Cisco Wireless :: Workgroup Bridge Between WRVS440n And WAP321?
Dec 4, 2012
i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
View 6 Replies
ADVERTISEMENT
Oct 30, 2012
My current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies
View Related
Feb 12, 2012
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction. Also attached is a result table of ping attempts through the ap1121wgb from each side. I don't have a problem with the wireless connections. The ap1121g's associate ok. Based on the ping results the problem appears to be in the ap1121g-wgb configuration. The following two cisco documents have been my main reference, besides the cisco command lookup site.URL
View 17 Replies
View Related
Nov 18, 2012
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies
View Related
Feb 21, 2012
We have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
View 1 Replies
View Related
Feb 16, 2013
I have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.
View 1 Replies
View Related
Apr 21, 2013
Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies
View Related
Mar 18, 2013
Any sample configuration of c1310 as a work group bridge.
View 2 Replies
View Related
Nov 14, 2012
I have Cisco 1242 setup as a work group bridge. Is there a rule of thumb on the max number of wired clients that can be connected at one time?
View 1 Replies
View Related
Feb 21, 2013
I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled. If I select the Access Point role from the GUI then the radio instantly becomes enabled. The same thing happens if I attempt the same procedure with the 2.4ghz radio as well. I can get the radios from both bands enabled if I select the Access Point role. I made sure to check that both radios were not set to workgroup bridge as well. I am running 12.4(25d)JA1 code on the AP. This is my first time working with this type of AP.
View 2 Replies
View Related
Aug 16, 2012
I need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies
View Related
Nov 5, 2012
EAP-TLS authentication for workgoup brdige fails.
Folloing is the log on ACS
Authentication failed
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain
12811 Extracted TLS Certificate message containing client certificate.
12814 Prepared TLS Alert message.
12817 TLS handshake failed.
[code]....
View 1 Replies
View Related
Jul 20, 2011
I have seen posts and screen shots of WRVS4400N settings screens showing WDS but I can't find anywhere in my setup to enable WDS on my version 1. I am running firmware 1.1.13. This makes me think WDS is only supported on v2 of the WRVS4400N, is that correct?
View 1 Replies
View Related
Feb 17, 2013
I have found log from IPS on router WRVS4400N and most of attacks i am getting from 0.0.0.0 IP adress. Is it normal?
View 1 Replies
View Related
Apr 14, 2013
I have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies
View Related
Dec 5, 2012
I'm using two WAP321 with 4 VLANS
VLAN 100 - WPA PSK
VLAN 101 - WPA Radius
VLAN 102 - open (captive portal)
VLAN 103 - Management (no wifi)
Everything worked fine until I activated clustering on both devices yesterday. Since then, I can't connect via wifi anymore. I still have access to the management via ethernet. It seems like the wifi clients are not able to reach the Portal, Radius or DHCP Server anymore.
View 5 Replies
View Related
Feb 17, 2013
I have a WAP321. The unit hangs about on every day. Web interface and WLAN let not respond anymore. By a reset the unit will be back. I have put all unnecessary stale. Tracing the turned on, I can say nothing flashy.
View 11 Replies
View Related
May 9, 2011
My partner and I have 2 notebook PCs and we have a wireless moden/router. I used to see my partner's PC in the Workgroup and share the printer before I reloaded windows XP Home in partner's PC. I added his PC to the Workgroup but can't see him in Workgroup from my PC anymore?
View 2 Replies
View Related
Jul 21, 2011
I have an older Linksys 11g router, two pc's with Windows 7 and a bunch of PC's with Windows XP that I need to LAN.Is there a simple way to do it?
View 1 Replies
View Related
Mar 5, 2013
where to go to get my WAP321's captive portal. If i type the IP address of the WAP321 it simply takes me into the Administration page.
View 1 Replies
View Related
May 7, 2013
We need U-APSD (a special WMM Feature).Does the WAP321-E-K9 Support this feature?We need it for powersave mode from cordless wlan phones.
View 1 Replies
View Related
Apr 24, 2012
Any info if the WAP321 is any good? Do they have the dropping connections problem that the WAP4410n's do.I can't afford to buy another lemon.
View 2 Replies
View Related
Oct 10, 2012
I just bought 6 Cisco WAP321.
What I want is to have 1 SSID for all 6 WAP so all employee from 2 floor building can access.
WAP # 1 connect to LAN with cabe and setup as Master with WDS Bridge enabled. WDS interface is also enable with MAC address input from WAP #2; WAP #3 & WAP#4.WAP #2 connect to WAP #1 via wireless with WDS Bridge enabled. WDS
[Code].....
View 15 Replies
View Related
Nov 26, 2012
How to configure multiple WAP321 Wifi at once? Because I need to configure around 100 APs and i want to know if there is any software from Cisco to do it, like a WLC or something else.
View 6 Replies
View Related
Aug 15, 2012
I plan to use the WAP321 as a WLAN Hotspot. But I need more than one AP. What is the Design for this?
Do I need to configure every WAP321 with the captive portal and the user need to re-login every time they roam to another WAP321?
Or can I redirect all WAP321 AP to one captive portal?
View 6 Replies
View Related
Oct 11, 2012
It's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies
View Related
Oct 17, 2012
When I connect to WAP321 only connects at 130 Mbps. Why?
View 3 Replies
View Related
Apr 24, 2013
What is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies
View Related
Mar 6, 2013
I have configured my WAP321 with captive portal enabled but how to a get to the captive portal. If i browse to its web address and get back into the administration GUI and if i connect to the wireless connection configured on this AP it does the normal wireless login.
View 2 Replies
View Related
Mar 21, 2012
How I install the WAP321 with repeater?
View 3 Replies
View Related
May 21, 2012
I was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's. Take a basic scenario of 3 AP's and a single SSID. I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP. Not quite as seamless as using aironet and a controller, but still pretty good.
Question 1 How does the WAP321 handle roaming? Obviously without the clustering feature you would have to configure each AP independently. But after setting them up, would it support roaming in a similiar way to the AP541N??
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
In summary I like the roaming capability of the AP541N but hate the large clunky form factor. I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming. A short disconnect isn't a concern as long as it reconnects on it's own. Wireless controllers are a little out of the price range for this setup.
View 3 Replies
View Related
Dec 10, 2012
I have a RVS4000 witch I use as router, and DHCP server. I have a WAP321 witch I have configured SSID with one VLAN. Both devices have fixed IP address. I can connect computer to the wifi access point. But the computer cannot get an IP address from the DHCP server of the RVS4000. If I set the IP configuration manually, it can get an access to the network and Internet.
With another wifi access point it works, the computer get an IP address for the DHCP.
What should I have to do to make my DHCP server works with my wifi access point ?
View 17 Replies
View Related
Jul 19, 2012
Any Cisco small business switch that would be capable of powering five WAP321's? I don't know the power profile on these AP but have noticed that the Poe injectors pump out 16.8 MAX watts. I can't find anywhere what the power profile is on WAP321 AP but ~17 WATTS seems to me to be quite high.
In fact, I was interested in the SF100D-16P which has a power budget of 64W over 8 ports... the price range is in my budget.
Does the SF100D-16P can power 5-6 WAP321's sufficiently?
View 5 Replies
View Related
