How to configure multiple WAP321 Wifi at once? Because I need to configure around 100 APs and i want to know if there is any software from Cisco to do it, like a WLC or something else.
View 6 RepliesI have a WAP321 I am trying to set up. It's connected to gi1/23 and the switch system mode is set to router. The rest of the network works just fine.I have an SG500-28p and the port. [code] On the WAP321 wizard, configured IP address on my management vlan and also configured the default SSID on that vlan. That works. (I plan to remove that one) Then I add the two SSIDs for vlan 20 and 22 (private and public access) and I can't associate to either of the two additional SSIDs. I haven't configured any other settings beyond the wizard and adding the other two SSIDs. I do want cisco mobile ios (jabber) to work on the private network and also do have a couple spa525g2s that need to connect wireless.
View 1 Replies View RelatedMy question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedI need to configure a WAP4410N for use on a small, very simple business network. There should be a corporate WLAN and a guest WLAN. The corporate WLAN should allow anyone connectd to it to access resources on the domain.
In front of the WAP is a cable modem/router and a basic Level 2 (web managed) switch. What do i have to do to segregate the corporate and guest networks.
I thought I would add the corporate WLAN to VLAN1 (assuming the default VLAN in the switch is VLAN1). Then I figured I could create the guest WLAN and assign it to VLAN2 which which will be controlled entirely by the 4410N (DHCP, DNS, etc.) Does this sound like the right way of going about things?
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedI have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies View RelatedCan I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedIs it possible to configure multiple ISPs in 3560? and These ISPs traffic should be forward different vlans & different ports. i need configure port wise DHCP also and using different ip addresses please, which device supports this application
View 2 Replies View RelatedI am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
At our organisation our routers all have at least 3 BGP peers, each from a different connectivity provider. The different providers that we use all have different internet transit CDRs. Is there a way that I can configure a priority for the 3 BGP peers on our routers so that outbound traffic to the internet is sent to the BGP peer from the provider with the highest CDR?
Routers are C2821
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
Can you configure multiple next-hop entries and have it perform load balancing?
Example
route-map test
match ip address test
set ip next-hop 1.1.1.1
set ip next-hop 2.2.2.2
i have 6509+FWSM(4.0.4) now i wanna use stite to stite and ez vpn in the fwsm (multiple context) multiple context mode in fwsm support ipsec vpn?
View 2 Replies View RelatedI have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View RelatedI'm using two WAP321 with 4 VLANS
VLAN 100 - WPA PSK
VLAN 101 - WPA Radius
VLAN 102 - open (captive portal)
VLAN 103 - Management (no wifi)
Everything worked fine until I activated clustering on both devices yesterday. Since then, I can't connect via wifi anymore. I still have access to the management via ethernet. It seems like the wifi clients are not able to reach the Portal, Radius or DHCP Server anymore.
I have a WAP321. The unit hangs about on every day. Web interface and WLAN let not respond anymore. By a reset the unit will be back. I have put all unnecessary stale. Tracing the turned on, I can say nothing flashy.
View 11 Replies View RelatedASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View Relatedwhere to go to get my WAP321's captive portal. If i type the IP address of the WAP321 it simply takes me into the Administration page.
View 1 Replies View RelatedWe need U-APSD (a special WMM Feature).Does the WAP321-E-K9 Support this feature?We need it for powersave mode from cordless wlan phones.
View 1 Replies View RelatedAny info if the WAP321 is any good? Do they have the dropping connections problem that the WAP4410n's do.I can't afford to buy another lemon.
View 2 Replies View RelatedMy current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies View RelatedI just bought 6 Cisco WAP321.
What I want is to have 1 SSID for all 6 WAP so all employee from 2 floor building can access.
WAP # 1 connect to LAN with cabe and setup as Master with WDS Bridge enabled. WDS interface is also enable with MAC address input from WAP #2; WAP #3 & WAP#4.WAP #2 connect to WAP #1 via wireless with WDS Bridge enabled. WDS
[Code].....
I plan to use the WAP321 as a WLAN Hotspot. But I need more than one AP. What is the Design for this?
Do I need to configure every WAP321 with the captive portal and the user need to re-login every time they roam to another WAP321?
Or can I redirect all WAP321 AP to one captive portal?
It's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedWhen I connect to WAP321 only connects at 130 Mbps. Why?
View 3 Replies View RelatedWhat is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies View RelatedI have configured my WAP321 with captive portal enabled but how to a get to the captive portal. If i browse to its web address and get back into the administration GUI and if i connect to the wireless connection configured on this AP it does the normal wireless login.
View 2 Replies View RelatedHow I install the WAP321 with repeater?
View 3 Replies View RelatedI was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's. Take a basic scenario of 3 AP's and a single SSID. I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP. Not quite as seamless as using aironet and a controller, but still pretty good.
Question 1 How does the WAP321 handle roaming? Obviously without the clustering feature you would have to configure each AP independently. But after setting them up, would it support roaming in a similiar way to the AP541N??
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
In summary I like the roaming capability of the AP541N but hate the large clunky form factor. I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming. A short disconnect isn't a concern as long as it reconnects on it's own. Wireless controllers are a little out of the price range for this setup.
I have a RVS4000 witch I use as router, and DHCP server. I have a WAP321 witch I have configured SSID with one VLAN. Both devices have fixed IP address. I can connect computer to the wifi access point. But the computer cannot get an IP address from the DHCP server of the RVS4000. If I set the IP configuration manually, it can get an access to the network and Internet.
With another wifi access point it works, the computer get an IP address for the DHCP.
What should I have to do to make my DHCP server works with my wifi access point ?