Who knows the best version (DD-WRT or other) to repeat the wireless signal with a E3000?At worst, a client bridge mode could be sufficient for my needs...
View 9 Replies
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies View RelatedI have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
What is the difference between AP, Client and Repeater. There is a switch on the back of my Access Point and I just wanted a little bit of knowledge of what they are and what are the best situation I would use them in?
View 3 Replies View Related1) Apparently, my Cisco modem likes to assign new IP addresses to things, so I didn't figure out the web access page until an hour in (was NOT 192.168.1.245)
2) Do I input the same IP address, subnet, DNS and default gateway as my Cisco modem? It has a wireless router and switch bundled in, should I use the wireless network's MAC address or the wired?
Currently, it's set to 'automatically configure':
IPv4
Local IP Address: 192.xxx.x.xx
Subnet Mask: 255.xxx.xxx.x
Default Gateway: 192.xxx.x.x
Primary DNS: 64.xx.xxx.xxx
Secondary DNS: 0.0.0.0
I can access the page fine, but I cannot get the wireless client working...
3) I did a site survey and found my existing network and inputted its SSID and MAC address, but nothing happens. I still get one bar on my wireless devices indicating the AP isn't working.
I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread. The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.I've tried making them work as stand alone AP's, Bridge<-> Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.Ultimately, I need to make them work in AP<->Client-Repeater mode. I've not been successful in making them work in any mode for a prolonged period of time.
having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try. If it works, great, but then that would defeat the purpose of buying an N radio AP. I would like the potential 300Mbps throughput.
I've small corporate network with Cisco 800 as main DSL router/firewall/DHCP. I'd like to setup Linksys E3000 (firmware: 1.0.01) as bridge (no DHCP, only wireless repeater), but there is no "bridge mode" in E3000 interface
View 9 Replies View RelatedWhat kind of hardware are people using for mobile bridges? I have not had good luck with Cisco 1242's in bridge mode with mobile-client enabled. The only reason we're using the Cisco access point over standard industrial bridges is because we need to manually forward the mac addresses of the devices behind the bridge. These are being installed on robotic forklifts. They have a generic ethernet scrolling marquee installed that does not maintain any active connections and drops from the fowarding table in the bridge if not staticly configured. I'm looking for an alternative because the roaming is not nearly as smooth as it should be.
View 3 Replies View RelatedI have an E3000 router guest access set up via CD. Is is possible to set up a Security Mode setting on this rather than it being open to all. I cannot find anything for Admin to set this up, it seems a glitch in security?
View 1 Replies View RelatedI have a E4200 with 1.0.04 firmware that I've used for a while as a router in front of a cable modem. I have upgraded the modem to a Virgin Media SuperHub. I have connected my E4200's WAN port to one of the SuperHub's LAN ports and changed the E4200's mode to Bridged Mode.I can connect to the Internet wirelessly and wired on the SuperHub, but I can only connect to the Internet via the E4200 if I'm wired to it. The wireless will connect to the E4200, it gets allocated and IP address in the correct range and the gateway is shown as the SuperHub's IP address, and I can see the E4200's management website via wireless, but I cannot connect to anything beyond the E4200.
View 9 Replies View RelatedI bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies View RelatedAs I understand, the latest FW for the E4200 makes it possible to put he router into bridge mode. In this mode, I can use it as an access point. In bridge mode, should I then connect my router to the WAN port at the E4200?The other way to make the E4200 into an AP, is to disable DHCP and NAT and give the E4200 an IP address out of range for the DHCP range in my preferred router.
Choosing between this two option to make the E4200 into an AP, which is considered to be the best solution?And to be sure; using this option, then the Ethernet cable should be connected to the LAN port of the E4200? is the performance of an E4200 in AP mode the same as a dedicated AP like the WAP610N?
Just bought 2 e4200's! I have the first one connected to the ATT router, and I have the second one connected to the first in Bridge Mode. It works great! It knew how to configure itself to be the down-level client.
