I have a WAP321. The unit hangs about on every day. Web interface and WLAN let not respond anymore. By a reset the unit will be back. I have put all unnecessary stale. Tracing the turned on, I can say nothing flashy.
View 11 RepliesI'm using two WAP321 with 4 VLANS
VLAN 100 - WPA PSK
VLAN 101 - WPA Radius
VLAN 102 - open (captive portal)
VLAN 103 - Management (no wifi)
Everything worked fine until I activated clustering on both devices yesterday. Since then, I can't connect via wifi anymore. I still have access to the management via ethernet. It seems like the wifi clients are not able to reach the Portal, Radius or DHCP Server anymore.
I have here a HP Pavilion g6 running Windows 7 with quite a strange issue. Once the wireless is turned on common programs e.g. Microsoft Word, Internet Explorer etc. stop responding. What I've tried:Scanning for viruses with Malwarebytes - None found Reinstalling the wireless driver Refreshing the network stack?
View 14 Replies View Relatedwhere to go to get my WAP321's captive portal. If i type the IP address of the WAP321 it simply takes me into the Administration page.
View 1 Replies View RelatedWe need U-APSD (a special WMM Feature).Does the WAP321-E-K9 Support this feature?We need it for powersave mode from cordless wlan phones.
View 1 Replies View RelatedAny info if the WAP321 is any good? Do they have the dropping connections problem that the WAP4410n's do.I can't afford to buy another lemon.
View 2 Replies View RelatedMy current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies View RelatedI just bought 6 Cisco WAP321.
What I want is to have 1 SSID for all 6 WAP so all employee from 2 floor building can access.
WAP # 1 connect to LAN with cabe and setup as Master with WDS Bridge enabled. WDS interface is also enable with MAC address input from WAP #2; WAP #3 & WAP#4.WAP #2 connect to WAP #1 via wireless with WDS Bridge enabled. WDS
[Code].....
How to configure multiple WAP321 Wifi at once? Because I need to configure around 100 APs and i want to know if there is any software from Cisco to do it, like a WLC or something else.
View 6 Replies View RelatedI plan to use the WAP321 as a WLAN Hotspot. But I need more than one AP. What is the Design for this?
Do I need to configure every WAP321 with the captive portal and the user need to re-login every time they roam to another WAP321?
Or can I redirect all WAP321 AP to one captive portal?
It's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedWhen I connect to WAP321 only connects at 130 Mbps. Why?
View 3 Replies View RelatedWhat is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies View RelatedI have configured my WAP321 with captive portal enabled but how to a get to the captive portal. If i browse to its web address and get back into the administration GUI and if i connect to the wireless connection configured on this AP it does the normal wireless login.
View 2 Replies View RelatedHow I install the WAP321 with repeater?
View 3 Replies View RelatedI was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's. Take a basic scenario of 3 AP's and a single SSID. I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP. Not quite as seamless as using aironet and a controller, but still pretty good.
Question 1 How does the WAP321 handle roaming? Obviously without the clustering feature you would have to configure each AP independently. But after setting them up, would it support roaming in a similiar way to the AP541N??
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
In summary I like the roaming capability of the AP541N but hate the large clunky form factor. I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming. A short disconnect isn't a concern as long as it reconnects on it's own. Wireless controllers are a little out of the price range for this setup.
I have a RVS4000 witch I use as router, and DHCP server. I have a WAP321 witch I have configured SSID with one VLAN. Both devices have fixed IP address. I can connect computer to the wifi access point. But the computer cannot get an IP address from the DHCP server of the RVS4000. If I set the IP configuration manually, it can get an access to the network and Internet.
With another wifi access point it works, the computer get an IP address for the DHCP.
What should I have to do to make my DHCP server works with my wifi access point ?
Any Cisco small business switch that would be capable of powering five WAP321's? I don't know the power profile on these AP but have noticed that the Poe injectors pump out 16.8 MAX watts. I can't find anywhere what the power profile is on WAP321 AP but ~17 WATTS seems to me to be quite high.
In fact, I was interested in the SF100D-16P which has a power budget of 64W over 8 ports... the price range is in my budget.
Does the SF100D-16P can power 5-6 WAP321's sufficiently?
Our iOS6 devices cannot connect to our Cisco Wi-Fi access points using our guest network settings, which involves a captive portal where they must enter their email address. When they select the guest network, they get the screen shown at the bottom of the screen. Prior to iOS6, they'd get the web page where they enter their email address and accept our terms of use. This is happening both on upgraded devices and iPhone 5 devices. We haven't changed anything with the access points.
View 11 Replies View RelatedI currently had 6 WAP321 setup in our work environment on 2 floor building as Single Point Setup cluster. When I do a 470MB ISO files transfer between the server and the laptop, the speed is very slow, rate at 130KBs and sometime it go up to 30Mbps.Is there anyway to tweek teh WAP to get FULL speed of wireless all the time?
