Cisco Wireless :: AP1121G Workgroup Bridge
Feb 12, 2012
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction. Also attached is a result table of ping attempts through the ap1121wgb from each side. I don't have a problem with the wireless connections. The ap1121g's associate ok. Based on the ping results the problem appears to be in the ap1121g-wgb configuration. The following two cisco documents have been my main reference, besides the cisco command lookup site.URL
View 17 Replies
ADVERTISEMENT
Nov 18, 2012
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies
View Related
Feb 21, 2012
We have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
View 1 Replies
View Related
Feb 16, 2013
I have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.
View 1 Replies
View Related
Dec 4, 2012
i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
View 6 Replies
View Related
Apr 21, 2013
Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies
View Related
Mar 18, 2013
Any sample configuration of c1310 as a work group bridge.
View 2 Replies
View Related
Nov 14, 2012
I have Cisco 1242 setup as a work group bridge. Is there a rule of thumb on the max number of wired clients that can be connected at one time?
View 1 Replies
View Related
Feb 21, 2013
I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled. If I select the Access Point role from the GUI then the radio instantly becomes enabled. The same thing happens if I attempt the same procedure with the 2.4ghz radio as well. I can get the radios from both bands enabled if I select the Access Point role. I made sure to check that both radios were not set to workgroup bridge as well. I am running 12.4(25d)JA1 code on the AP. This is my first time working with this type of AP.
View 2 Replies
View Related
Nov 5, 2012
EAP-TLS authentication for workgoup brdige fails.
Folloing is the log on ACS
Authentication failed
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain
12811 Extracted TLS Certificate message containing client certificate.
12814 Prepared TLS Alert message.
12817 TLS handshake failed.
[code]....
View 1 Replies
View Related
Jul 6, 2011
When a ap1121G joins WLC4404,it shows a normal heatmap in WCS. But when a ap1121G joins WLC5508,the RSSI in whole coverage is almost -35 dbm.I copy the heatmaps to the attached files.
The versions are as below.
WCS 6.0.196
WLC5508 6.0.200.29
WLC4404 5.2.157
View 8 Replies
View Related
Feb 27, 2011
I want to convert LAP AIR-AP1121G-E-K9 to autonomous AP.
View 1 Replies
View Related
May 21, 2013
I want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x
View 4 Replies
View Related
Oct 4, 2011
In CLI we have users log in at priv 1 and use "enable" to increase privilege and do configurations. This allows "accounting" of command history. On the AIR-AP1121G-A-K9 (12.3(8)JED1) I cannot duplicate this for http login.
I can log in as a user at priv 1. When I try to go to a privileged link like "Security" I get prompted for a second login/pw. Nothing works here unless I have a second user defined at priv 15 and enter that login/pw. The problem is - that login/pw can be used to log in via http in the first place which bypasses accounting of the actual user. It also allows login to the CLI at priv 15 which I cannot permit.
username test1 secret 5 abcdxxx
username test2 privilege 15 secret 5 efghxxx
enable secret 5 ijklxxx(code)
View 1 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
May 9, 2011
My partner and I have 2 notebook PCs and we have a wireless moden/router. I used to see my partner's PC in the Workgroup and share the printer before I reloaded windows XP Home in partner's PC. I added his PC to the Workgroup but can't see him in Workgroup from my PC anymore?
View 2 Replies
View Related
Jul 21, 2011
I have an older Linksys 11g router, two pc's with Windows 7 and a bunch of PC's with Windows XP that I need to LAN.Is there a simple way to do it?
View 1 Replies
View Related
Jun 10, 2009
I have a wrt350n at home and it works fine but it has only one little issue. When I connect my lap wireless I cant see the other work group pcs but if I wire the laptop there is no problem. I use ip to share files and not net bios but sometimes it would be great to find all the pcs on the work group easily and not memorize all the ips.
Disabled firewalls, updated firmware, tried to change network ip... nothing solved. Have no problems at work with an WRT54G.
View 2 Replies
View Related
Nov 28, 2012
I have a win7 desktop upstairs with all of my media on it.I also have a winXP laptop that I would like to use as a media center running xbmc connected to my tv downstairs.I have set up a workgroup so my laptop can access the media stored on my desktop and everything works great when they are both hardwired to my router (Linksys E3000).However, as soon as I unplug my laptop from my router and switch to the wireless connection I can no longer ping my desktop or access the shared folder (internet still works fine on the laptop, it just cant see my desktop anymore).If I plug it back in to the router, everything works again.
