHCP server. I have a WAP321 witch I have configured SSID with one VLAN. Both devices have fixed IP address. I can connect computer to the wifi access point. But the computer cannot get an IP address from the DHCP server of the RVS4000. If I set the IP configuration manually, it can get an access to the network and Internet.
With another wifi access point it works, the computer get an IP address for the DHCP.
What should I have to do to make my DHCP server works with my wifi access point ?
Any Cisco small business switch that would be capable of powering five WAP321's? I don't know the power profile on these AP but have noticed that the Poe injectors pump out 16.8 MAX watts. I can't find anywhere what the power profile is on WAP321 AP but ~17 WATTS seems to me to be quite high.
In fact, I was interested in the SF100D-16P which has a power budget of 64W over 8 ports... the price range is in my budget.
Does the SF100D-16P can power 5-6 WAP321's sufficiently?
Our iOS6 devices cannot connect to our Cisco Wi-Fi access points using our guest network settings, which involves a captive portal where they must enter their email address. When they select the guest network, they get the screen shown at the bottom of the screen. Prior to iOS6, they'd get the web page where they enter their email address and accept our terms of use. This is happening both on upgraded devices and iPhone 5 devices. We haven't changed anything with the access points.
View 11 Replies View RelatedI currently had 6 WAP321 setup in our work environment on 2 floor building as Single Point Setup cluster. When I do a 470MB ISO files transfer between the server and the laptop, the speed is very slow, rate at 130KBs and sometime it go up to 30Mbps.Is there anyway to tweek teh WAP to get FULL speed of wireless all the time?
View 5 Replies View RelatedI have a WAP321 here, which is running at firmware version 1.0.3.4. The E-Mail Alert setup works for me, meaing I receive notification E-Mails from the Access Point. I am wondering however, why those E-Mails are blank, meaning, I only receive header information (to, from, date, subject) but no body content. I was expecting to receive the error message as content of the E-Mail Alert.
View 5 Replies View RelatedI'm trying to configure a WAP321 so that I have the same SSID and WPA2 password on both the RV220W and the WAP321 so that i can reach all areas of my clients location.
View 1 Replies View RelatedWe put in place 4 devices. Everything is working five (apple IOS6+ not obv...). So when somebody is connecting he have to read our agreement, enter is full name and check the box. (is not personnal session...)How can i have log his name and access hours???? Because a saw is connected when is connected in live on : Captive Portal>Authenticated Clients .But i want to keep a log with this informations + the date/hour if possible.
View 1 Replies View RelatedAnother problem with WAP321 access point. I set up the captive portal for guest access. Connexion is going well, I got IP adress, but then, I open my webrowser to authentificate on the captive portal, and I get a nice "404 not found / file not found" page. If I put the IP adress of the access point in my webrowser, I can get the captive portal homepage. Why the redirection is not working automatically
View 16 Replies View Relatedi am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
