I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies
We have a pair of 1310's (running 12.3(8)JEA3) connecting 2 buildings together. The wired side of each AP is connected to switchports configured as access ports.
But, now we need to extend multiple VLANs across the wireless bridge. So I'm thinking I just need to configure some sub-interfaces on the radio side and ethernet side and bridge them together. But I'm unclear on if I need an SSID for each bridge group. I would hope not. But after reading this, I'm not sure. Most of the documentation seems to be dealing with wireless clients. Well, in this case I don't have any wireless clients and just need to extend VLANs.
These 2 sites are hundreds of miles away from where I am, and I don't have any 1310's to test this out on. Should I be able to load similar software on other AP's (like 1142's) and have them function as bridges to test this out?
Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies View RelatedIn bridged network environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and source route learning is turned off. We had both on in the past. One side of the network has a link out to the internet. About 3 -4 times a day the IP address on the default gateway becomes unreachable i.e cant be pinged. Only a reboot of one or other of the bridges corrects the issue. This happens only during the day when the netwrok is in use. When this happens everything inside the network works fine and everybody can see everybody else. The ISP can see intot eh network and can ping our devices but we cannot see out of the network.
View 0 Replies View RelatedWe have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
View 1 Replies View RelatedI have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies View RelatedThe RG-59 coax cables that come with the 1310 bridge are only 1 foot long. where I could get longer cables as the power injector is quite a distance away because there are no close power sockets. Instead of installing new power sockets near to the bridge, we wanted to simply run longer coax cables.
View 3 Replies View RelatedI have requirement to enable the AES encryption on the management VLAN traffic between connected root and non root bridges .below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces?
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedWe are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
What is replacing the 1310 AP's in order to create a wireless bridge between sites?
View 3 Replies View RelatedI'm setting up a Wireless Bridge 1310 with two APs. The Root Bridge is working fine, but the Non-root Bridge is not working, the radio 0 is not UP (It is in reset mode), bellow the settings of APs and logs Non-root Bridge.
AP Root Bridge
dot11 ssid BRIDGE-INTERSITE
authentication open
[Code].....
I have cisco 1310 bridge with IOS version Version 12.3(7)JA5. Sometimes bridges are disconnecting by showing the following error message.
*Mar 1 01:22:21.856: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 003a.99eb.cc00 Reason: Previous authentication no longer valid
*Mar 1 01:22:22.115: %DOT11-4-MAXRETRIES: Packet to client 003a.99eb.cc00 reached max retries, removing the client
[Code]....
Once it is deassossiated, ihave to manually restart the bridges. How can avoid manual restarting so it would automatically associate after some time.
we have a 1310 connecting two buildings networks.inside each building we have a wireless network (Intermec access points).we are implementing WEP on the Intermec AP's.will the cisco 1310 allow the wep traffic without interference? or would i need to modify the 1310 somehow?
View 2 Replies View Relatedhow is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View Relatedif I want to bridge between 2 VLANs ,can I use IRB like I would use in a router for bridging to ethernet interfaces for example?
Config example:
bridge irb
interface vlan 10
ip address 192.168.10.1 255.255.255.0
bridge-group 1
[code].....
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
I have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies View RelatedI am looking for an example configuration of a Cisco 1310 running 123-7.JA2 Z Ios, for Wpa2 using an external Cisco acs radius server.
View 3 Replies View RelatedCustomer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
is this action free of charge ? Nedd I SMARTENT COVERAGE ?
I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies View RelatedAny IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies View RelatedI have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection. When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies View RelatedI have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedI have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View Relatedconfiguration of a 1310 that will be a root access point and connected to wlc 4402. The AP will be implemented as autonomous and not lightweight.
View 3 Replies View RelatedHow do I change 1310 Autonomous AP to a Controller based AP for 5508 WLC?
View 6 Replies View RelatedI have a Problem with a customer WLAN. The customer has a Aeronet 1130AG AP. Now i should configure a Aironet 1130 Repater for this WLAN. The initial connection from the Repater with the AP is no Problem. But after some time the Repeater lost the connection. On the AP i see following Messages:20Jul 19 19:05:28.061InformationInterface Dot11Radio0, Deauthenticating Station xxx Reason: Previous authentication no longer valid 21Jul 19 19:05:28.061WarningPacket to client xxx reached max retries, removing the client 22Jul 19 16:43:59.412InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx23Jul 19 16:43:57.901InformationInterface Dot11Radio0, Deauthenticating Station yyy 24Jul 19 16:43:56.536InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx 25Jul 19 16:43:51.555InformationInterface Dot11Radio0, Station zzz Associated KEY_MGMT[WPA PSK] 26Jul 19 16:43:29.078InformationInterface Dot11Radio0, Station Repeater01 xxx Associated KEY_MGMT[WPA PSK]
View 2 Replies View Related