The exact error message I get when I try to access the shared folder is "\INFINITYMedia is not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. [code]
View 14 Replies
View Related
Feb 21, 2013
Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Which WORKGROUP does router have for sharing? I need this, because I have WD TW live and want to access routers usb hdd through sharing. Because router media server only supports up to 100 files, I see no other solution.Is there anyway to set the workgroup
View 1 Replies
View Related
Dec 15, 2012
Region : Canada
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.12.22 Build 120424 Rel.39632n
ISP :
I can access the USB storage via FTP, but I wanted to access files using a Windows Explorer format. Also, anyone access the Media share ? Manual tells you how to setup the USB functions but not how to access from a PC.
View 1 Replies
View Related
Apr 24, 2012
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies
View Related
Dec 15, 2011
I have tryed to setup Lan connection on 2 PC to share wireless conenction from one to other PC.I have setup a few things but 2 PC cant see each other in workgroup(they have same name of WG).....soo i have try almost everything but didnt fix it
First PC(Host):Win XP PRO SP3
Second:Win XP PRO SP3
View 11 Replies
View Related
Oct 15, 2012
How do i add a computer to a workgroup?
View 1 Replies
View Related
Jun 9, 2011
I cannot join domain it saying that "Computer name changes", A domain controller for the domain MyDomain could not be contacted.”. We have domain and workgroup, Actually first its already joined the domain, but I want to map the sharedrive inside the workgroup but I cannot map. Then I change to join workgroup. After I boot up I cannot log in with that user, I log in with administrator and the user is dissappear in the "User Account", but the profile inside document and setting still left surprise. I don't know why Now I create one more user, it can map to share drive also share folder. also can see all other network computer. But only left one is I cannot join the domain. I need this one because of we don't let our user using as administrator account. Before I testing this one I should backup, but now the time
View 2 Replies
View Related
Mar 18, 2011
I have a desktop PC running WinXP I recently got a laptop running Win7. I Set both of them up with the same workgroup name, and now my XP machine can see and access my laptop, but my lap can't see my XP machine. If it makes any difference, I can remote into my XP from my laptop, but that's not what I need.
View 3 Replies
View Related
Feb 2, 2011
We have two different groups in network say 'A' and 'B'. My network is B. I can view the computers in my group simply by clicking "view workgroup computers". I wonder how I can view the computers in group 'A'
View 2 Replies
View Related
May 11, 2011
I have two computers, one that is running Windows XP SP3 and the other which is running Windows 7.My aim is to access a folder on the Windows 7 computer from the Windows XP computer via the workgroup.When on the Windows XP computer, I cannot view Workgroup computers.I have disabled Windows firewall & uninstalled my other firewall.The XP computer can ping the Win7 computer by name and local IP. However, the Win7 computer can only ping the XP computer by local IP and not computer name.
View 1 Replies
View Related
Aug 11, 2012
My computer was connected to a workgroup, we shared the same internet wireless connection, my printer is shared, but my officemate can't find my computer in their network places... I try all the ways given from the internet but nothings change... I'm been working for this for 2 days already
View 7 Replies
View Related
Jul 17, 2011
I have a few laptops at home and one desktop. I also have a work laptop which I carry to work every day. I have a lan at home. The computers are connected through a wireless router though my pc is connected through a lan cable. We are able to share files and content.
I sometimes connect my office laptop at home. Though the laptop connects to the network but I am unable to transfer or share files to other computers running Windows Vista/7. After a bit of research I figured this is because the workgroup name of my office laptop is different than the systems at home. I dont want to change the workgroup name of my office laptop as it will create problems at work.
How can I connected my office laptop to the network and transfer files if the workgroup name is different? It does show names of computers on network but when I try to connect a username & password box pops up.
View 6 Replies
View Related
Mar 25, 2011
When somebody opens my computer in workgroup it should ask user id and password.I mean if they type \mycomputer in run command, it should ask user id and password.
View 1 Replies
View Related
Sep 29, 2011
I have networked three computer using lan through wired switch. I have one net setter with me. And i have connected it with my one computer.And now how can i get internet on others computers.
View 1 Replies
View Related
Apr 30, 2013
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies
View Related
