Cisco Wireless :: 1242 - Bridge Mode With Mobile-client Enabled
Sep 5, 2011
What kind of hardware are people using for mobile bridges? I have not had good luck with Cisco 1242's in bridge mode with mobile-client enabled. The only reason we're using the Cisco access point over standard industrial bridges is because we need to manually forward the mac addresses of the devices behind the bridge. These are being installed on robotic forklifts. They have a generic ethernet scrolling marquee installed that does not maintain any active connections and drops from the fowarding table in the bridge if not staticly configured. I'm looking for an alternative because the roaming is not nearly as smooth as it should be.
View 3 Replies
ADVERTISEMENT
Jul 27, 2011
I try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies
View Related
Apr 2, 2012
is it possible to share the same network segment like my LAN for mobile users? In a so called bridge mode? I got a VPN tunnel to a customer from my local network and i need to access it within the mobile access. I can not change the VPN Site to Site tunnel.
View 2 Replies
View Related
Dec 19, 2011
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
View 3 Replies
View Related
Jul 5, 2011
Who knows the best version (DD-WRT or other) to repeat the wireless signal with a E3000?At worst, a client bridge mode could be sufficient for my needs...
View 9 Replies
View Related
Aug 16, 2012
I need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies
View Related
Sep 12, 2007
Trying to authenticate a Wireless 1242 AP to a switch port with Dot1x enabled. It seems like the switch can't get the mac or doesn't ever start authentication for the port when I plug in an ap. The ap is configured to pull dhcp on start for fa 0, however never gets an address, even though the port should fail into guest network after auth fails.Any thoughts,, a debug only shows this...
*Mar 1 00:19:27.127: %IF-3-VLAN_NOT_CONFIGURED: Received dot1Q VLAN tagged packet on interface which does not have VLAN configured.
View 3 Replies
View Related
Apr 18, 2011
Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies
View Related
Oct 15, 2012
I have Eight AIR-AP1242AG-E-K9's accross our site that have 2 SSID's and 2 VLAN's that work well, I want to link one of the AIR-AP1242AG-E-K9 to another one using 5ghz patch antennas across a 50 metre gap, but I am puzzled on how to do this, as to create a root bridge and a non route bridge link I need to put the infrastucture SSID on and this must be on VLAN1 but I want the traffic from both VLANs to pass over this link. I just want to ensure the config will work as I need to go into a cherry picker to get to the non-root-bridge.
View 11 Replies
View Related
Jun 10, 2012
At intermittent times, we will have a single device start to "hide" behind a 1242 bridge.In the past, my team would reload or reboot the bridge, and everything would come back up.But the 90 seconds of lost data were causing problems.
I found the the WB was always available.So I would ping the hidden device from the WB, and it would ping.Next, I showed the ARP table, and got the MAC address of the hidden device.Then, I would start a ping from my PC, and leave it running. Constant "Destination Unreachables" from the router.Next, I showed the bridging table for F0, and sometimes the device would be there, sometimes not. I would add a forwarding bridging entry manualy, and exit conf.
Showing the briding table would show the device, with a "P"ermanent age, but still no pinging.Finally, I would remove the forwarding briding entry, and pings would start within a couple of seconds.During these periods, outbound UDP packets will continue to be forwarded from the PC.So, my managers want to convert everything to UDP, which is a potential disaster in my opinion. [code]
View 12 Replies
View Related
Nov 14, 2012
I have Cisco 1242 setup as a work group bridge. Is there a rule of thumb on the max number of wired clients that can be connected at one time?
View 1 Replies
View Related
Aug 13, 2006
i need to change the IOS in a Ligthwiegth Access point and make it work as an Autonomus AP 1242. I have got the image but im not realy clear about the process. I got to enter the Ligthwiegth Access point true the console port but i dont know how is the upgrading process.
View 6 Replies
View Related
Mar 8, 2012
we had a problem with a customer wlan in our warehouse (cannel overlapping). The troubleshoot needed a long time. For the future if requipred in case of problems i want to configure one access point in the warehouse as a scanner (please find picture in the attachement). The Autonomous cisco 1242 is now configured as scanner but i can't see any logfiles? Where can i find these informations. This is the cisco description of the scanner mode:Scanner—Functions as a network monitoring device. In the Scanner mode, the access point does not accept associations from clients. It continuously scans and reports wireless traffic it detects from other wireless devices on the wireless LAN. All access points can be configured as a scanner.
View 1 Replies
View Related
May 1, 2012
For the establishment of a WiFi Hot Spot with 5 Cisco 1242AG and 5 antenna AIR-ANT1728, I want to know what the config is the most suitable.
- One antenna in root mode and the other 4 in repeater mode
- Or 5 antennas in root mode
Between each terminal distance is about 100 meters outside?
View 3 Replies
View Related
May 31, 2013
However, I now have a number of devices... certain smartphones so far... that will NOT connect to a FlexConnect AP if it's a 1262AGN AP, but my older 1242G AP will accept the devices without issue. Same SSID, same encryption standards.
If I connect the devices to my guest network (no security), they will connect just fine to both APs, and Non-FlexConnect 1242 and 1262 APs will both accept the devices without issue using my private network.
In other words, it seems to be an issue specific to 1262AGN with my encryption security. My security is WPA2/AES with PSK. No additional security on the SSID.
View 19 Replies
View Related
Apr 14, 2011
I have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.
Prior to installation I bench tested that the repeaters would associate with the access points and if one of the access points was turned off the repeaters would automatically roam to another access point. I did not have all 9 devices powered up at the same time, but did have 2 repeaters and 2 access points powered up to simulate association and roaming.
