I need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 RepliesWhat kind of hardware are people using for mobile bridges? I have not had good luck with Cisco 1242's in bridge mode with mobile-client enabled. The only reason we're using the Cisco access point over standard industrial bridges is because we need to manually forward the mac addresses of the devices behind the bridge. These are being installed on robotic forklifts. They have a generic ethernet scrolling marquee installed that does not maintain any active connections and drops from the fowarding table in the bridge if not staticly configured. I'm looking for an alternative because the roaming is not nearly as smooth as it should be.
View 3 Replies View RelatedI have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
Who knows the best version (DD-WRT or other) to repeat the wireless signal with a E3000?At worst, a client bridge mode could be sufficient for my needs...
View 9 Replies View RelatedMy current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies View Relatedi am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
Our brand new WAP321 is configured manually because the setup wizard would not complete, just hangs at the end.
Anyway, when a client connects to the AP, it cannot get an IP address. It is able to connect to the AP but does not pickup an IP from our internal DHCP server. I've been up and down tthe config screens and even tried hard resetting the AP and starting from scratch to no avail. This happens with 2.4Ghz and 5 Ghz modes.
I've tried laptops and smartphones with the same result.
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies View Relateda customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies View RelatedWe have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
View 1 Replies View RelatedI'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
I have a WLC2504 and 2 LAP1261N (converted from autonomous to lightweight) with release 7.0.116.0 and I want to create a point-to-point mesh link between the 2 APs. When trying to change the APs mode from local to bridge I receive the message "This AP does not support bridge mode" even if the release notes say that mesh is supported on AP1261N. I tried to change the mode from gui and also from CLI.
View 12 Replies View RelatedI have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.
View 1 Replies View RelatedI am configuring a mobile van that is used for a mobile health clinic to drive to several locations and when pulling into an allocated parking spot the van will connect via wireless automatically. I am using autonomous 1252 AP's and am considering either briding or workgroup bridging.
The issue I am encountering is that the AP inside a van is a router that has to do DHCP across the wireless and because the ethernet interface between router and AP in the van never goes down the router does not know to re-DHCP. I remember from way back there was an IOS command to track a serial interface and drop the ethernet if the serial link goes down. Is there an equivalent command for AP's to drop the ethernet interface if the radio interfaces go down?
I'm using the 2106 in one environment with ROOT AP and MESH AP and when i put these in the Bridge mode, when one client connects to them it isn't working well, sometimes i can reach the client and sometimes not.
I tried it with an Access Point that connect with the ROOT AP or MESH AP and will do an ethernet bridging with another wired client (camera), what happens is very strange because sometimes i can reach the bridge client and sometimes i can reach the Access Point that is doing the bridge. I can't access the two clients at the same time. In this situation i lose the images from camera when i have access to the Access Point and when i get the images from camera i lost access with the Access Point.
When i put the ROOT AP in the H-REAP mode Local Switching with AP 1142 or AP1552, the clients connects well and the bridge mode in the another access point works without problem, when i put the H-REAP in Central Switching i have the same problem.
I'm using in the 2106 WLC the version 7.0.240.0.
I try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View RelatedI want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies View RelatedI have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
[code] Can't find any wrong with the switch ports and AP's that can result in Duplex mismatch.The only difference I can find is the AP that is in all duplex missm. log's is used for other Mesh AP's to connect to.
View 8 Replies View RelatedWe have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies View RelatedI am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
I have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.
Is it possible to connect two WAP200E on bridge mode without external antennas if they are 200 mts. (219 yard) apart?
View 2 Replies View RelatedIs there a way to set up these ap's to bridge. Ie two buildings 100 yards apart Both buildings have wired clients into a Cisco poe switch. Want to plug the ap's into each switch and have them bridge the data and even better if they could trunk vlans. No wireless clients at all. Strictly a point to point bridge. Also will they need to be lwaps or standalone APs. If they are lwaps can I flash to standalone ?
View 3 Replies View Relatedi would like to know if wap200e will still have connection if there are trees in between. because we have 2 offices that is 200 meters apart and trees all over them. i just wanna know before we buy the unit.
View 1 Replies View RelatedI have a E4200 with 1.0.04 firmware that I've used for a while as a router in front of a cable modem. I have upgraded the modem to a Virgin Media SuperHub. I have connected my E4200's WAN port to one of the SuperHub's LAN ports and changed the E4200's mode to Bridged Mode.I can connect to the Internet wirelessly and wired on the SuperHub, but I can only connect to the Internet via the E4200 if I'm wired to it. The wireless will connect to the E4200, it gets allocated and IP address in the correct range and the gateway is shown as the SuperHub's IP address, and I can see the E4200's management website via wireless, but I cannot connect to anything beyond the E4200.
View 9 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies View RelatedAs I understand, the latest FW for the E4200 makes it possible to put he router into bridge mode. In this mode, I can use it as an access point. In bridge mode, should I then connect my router to the WAN port at the E4200?The other way to make the E4200 into an AP, is to disable DHCP and NAT and give the E4200 an IP address out of range for the DHCP range in my preferred router.
Choosing between this two option to make the E4200 into an AP, which is considered to be the best solution?And to be sure; using this option, then the Ethernet cable should be connected to the LAN port of the E4200? is the performance of an E4200 in AP mode the same as a dedicated AP like the WAP610N?
If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedJust bought 2 e4200's! I have the first one connected to the ATT router, and I have the second one connected to the first in Bridge Mode. It works great! It knew how to configure itself to be the down-level client.
However, I noticed that the port speed is only 100 Mbps on the port that is acting as the link for the bridge. I am running brand-new CAT5e thru the house, and if I connect the cable directly to my laptop - I get 1Gbps. So I know that the cable is good.
Is there a way to change the speed of the INET port on the down-level e4200?
Started setting up a Linksys EA4500 Yesterday.
- Bridge Mode
- Router Address Manually specified
- Manual wifi setup
Regular access works. My smartphone obtains IP address, connects, accesses pages.Guest access loops through the "obtain IP address" step. Bridge mode might have a bug?
I have just received my 2 new cheap wrt54g2 routers. I already have a router with dhcp in my network, so I just need this routers to connect wired net and wireless. Is there any way to use this routers as a bridge? Earlier I used asus router, with disabled dhcp and lan cable connected to one of lan ports. But this is not comfortable, because I need to put ip address to router statically
View 6 Replies View Related