Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 RepliesWe have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies View Relatedi got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies View RelatedI want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies View RelatedI config vlans 21-23 on 3750 A and B switches.I config B switch to be Root Bridge for all vlansspanning-tree vlan 1,21-23, priority 4096 sh span tree on B switch 3750B# sh spanning-tree.
View 18 Replies View RelatedI have two 6509s both with single FWSMs running in transparent mode with bridged Inside and Outside VLANs.I have my Core A set to STP priority of 8192 and Core B set to 16,384 to make Core A the root for all VLANs.Problem I have is when I look at spanning-tree on Core A for Inside VLAN 324 it states to get to the Root go via PO100 (Cost of 9) and that the Root also has a Priority of 8192, but as the designated Root has a lower MAC address it's pointing to the etherchannel. PO100 is L2 Etherchannel between the Cores.Moving accross PO100 to Core B and running the show spanning-tree command I can see that to get to the Root Bridge I need to go via PO272. PO272 is the internal Etherchannel to get to the FWSM on the Core B Switch. This shows a cost of 6 to get to the Root and a mac address of the Root Bridge which resides on Core A (Outside VLAN 124)To give some perspectibe,theoutside VLAN of the pair has it's STP ROOT on the Core A switch as intended?
View 1 Replies View RelatedI have an Extremely Old switch that I need to connect to my network. Because it is so old I don't want it to become the Root Switch.
what is the command to change the priority. (Honestly I don't remember if it has to be a lower number 1 or a higher number ). Always get that mixed up. I've read about root guard, but I would like to prevent it manually. (It is a small network after all)It is a Cisco 2950.
Any working configuration between two BR1310's in Root/Non-root mode? The documentation is vary vague and i can't find anything more secure than WEP. Is it possible to use WPA with radius authentication?
View 1 Replies View RelatedIs the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedI am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies View RelatedIs it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies View RelatedWe have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 Replies View RelatedI have some problem with 802.11A radio is enabled but the detaild status is still display software status is disabled and hardware status is down. I checked the settings on Enable Radio is checked on enable. I can't get any radio accross. whereelse I can check to get this working?
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
power local 18 <<<<<<<<<<< I can't input this line from the command line. I assume that the bridge is taking the MAX setting.
power client 18
packet retries 128
station-role non-root
rts threshold 4000
rts retries 128
concatenation
beacon period 20
infrastructure-client
In bridged network environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and source route learning is turned off. We had both on in the past. One side of the network has a link out to the internet. About 3 -4 times a day the IP address on the default gateway becomes unreachable i.e cant be pinged. Only a reboot of one or other of the bridges corrects the issue. This happens only during the day when the netwrok is in use. When this happens everything inside the network works fine and everybody can see everybody else. The ISP can see intot eh network and can ping our devices but we cannot see out of the network.
View 0 Replies View RelatedWe have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
View 1 Replies View RelatedI have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies View RelatedThe RG-59 coax cables that come with the 1310 bridge are only 1 foot long. where I could get longer cables as the power injector is quite a distance away because there are no close power sockets. Instead of installing new power sockets near to the bridge, we wanted to simply run longer coax cables.
View 3 Replies View RelatedI have requirement to enable the AES encryption on the management VLAN traffic between connected root and non root bridges .below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces?
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
Can we make a bridge connection between cisco aironet 1400 series and cisco R5005? In Root and Non Root Manner.
View 1 Replies View RelatedWe are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
can we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
I have cisco 1310 bridge with IOS version Version 12.3(7)JA5. Sometimes bridges are disconnecting by showing the following error message.
*Mar 1 01:22:21.856: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 003a.99eb.cc00 Reason: Previous authentication no longer valid
*Mar 1 01:22:22.115: %DOT11-4-MAXRETRIES: Packet to client 003a.99eb.cc00 reached max retries, removing the client
[Code]....
Once it is deassossiated, ihave to manually restart the bridges. How can avoid manual restarting so it would automatically associate after some time.
we have a 1310 connecting two buildings networks.inside each building we have a wireless network (Intermec access points).we are implementing WEP on the Intermec AP's.will the cisco 1310 allow the wep traffic without interference? or would i need to modify the 1310 somehow?
View 2 Replies View RelatedWhat is replacing the 1310 AP's in order to create a wireless bridge between sites?
View 3 Replies View RelatedI'm setting up a Wireless Bridge 1310 with two APs. The Root Bridge is working fine, but the Non-root Bridge is not working, the radio 0 is not UP (It is in reset mode), bellow the settings of APs and logs Non-root Bridge.
AP Root Bridge
dot11 ssid BRIDGE-INTERSITE
authentication open
[Code].....
I am trying to configure repeater mode on an AP, but the authentication is not working.It seems the authentication is seen as EAP-TLS on the ACS 5.2, but im trying to do LEAP.
Relevant config root AP:
!
dot11 ssid Auto3
authentication open eap eap_methods
authentication network-eap eap_methods1
guest-mode
infrastructure-ssid
[code].....
how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View Relatedif the Cisco 3502p AP can run as a root mesh access point ?
View 4 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Another query regarding diagnostic test and Test DNS Root. It always fails why?
We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?