View 5 Replies View RelatedI have a WAP321 here, which is running at firmware version 1.0.3.4. The E-Mail Alert setup works for me, meaing I receive notification E-Mails from the Access Point. I am wondering however, why those E-Mails are blank, meaning, I only receive header information (to, from, date, subject) but no body content. I was expecting to receive the error message as content of the E-Mail Alert.
View 5 Replies View RelatedI'm trying to configure a WAP321 so that I have the same SSID and WPA2 password on both the RV220W and the WAP321 so that i can reach all areas of my clients location.
View 1 Replies View RelatedWe put in place 4 devices. Everything is working five (apple IOS6+ not obv...). So when somebody is connecting he have to read our agreement, enter is full name and check the box. (is not personnal session...)How can i have log his name and access hours???? Because a saw is connected when is connected in live on : Captive Portal>Authenticated Clients .But i want to keep a log with this informations + the date/hour if possible.
View 1 Replies View RelatedAnother problem with WAP321 access point. I set up the captive portal for guest access. Connexion is going well, I got IP adress, but then, I open my webrowser to authentificate on the captive portal, and I get a nice "404 not found / file not found" page. If I put the IP adress of the access point in my webrowser, I can get the captive portal homepage. Why the redirection is not working automatically
View 16 Replies View Relatedi am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
Our brand new WAP321 is configured manually because the setup wizard would not complete, just hangs at the end.
Anyway, when a client connects to the AP, it cannot get an IP address. It is able to connect to the AP but does not pickup an IP from our internal DHCP server. I've been up and down tthe config screens and even tried hard resetting the AP and starting from scratch to no avail. This happens with 2.4Ghz and 5 Ghz modes.
I've tried laptops and smartphones with the same result.
I want to setup my wap321 to not go to the Captive potal login page ,I want everyone to be authenticated automatically. I just want them to be redirected to my home page the first time they try and visit any page.i have the CP setup but I dont see any way to not request a user page and just redirect.I am using the latest firmware.
View 2 Replies View RelatedI need to limit access to two ip address via acl but when i add them to the list i lose access to internet.
View 1 Replies View RelatedMy company has an RV180W Router, a SGE-2000 Managed Switch, and a WAP321 Wireless Access Point. I have about 12 users on a Windows 2003 Server Standard, completely updated. My Win box is my DHCP Server. Now I am running two VLANS, Vlan 1 (default) the main vlan is where the Win box is on. Vlan 5 (guest Vlan) uses the RV180W as the DHCP server.
-Vlan1 is 192.168.1.1-254 - Issued by Win box
-Vlan5 is 192.168.2.100-254 - Issued by RV180W
I have a wi fi sky adapter,and when i plug it in,it says installing driver software. But..then it just hangs there,and eventually leads to-driver was not sucessfully installed(that is when i plug it out,but i waited more than an hour before that)I tried uninstaling and updating the driver for it,but it didnt worked.When i tried to uninstal the driver,again it just hanged.That is untill i unpluged the adapter..I have manually downloaded the latest driver,and when i check in properties it says that device is working properly.
View 19 Replies View RelatedRegion : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : BSNL
I Bought this w8968 a month back.. It was working alright till a few days back. When i connect and start browsing or downloading, it goes OK.. but after a few hours(sometimes 2, sometimes 1), It stops responding and I couldn`t ping 192.168.1.1 either through WiFi/Ethernet. Status indicators for DSL/WIFI/Internet/LAN all glowing as though nothing wrong with them..? The router is not that much hot when this happens.. When i switch off the router and then on, The Prob gets solved only to reappear again in 1/2/3 hrs..
Have been trying for the past two days to install a new E4200. It gets to 25% in the setup and then errors out and says I need to contact customer service.
Connecting through a brand new DSL modem that I know works as I can get access through my old router.
My PC (Windows 7) is directly connected to the router. I got to the point where I named the router in the install process the first time, but then it hung.
Have tried to use the CD to re-setup with no success. I've tried the hard reset holding in the button for 10 seconds and unplugging but nothing has changed.
I have a WAP321 I am trying to set up. It's connected to gi1/23 and the switch system mode is set to router. The rest of the network works just fine.I have an SG500-28p and the port. [code] On the WAP321 wizard, configured IP address on my management vlan and also configured the default SSID on that vlan. That works. (I plan to remove that one) Then I add the two SSIDs for vlan 20 and 22 (private and public access) and I can't associate to either of the two additional SSIDs. I haven't configured any other settings beyond the wizard and adding the other two SSIDs. I do want cisco mobile ios (jabber) to work on the private network and also do have a couple spa525g2s that need to connect wireless.
View 1 Replies View Related