However, I noticed that the port speed is only 100 Mbps on the port that is acting as the link for the bridge. I am running brand-new CAT5e thru the house, and if I connect the cable directly to my laptop - I get 1Gbps. So I know that the cable is good.
Is there a way to change the speed of the INET port on the down-level e4200?
Started setting up a Linksys EA4500 Yesterday.
- Bridge Mode
- Router Address Manually specified
- Manual wifi setup
Regular access works. My smartphone obtains IP address, connects, accesses pages.Guest access loops through the "obtain IP address" step. Bridge mode might have a bug?
I have just received my 2 new cheap wrt54g2 routers. I already have a router with dhcp in my network, so I just need this routers to connect wired net and wireless. Is there any way to use this routers as a bridge? Earlier I used asus router, with disabled dhcp and lan cable connected to one of lan ports. But this is not comfortable, because I need to put ip address to router statically
View 6 Replies View RelatedI have a Wireless Router supplied by my ISP that give me both 1G Lan and N Band Wireless, so I just need to use my 4200V1 as a Storage Access Point. I have done all the Bridge Mode configurations, IP Address ad Subnet / Default Gateway, etc to the routher and can see it on my Local LAN, by it's Set name.
I can not http or Https to the Config menu in any way, so I can not establish if a Disk is connected or not. The Disk device is USB Connected to the E4200 port, but I can not acceeass any of the files that are on it.
DGW - 192.168.1.1
E4200 - 192.168.1.200
Bridge Mode
Wireless Disabled on both Bands
DHCP Disabled
Everything appears fine, but not able to bring up Advance Configuration interface .
I have just purchased t-mobile's at home phone service (voip) and they gave me a UTA200-TM Hiport Adaptor to connect for the service. Had Vonage (voip) for 2 years so know how it works and never had problems. This one however will only allow the phone line to stay on for about 30 seconds and then drop it. Have it connected to a modem (cable internet) and a WRT54GS Wireless Router. T-Mobile wants me to check to see if the router has bridge mode set up as they think that may be causing the phone line to drop out. How can I check that? I can not figure out the directions on the linksys site, too confusing.
View 3 Replies View RelatedI need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies View RelatedI have a new Linksys E3000, 2 wired disktops (1 windows 7, 1 windows vista), 2 wireless laptops (both windows Vista), whenever the computers power down into sleep mode and are woke up, I have lost my connections to the router and I am forced to restart the computer. I've been told by one person that this is a problem with vista and windows 7, but wouldn't that have been a problem with my old router also?
View 9 Replies View RelatedRestarting the e4200 did not work. Resetting using the switch at the back did not resolve the issue. I was able to reset it via the 192.168.1.1 web page. After restoring my settings from backup, the issue remained the same. This was not alleviated after I updated the firmware. Plugging into one of the ports with a cat5 cable with my Mac, I was able to get an IP, yet I was not able to surf; same case with my MacBook.
Doing the 30-30-30 reboot did not fix this issue and all the while the front white light on the router went and stayed, solid.To see if I could get this to do ANY sort of meaningful internetting (is that even a word?) I put the e4200 in bridge mode and when I put the cable modem in, and all that plugs into this router works. This, of course, means that there is:
1. No Wifi signal and
2. It will not reset to factory settings.
I configured the EA4500 to work in bridge mode, to use it as an accespoint for an existing network (Linksys WRT610N). It gets an IP address (192.168.1.141), but does not offer a wireless network (the ethernet ports do offer network acces). When I try to access the configuration on IP address 192.168.1.141 I get the Linksys Smart Wifi page asking for the password. When I enter the password, a message "Waiting" appears and that's all. It keeps me waiting forever and I cannot access the configuration settings.I have tried to reset the router (30sec. reset button, power off 30sec, power on) but the result is the same.
View 6 Replies View RelatedI'm using the E4200 in Bridge mode and it's handing out IPs from our DHCP server (not acting as it's own). I have about 8 people connecting to this wirelessly to get to our network. For some reason it locked up once every week or two and I have to unplug it (can't even remote into it).
