Cisco Wireless :: Change 1310 Autonomous AP To Controller Based?
Apr 6, 2013How do I change 1310 Autonomous AP to a Controller based AP for 5508 WLC?
View 6 Replies
ADVERTISEMENT
Cisco Wireless :: Difference Between Controller Based And Autonomous AP 150 Design
May 20, 2013I have to make a design for 150 sites, the large sites (40) will be controller based designs.But for the small sites (110) contains 3 APs, which will not have a controller onsite. (or should it be ??)Besides the overall management , which features do I miss if it is controller based or standalone APs.Like CleanAir , etc.
View 2 Replies View RelatedCisco Wireless :: 1310 Autonomous To LAP Conversion
Oct 22, 2012Customer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
is this action free of charge ? Nedd I SMARTENT COVERAGE ?
Cisco Wireless :: Convert Aironet 1310 Autonomous To LAP?
Apr 22, 2012Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies View RelatedCisco Wireless :: Connecting 1310 AP To WLC 4402 In Autonomous Mode?
Mar 16, 2013configuration of a 1310 that will be a root access point and connected to wlc 4402. The AP will be implemented as autonomous and not lightweight.
View 3 Replies View RelatedCisco :: 1310 - 802.1x Authentication Fail Through WLC But OK On Autonomous APs
Jun 5, 2013I migrate 1310 APs from Autonomous to Lightweight. Migration is OK with Cisco Upgrade Tool, and AP are registered on my 2504 WLC.
Previously, a 802.1x network was broadcasted by autonomous APs, supplicants were identified on a freeradius server with MSCHAPv2/PEAP method.
But on the WLC, supplicants can't auth on Radius server.I configured a WLAN with WPA/TKIP/802.1x with my radius server in AAA tab.When clients try to authenticate, I get these messages where xxx is login:
-AAA Authentication Failure for UserName:821 User Type: WLAN USER
-AAA Authentication Failure for UserName:200 User Type: WLAN USER
-AAA Authentication Failure for UserName:209 User Type: WLAN USER
Security info on client page is:
Security Policy CompletedNo ###Policy TypeWPA###Encryption CipherTKIP-MIC###EAP TypePEAPSNMP NAC State Access ###Radius NAC State8021X_REQD .
What is strange, there are some clients which are OK in RUN State, and 50 other % which are not.
Cisco :: Adding 1310 Autonomous AP To WCS Before Upgrade To Lightweight
Jan 30, 2011I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies View RelatedCisco Wireless :: 5500 / Controller Versus Cloud-based (Controller)
Mar 31, 2013We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies View RelatedCisco Wireless :: AP 1310 Not Able To Join Controller
May 20, 2013i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
Cisco Wireless :: 1310 LAP Is Not Joining To 5508 Wlan Controller V7.4?
Mar 15, 2013I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedCisco Wireless :: Combining 1310 Bridges With 5508 Controller
Jul 10, 2012I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View RelatedCisco Wireless :: Change IOS Of 1252 LWAP AP To Autonomous AP?
Jun 20, 2011Is it possible to Change IOS of 1252 LWAP AP to Autonomous AP? I have seen some documents for changing Autonomous AP to LWAP and change back procedures.
View 4 Replies View RelatedCisco Wireless :: Aironet 3602I-K9 - How To Change To Autonomous AP
Mar 25, 2013I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
Cisco Wireless :: 1131 Light Weight AP To Autonomous Conversion Without Controller
Jan 15, 2013I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .
View 1 Replies View RelatedCisco Wireless :: Aironet 1250 AIR-LAP1252AG-A-K9 - Change To Autonomous Mode
Jun 11, 2013I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
Cisco Wireless :: 1552 - Controller Based Mesh Configuration
Jun 26, 2012I have to install a wireless mesh network shortly using Cisco 1552 APs. This will be controller based using 5508 controllers. The controllers currently have some 1262 APs configured in a mesh and bridging configuration so happy that it all basically works. My question is - what is the "config mesh range' command doing on the controller ( or setting the Range(RootAP to MeshAP) setting on the controller mesh GUI. The default setting is 12000feet and I have left it at default at present. Just interested in what this is used for - I assume it alters the mesh protocol parameters somehow ( or the RF parameters perhaps ) as it suggests in the guide that mesh APs will reboot following this command being changed.
