Cisco Wireless :: 1310 EOL - Create A Wireless Bridge Between Sites?

Nov 15, 2012

What is replacing the 1310 AP's in order to create a wireless bridge between sites?

View 3 Replies


ADVERTISEMENT

Cisco Wireless :: Using VLANs With 1310 Bridge

Dec 18, 2012

I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]

View 4 Replies View Related

Cisco Wireless :: 1242 And 1310 Bridge?

Apr 18, 2011

Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.

View 2 Replies View Related

Cisco Wireless :: 1310 Bridge Default Gateway

Jan 11, 2012

In  bridged network environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and source route learning is turned off. We had both on in the past. One side of the network has a link out to the internet. About 3 -4 times a day the IP address on the default gateway becomes unreachable i.e cant be pinged. Only a reboot of one or other of the bridges corrects the issue. This happens only during the day when the netwrok is in use. When this happens everything inside the network works fine and everybody can see everybody else. The ISP can see intot eh network and can ping our devices but we cannot see out of the network.

View 0 Replies View Related

Cisco Wireless :: Power Injector For 1310 Bridge

Apr 11, 2013

We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?

View 1 Replies View Related

Cisco Wireless :: 1310 / Unable To Ping Across Bridge?

Jun 17, 2012

I have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.  

View 1 Replies View Related

Cisco Wireless :: 1310 Bridge RG-59 Coax Cables?

May 8, 2007

The RG-59 coax cables that come with the 1310 bridge are only 1 foot long. where I could get longer cables as the power injector is quite a distance away because there are no close power sockets. Instead of installing new power sockets near to the bridge, we wanted to simply run longer coax cables.

View 3 Replies View Related

Cisco Wireless :: Enable AES Encryption On 1310 WLAN Bridge?

Sep 19, 2012

I have requirement to enable the AES encryption on the management VLAN  traffic  between connected root and non root bridges .below is the network setup  .
  
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
 
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces?

View 1 Replies View Related

Cisco Wireless :: Aironet 1310 Bridge - Cannot Access GUI To Configure

Nov 21, 2011

I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
 
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.

View 3 Replies View Related

Cisco Wireless :: Setting Up A Wireless Bridge 1310 With Two APs?

May 8, 2012

I'm setting up a Wireless Bridge 1310 with two APs. The Root Bridge is working fine, but the Non-root Bridge is not working, the radio 0 is not UP (It is in reset mode), bellow the settings of APs and logs Non-root Bridge.
 
AP Root Bridge
dot11 ssid BRIDGE-INTERSITE
authentication open

[Code].....

View 3 Replies View Related

Cisco Wireless :: Aironet 1310 Bridge High Retries One Direction

Aug 15, 2011

We are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas.  What would this indicate?  Here is a copy of the linktest:
 
POOR (102% retries)  Time   Strength(dBm)   SNR      SNR          Retries
msec      In     Out    In      Out         In   Out
Sent :5000, Avg   5    - 66    - 64    31       45   Tot:  56  10149

[Code]....

View 2 Replies View Related

Cisco Wireless :: Associate Non-root Bridge Model 1310 To Root Bridge Model 1400?

Apr 24, 2012

Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?

View 7 Replies View Related

Cisco Wireless :: 1310 Point-to-point Bridge In Lightweight Mode?

Apr 24, 2011

how is the 1130 point-to-point bridge work in lighteight mode ?
 
Is this supported on 5508 and on new 2500 series controllers?
 
How does the WCS manage the point-to-point link?
 
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far

View 6 Replies View Related

Cisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)

Apr 24, 2011

Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)

View 3 Replies View Related

D-Link DI-524 - Create A Wireless Bridge?

Jun 19, 2011

my wireless router that is connected to the internet is in the basement and my computer is upstairs on the second floor of my house. Because of this the signal is very bad, to fix this problem I bought a Belkin Wireless N300 in order to create a wireless bridge but I am having trouble. My downstairs router is a D-Link DI-524 and I have googled all over the place to find a solution but the belkin router doesn't have a wireless bridging option...

View 2 Replies View Related

Linksys WAG54gs - Create A Wireless Bridge?

Feb 20, 2013

I am wondering if it is possible to Create a wireless bridge. I am trying to connect a linksys WAG54gs to next doors wireless router. It's ok she's my mother in law.
She has a BT home hub 3.

View 1 Replies View Related

How To Create Bridge To RNX-N100 USB Wireless Dongle

Feb 21, 2011

I use the DWA-552 Linksys wireless card on my PC. I would like to create either a bridge (which seems complicated) to my RNX-N100 USB Wireless dongle. The reason being, I am going to use the RNX to get access to the internet for my Blu-Ray player (BD-C5500T). I have looked everywhere and cannot find any info on the setup. The other way is to connect the PC to my T.V. as my integrated card has an HDMI port and bridge the wireless connection with the integrated wired connection (if that is possible) so i can gain internet access to my Blu-Ray player. I have tried to configure with my player and no-go. It works fine when i configure the RNX on my PC though.

