Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 RepliesCustomer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
is this action free of charge ? Nedd I SMARTENT COVERAGE ?
configuration of a 1310 that will be a root access point and connected to wlc 4402. The AP will be implemented as autonomous and not lightweight.
View 3 Replies View RelatedHow do I change 1310 Autonomous AP to a Controller based AP for 5508 WLC?
View 6 Replies View RelatedI have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies View Relatedhow to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies View Relatedi have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
I have an AP 1141N-A-K9, from autonomous system, with this IOS ( c1140-k9w7-mx.124-21a.JA1), and a WLC 5508 with Version 7.X
I want to convert this AP to lightway to use with this controller.
I download de Version of IOS (c1140-rcvk9w8-tar.124-21a.JA2.tar) from cisco and the upgrade tool. but when I start the process in the upgrade tool the result is "this version is not supported by the upgrade tool", it pass all the requested information but show this error at the end.
Is it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies View RelatedApparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies View Relatedsome days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View RelatedIs it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedI have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies View RelatedI've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies View RelatedAny IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies View RelatedI migrate 1310 APs from Autonomous to Lightweight. Migration is OK with Cisco Upgrade Tool, and AP are registered on my 2504 WLC.
Previously, a 802.1x network was broadcasted by autonomous APs, supplicants were identified on a freeradius server with MSCHAPv2/PEAP method.
But on the WLC, supplicants can't auth on Radius server.I configured a WLAN with WPA/TKIP/802.1x with my radius server in AAA tab.When clients try to authenticate, I get these messages where xxx is login:
-AAA Authentication Failure for UserName:821 User Type: WLAN USER
-AAA Authentication Failure for UserName:200 User Type: WLAN USER
-AAA Authentication Failure for UserName:209 User Type: WLAN USER
Security info on client page is:
Security Policy CompletedNo ###Policy TypeWPA###Encryption CipherTKIP-MIC###EAP TypePEAPSNMP NAC State Access ###Radius NAC State8021X_REQD .
What is strange, there are some clients which are OK in RUN State, and 50 other % which are not.
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies View RelatedI got 4 aironet 1310 Πbut i don't have password into Enable mode!. I follow this document "Password Recovery Procedure for the Cisco Aironet Equipment.pdf" to recovery password. It succeed reset password to default Πbut it also reset Previous setting to default.
Can I reset aironet 1310 password and keep Previous setting?
We are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
I would like to know is it possible to convert a Cisco Aironet AIR-AP1042N-x-K9 to LAP ?
View 3 Replies View RelatedI want to convert LAP AIR-AP1121G-E-K9 to autonomous AP.
View 1 Replies View RelatedWe have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies View Relatedi'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies View RelatedI need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies View Relatedupgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedI purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View RelatedWe have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....