View 4 Replies View RelatedCisco Wireless :: AIR-AP1231G-A-K9 And Controller Based Environment With Prime NCS
Apr 15, 2012I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View RelatedCisco Wireless :: Laptop Is Not Connecting With 2504 Controller Based 1131AG Access?
Jul 12, 2012I have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies View RelatedLinksys Wireless Router :: How To Change Language Of WRT54GL's Web-based Utility
Jan 16, 2008I'm just finished with the wizard of my WRT54GL and follow the instructions in my user's manual I enter in the Web-based Utility of the router but I was surprised when I see that the language is French?! Once I choose the language for the wizard - english, it was english but now the Web-based Utility is in French. For luck I know some French from the high school but I prefer to work with English. How to change the language of the Web-based Utility from French to English
View 9 Replies View RelatedCisco Wireless :: 5500 Controller - Change IP Of WCS Server?
Aug 27, 2011I have two 5500-controllers and one WCS-server. Now I will have to move the WCS-server to another subnet and change the IP, but it will keep the name.Will that effect the connection between the controllers and the WCS?Do I have the change anything in the configuration on the controllers or the WCS-server?
View 3 Replies View RelatedHow To Change IP To Get Vote On IP Based Contest
Jun 1, 2012I have a photo contest, but its seem it using IP based system.So that after done giving vote there, I can't give ore vote there.I wonder, because there's many contestant get till 2000 votes at the same contest and look so easy to collect it.[CODE]
View 1 Replies View RelatedCisco :: WCS 7.0.164.3 - Change Controller IP-address?
Jan 19, 2011We have a WCS 7.0.164.3 with 27 WLCs. We are now running a project where were creating new subnets on our locations - and because of this we have to change the controllers management ip-adresses.
I am able to change the ip-address of the management interface both through wcs and on the wlc, but the controllers ip-address (the one we see under Configure - controllers) is still the old one. This causes the wcs to loose connection to the wlc. I have to delete the controller, and then add it with the new IP. The APs are then removed from the maps, and I have to manually place them on the maps again - this is a lot of work with 700 APs.
Is there a way to change the controller IP in WCS?
Dell :: After Change OS To Windows 7 Pro Enterprise E5430 Missing Network Controller Driver
Jun 11, 2013After change my OS to Windows 7 Pro Enterprise my Dell E5430 missing the network controller driver. let me know the right driver to download and install.
View 4 Replies View RelatedCisco Wireless :: Using VLANs With 1310 Bridge
Dec 18, 2012I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies View RelatedCisco Wireless :: 1242 And 1310 Bridge?
Apr 18, 2011Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies View RelatedCisco Wireless :: 1310 / Manually Configuring The LAP?
Apr 15, 2012I have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies View RelatedCisco Wireless :: 1310 Ap WPA2 Configuration
Jul 26, 2011I am looking for an example configuration of a Cisco 1310 running 123-7.JA2 Z Ios, for Wpa2 using an external Cisco acs radius server.
View 3 Replies View RelatedCisco Wireless :: Cannot Access GUI - Aironet 1310
Apr 29, 2013I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies View RelatedCisco Wireless :: IOS Image For Aironet 1310?
Apr 5, 2012Any IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
Cisco Wireless :: 4404 Guest Anchor Controller With 5508 Foreign Controller?
Aug 12, 2012I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedCisco Wireless :: 5508 Foreign Controller And 4400 Anchor Controller?
Jun 2, 2013We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedCisco Switching/Routing :: 2125 Wireless Controller Without Anchor Controller Just Using Existing Hardware
Dec 6, 2012I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
Cisco Wireless :: 1310 Bridge Default Gateway
Jan 11, 2012In bridged network environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and source route learning is turned off. We had both on in the past. One side of the network has a link out to the internet. About 3 -4 times a day the IP address on the default gateway becomes unreachable i.e cant be pinged. Only a reboot of one or other of the bridges corrects the issue. This happens only during the day when the netwrok is in use. When this happens everything inside the network works fine and everybody can see everybody else. The ISP can see intot eh network and can ping our devices but we cannot see out of the network.
View 0 Replies View Related