View 3 Replies View RelatedI have four E4200 units on my network, each with an unique IP address, in bridge mode to act as a wireless mesh across my entire building. They are all connected to my central L3 switch, via their Internet ports.
Is it possible to enable the Guest network on each unit, to create a 'Guest Wifi' mesh (providing that I allow the 192.168.33.0 network to route across my network fabric), or will this not work because each indivudual AP will be assigning IP address 192.168.33.1 as it's gateway address meaning that I would have four distinct MAC addresses within the network, each trying to claim that they are IP 192.168.33.1?
I have an E4200V2 with the latest .36 firmware installed.The E4200V2 is setup in Bridge Mode. THe 4200 DHCP's an IP for itself from my network infrastructure. This consists of a UBEE DOCSIS 3 (gig E output) modem on a 100 meg cable connection feeding an IP Cop Linux router/firewall and out to a gig switch, fully gig E on the network side. The wired portion of the network is absolutely bulletproof. And the older B only AP that ran well was also on this same setup.I have the E4200V2 set for N only on the 5 GHz side, and I had it set to Auto for channel selection, but manually set an unused channel currently. The 2.5 GHz side is set also manually to a locally unused channel now, and is set to mixed mode as I have B/G/N devices I need to connect to. The unused channel for both radios was detemined by scanning for AP activity using one of my Linux laptops. I have both the 5 GHz and 2.5 GHz radios set for 20/40 channel width. And I am using the recommended WPA2-Personal for security on both, with a separate SSID name for each radio.
The wireless connection for both E4200 V2 radios disconnects on fairly random but regular times and has to reconnect. This happens on both radios. There is no interference, and no network feed issues that would cause this. And the older B only Orinoco AP I replaced never had these issues. Signals are strong to all of the devices and the dropouts occur even when testing with a laptop several feet from the E4200V2. If I am streaming a video over GoogleTV or music or playing an online game, the 4200 disconnects regularly and the devices need to reconnect. This happens on both radios and to every device.
The latest firmware seems to support bridge mode. Does it mean the router can connect to another router wirelessly in the bridge mode?
View 6 Replies View RelatedI just bought an E2500. Wanted to set it up in bridge mode. I can't seem to find any way of doing this.Cisco Knowledge Base article # 4194 shows what I am attempting to do.
View 1 Replies View RelatedWell I accidentally put the router in bridge mode. It's a e1200 or 2500 I'm not exactly sure. But I was wondering how I can get it out? I can't access the web interface at 192.168.1.1 however I can access my modem's interface at 192.168.254.254.
View 4 Replies View RelatedI have a Fiber to Ethernet connector from my ISP. The Ethernet cable goes to an iSP issued Zyxel router. Into this router the landline phoneservice connects to give us VoIP landline service (which is cheaper). An Ethernet cable goes from the Internet port on the E4200 to a LAN port on the Zyxel router. That works great but I had to put the E4200 into Bridge Mode to get it to connect to the Internet via the Zyxel router which I need to use the phone services my ISP provides. I bought the E4200 because I wanted to use the dualband functionally and get a 802.11N 5GHz network setup and to give me the ability to block certian websites and services which I knew Cisco/Linksys is famous for - the abillity to control your network.
Well then imagine my surprise when I could not use the Parental Control settings when the router is in Bridge Mode... This was the reason I bought this router over an Apple Airport Exreme. Is there anyway to get it to let me use the Parental Control anyway while in Bridge Mode or a better way for me to connect the router with the rest of my network?
I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
After updating the firmware of th EA6500 to Ver.1.1.28.146072 I have no longer access to the GUI options of Speed Test, Guest Access, Parental Controls, Media Prioritization and USB Storage. I have reset the router to factory default settings and still none of the items are showing on the web page the only options available are:Connectivity,Troubleshooting.Wireless.
View 5 Replies View RelatedI accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.
View 4 Replies View Related