During installation as access points and repeaters were powered up everything behaved as expected (repeaters were associating to access points etc.) however during installation once everything was installed the 3 access points were all powered down for half an hour or so and once powered back on the repeaters did not automatically re-associate until they were re-booted.
I have now configured the repaters with parent MAC addresses to reflect the above current assocaition pattern but not yet powered off the access points to test if this forces re-association as this is now a live operational site!!
Is it normal to have to re-boot the repeaters if ALL 3 access points are powered down at the same time? i.e. If only one access point is powered down will the repeaters automaically roam to another access point o.k.?
View 5 Replies
View Related
Oct 23, 2012
I want to connect with wireless devices two buildings, one in front of another. Short distance (about 20 meters) and no obstacles. I have a couple of aironet 1242 and i was wondering if it would be possible to setup this link with this equipment.
could WGB be the solution?
View 2 Replies
View Related
Aug 25, 2012
Well i am currently using a BSNL DNA A211-1 wifi modem-cum-router with a wireline inbetween my PC (win7 ultm) & the router, so as to connect to the internet. i use the wifi feature of my router to connect my samsung gts5570 wifi enabled phone as well as a few other wifi enabled devices, to use internet on them. now i was thinking whether i can connect my desktop pc to my mobile phone using this wifi router somehow? how can that be done since there is already 2 different network that exist between my pc & router thru wireline & my mobile & the router thru wifi, all i need is a way to sync these to networks into one, so that my pc & my mobile use internet & at the same time they connect to each other as well.
View 3 Replies
View Related
Apr 24, 2013
One of my customer has an Apple IPAD 2.The IPAD is getting registerd through Cisco WLC 7.2.The APs that are being used is AP 1252 & AP 1242. The AP are configured in flex mode. The issue that we are facing is all the laptops and IPADs other then Apple IPAD are working but the Apple IPAD are not working through AES WPA2.It gives him a dismiss message and at time it gets connected but take a long time to get connected. Incase when the IPAD gets connected the following happens.
While connecting to the SSID it will ask for the preshared keyAfetr entering the preshared key it takes time to acquire an IP addressAfter the IP address is assigned it gives a dismiss message. If we do not click on the dismiss message then it will take anothere 30 seconds or so and get connected.
View 1 Replies
View Related
Aug 17, 2012
I have a desktop PC where the only internet connection is via a 'USB mobile broadband dongle'.I have connected the PC via ethernet cable to the ethernet port on a d-link wifi router (which isn't connected to the internet).I'd like to be able to connect other non-PC devices (eg my mobile phone) to the router via wifi in order to connect to the internet.To do this, I gather that one possible solution is to bridge the LAN and dongle connections. My first problem is that in 'Network Connections', only my USBdongle connection is shown (see pic) - there is no icon for the LAN/ethernet. In device manager, the "Atheros AR5007EG Wireless Network Adapter" and "Realtek PCIe FE Family Controller" are both showing without any ?'s etc
Other info:I'm running Windows 7 Home Premium 64 on a HP Pavilion All-in-one MS200 desktop.
View 1 Replies
View Related
Nov 18, 2012
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies
View Related
May 26, 2013
a customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies
View Related
Feb 21, 2012
We have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
View 1 Replies
View Related
Mar 6, 2012
I'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
View 1 Replies
View Related
Apr 21, 2013
I have a WLC2504 and 2 LAP1261N (converted from autonomous to lightweight) with release 7.0.116.0 and I want to create a point-to-point mesh link between the 2 APs. When trying to change the APs mode from local to bridge I receive the message "This AP does not support bridge mode" even if the release notes say that mesh is supported on AP1261N. I tried to change the mode from gui and also from CLI.
View 12 Replies
View Related
Feb 16, 2013
I have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.
View 1 Replies
View Related
May 15, 2011
I am configuring a mobile van that is used for a mobile health clinic to drive to several locations and when pulling into an allocated parking spot the van will connect via wireless automatically. I am using autonomous 1252 AP's and am considering either briding or workgroup bridging.
The issue I am encountering is that the AP inside a van is a router that has to do DHCP across the wireless and because the ethernet interface between router and AP in the van never goes down the router does not know to re-DHCP. I remember from way back there was an IOS command to track a serial interface and drop the ethernet if the serial link goes down. Is there an equivalent command for AP's to drop the ethernet interface if the radio interfaces go down?
View 2 Replies
View Related
Mar 17, 2013
I'm using the 2106 in one environment with ROOT AP and MESH AP and when i put these in the Bridge mode, when one client connects to them it isn't working well, sometimes i can reach the client and sometimes not.
I tried it with an Access Point that connect with the ROOT AP or MESH AP and will do an ethernet bridging with another wired client (camera), what happens is very strange because sometimes i can reach the bridge client and sometimes i can reach the Access Point that is doing the bridge. I can't access the two clients at the same time. In this situation i lose the images from camera when i have access to the Access Point and when i get the images from camera i lost access with the Access Point.
When i put the ROOT AP in the H-REAP mode Local Switching with AP 1142 or AP1552, the clients connects well and the bridge mode in the another access point works without problem, when i put the H-REAP in Central Switching i have the same problem.
I'm using in the 2106 WLC the version 7.0.240.0.
View 11 Replies
View Related
Jun 16, 2011
I want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies
View Related
Sep 21, 2010
I have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
View 1 Replies
View Related
May 16, 2013
[code] Can't find any wrong with the switch ports and AP's that can result in Duplex mismatch.The only difference I can find is the AP that is in all duplex missm. log's is used for other Mesh AP's to connect to.
View 8 Replies
View Related
Jul 14, 2011
We have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies
View Related
Apr 3, 2013
I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
View 9 Replies
View Related