View 8 Replies View Related

Cisco Wireless :: Use 1242 5GHz To Create Wi-Fi Bridge?

Oct 15, 2012

I have Eight AIR-AP1242AG-E-K9's accross our site that have 2 SSID's and 2 VLAN's that work well, I want to link one of the AIR-AP1242AG-E-K9 to another one using 5ghz patch antennas across a 50 metre gap, but I am puzzled on how to do this, as to create a root bridge and a non route bridge link I need to put the infrastucture SSID on and this must be on VLAN1  but I want the traffic from both VLANs to pass over this link. I just want to ensure the config will work as I need to go into a cherry picker to get to the non-root-bridge.

View 11 Replies View Related

Linksys Wireless Adapters :: WUSB600N - Can't Create Network Bridge In Windows Xp

Jun 29, 2012

I can't create a network bridge in windows xp or well i can, but then my wusb600n says it is not connected, it can find networks but it wont connect to them? I tried take out the lan cable and create but with same result, is this normal that this adapter can't handle network bridge? If i make a virtual machine in Virtualbox i can use the internet, but i cant when i create a network bridge connection in windows xp..

View 5 Replies View Related

Cisco :: Connection Loss Of 1310 Bridge?

May 20, 2012

I have cisco 1310  bridge  with IOS version  Version 12.3(7)JA5. Sometimes bridges are disconnecting by showing the following error message.

*Mar 1 01:22:21.856: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 003a.99eb.cc00 Reason: Previous authentication no longer valid
*Mar 1 01:22:22.115: %DOT11-4-MAXRETRIES: Packet to client 003a.99eb.cc00 reached max retries, removing the client

[Code]....

Once it is deassossiated, ihave to manually restart the bridges. How can avoid manual restarting so it would automatically associate after some time.

View 14 Replies View Related

Cisco :: 1310 Bridge - Transparent To Local WEP Traffic?

Aug 10, 2011

we have a 1310 connecting two buildings networks.inside each building we have a wireless network (Intermec access points).we are implementing WEP on the Intermec AP's.will the cisco 1310 allow the wep traffic without interference? or would i need to modify the 1310 somehow?

View 2 Replies View Related

Cisco VPN :: VPN 3000 Setting Two Concentrators At Different Sites To Create Ipsec Tunnel

May 20, 2011

I'm currently setting up two VPN 3000 Concentrators at two different sites to create a IPsec LAN-to-LAN Tunnel. I have gone through all the basic configuration guides on the CISCO site, but a LAN-to-LAN session is never created. I have enabled the logs on the Concentrator and it displays no errors at all - it appears the Concentrator is not even trying to establish a IPsec LAN-to-LAN Tunnel.After running through the standard setup provided by CISCO, is there anything I need to do to make the Concentrator try to create a Tunnel, or should this be automatic once all settings are in place?

View 2 Replies View Related

Cisco Wireless :: AP 1310 Not Able To Join Controller

May 20, 2013

i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
 
here is the output of debug command
  
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table

[Code].....

View 3 Replies View Related

Cisco Wireless :: 1310 / Manually Configuring The LAP?

Apr 15, 2012

I have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.

View 5 Replies View Related

Cisco Wireless :: 1310 Ap WPA2 Configuration

Jul 26, 2011

I am looking for an example configuration of a Cisco 1310 running 123-7.JA2 Z Ios, for Wpa2 using an external Cisco acs radius server.

View 3 Replies View Related

Cisco Wireless :: 1310 Autonomous To LAP Conversion

Oct 22, 2012

Customer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
 
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
  
is this action free of charge ? Nedd I SMARTENT COVERAGE ?

View 3 Replies View Related

Cisco Wireless :: Cannot Access GUI - Aironet 1310

Apr 29, 2013

I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions).  I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.   

View 1 Replies View Related

Cisco Wireless :: IOS Image For Aironet 1310?

Apr 5, 2012

Any IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.

- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar

View 2 Replies View Related

Cisco Wireless :: Convert Aironet 1310 Autonomous To LAP?

Apr 22, 2012

Is it possible to also upgrade the 1310 series cisco ap's from  autonomous to lwap without using the upgrade tool, if so what procedure  do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy

View 1 Replies View Related

Cisco Wireless :: 1310 Bridges Keep Losing Connection?

Nov 28, 2010

I have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection.  When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
 
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
 
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)

View 12 Replies View Related

Cisco Wireless :: 1310 LAP Unable To Join WLC 5508?

Jan 10, 2013

I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
 
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar  1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface

[Code].....

View 11 Replies View Related

Cisco Wireless :: Can The Aironet 1310 Setup As A Repeater

Jul 10, 2012

Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.

View 11 Replies View Related

Cisco Wireless :: 1310 LAP Is Not Joining To 5508 Wlan Controller V7.4?

Mar 15, 2013

I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller.  What to do?  How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved