We are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies View RelatedAny IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies View RelatedCan the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies View RelatedI am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies View RelatedIs it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies View RelatedI got 4 aironet 1310 Πbut i don't have password into Enable mode!. I follow this document "Password Recovery Procedure for the Cisco Aironet Equipment.pdf" to recovery password. It succeed reset password to default Πbut it also reset Previous setting to default.
Can I reset aironet 1310 password and keep Previous setting?
In bridged network environment. We have a pair of Cisco 1310 bridges configued betweeen 2 buildings the config on each is simple one as a root bridge the other as non root no spanning tree is running and source route learning is turned off. We had both on in the past. One side of the network has a link out to the internet. About 3 -4 times a day the IP address on the default gateway becomes unreachable i.e cant be pinged. Only a reboot of one or other of the bridges corrects the issue. This happens only during the day when the netwrok is in use. When this happens everything inside the network works fine and everybody can see everybody else. The ISP can see intot eh network and can ping our devices but we cannot see out of the network.
View 0 Replies View RelatedWe have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
View 1 Replies View RelatedI have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies View RelatedThe RG-59 coax cables that come with the 1310 bridge are only 1 foot long. where I could get longer cables as the power injector is quite a distance away because there are no close power sockets. Instead of installing new power sockets near to the bridge, we wanted to simply run longer coax cables.
View 3 Replies View RelatedWe have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies View RelatedI have requirement to enable the AES encryption on the management VLAN traffic between connected root and non root bridges .below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces?
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedWhat is replacing the 1310 AP's in order to create a wireless bridge between sites?
View 3 Replies View RelatedI have configured a Aironet 1310 bridge as a WGB and is connected to a Aironet 1242AG AP wirelessly!A sensor(IP device) is wired into the 1310WGB. The sensor needs MULTICAST to operate!I checked the DETAILED STATUS of the RADIO and both the 1310 and 1242 are blocking multicast!The RELIABLE MULTICAST TO WGB option is enabled on the 1242AP already!
View 1 Replies View RelatedI'm setting up a Wireless Bridge 1310 with two APs. The Root Bridge is working fine, but the Non-root Bridge is not working, the radio 0 is not UP (It is in reset mode), bellow the settings of APs and logs Non-root Bridge.
AP Root Bridge
dot11 ssid BRIDGE-INTERSITE
authentication open
[Code].....
I have cisco 1310 bridge with IOS version Version 12.3(7)JA5. Sometimes bridges are disconnecting by showing the following error message.
*Mar 1 01:22:21.856: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 003a.99eb.cc00 Reason: Previous authentication no longer valid
*Mar 1 01:22:22.115: %DOT11-4-MAXRETRIES: Packet to client 003a.99eb.cc00 reached max retries, removing the client
[Code]....
Once it is deassossiated, ihave to manually restart the bridges. How can avoid manual restarting so it would automatically associate after some time.
we have a 1310 connecting two buildings networks.inside each building we have a wireless network (Intermec access points).we are implementing WEP on the Intermec AP's.will the cisco 1310 allow the wep traffic without interference? or would i need to modify the 1310 somehow?
View 2 Replies View Relatedhow is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedI have two Cisco Aironet 1252 that I want to configure as a point-2-point bridge. Now I want to know if this configuration supports the 802.11n protocol.
View 2 Replies View RelatedI work for a small college. We have several Cisco 1200 Aironet deployed our the campus, all of which are configures to run multiple SSID's. The problem I have is that when I connect, via AP, it successfully connects to the desired SSID but on pinging the default gateway of said SSID I get high latency (avg around 100 - 200ms).When pinging from the switch (Cisco 2950) to the default gateway the latency is good (1-2ms). It is just high when I connect via the C1200 AP and try to ping.
View 1 Replies View RelatedIs the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedI've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies View RelatedI want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View Relatedreloads of aps joined to wlc 2504 7.3 with this log messages
*Dec 3 16:30:47.575: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: LSC Provision max retries.
*Dec 3 16:30:47.575: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
In the company we have two SSIDs for corporate and guest networks respectively when I try to connect to any of the SSIDs it doesn't happen until 5 retries. The only log I get that seems to be related to it is the following:
*Jun 11 11:48:09.062: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:23:32:73:d7:15 due to switch of WLANs from 1(femsawl) to 2(visitas)
Here it shows a switch between SSIDs but if you just turned on an apple device and try to associate for the first time to any of the SSIDs the scenario is the same, several tries to connect.I am running a 4402 wlc with 6.0.202.0 software version.
I have two 1410 bridges installed in a point to point link using external directional antennas. The distance between the bridges is only 200M. As you can see below from the output the RSSI and SNR are excellent with a good fade margin available. These stats are almost identical to what my path profile calculated out to be. During normal operation the latency on this link sub 2ms, during certain conditions the latency jumps to 40+ms and starts dropping packets. I say certain conditions because we have not been able to pinpoint it. Unfortunately at this time the customer does not have the ability to do any SNMP polling or collect any statistical information (working on getting this setup). There are an excessive number of data retries and am not sure if that is normal. During the issues I have observered the below command output and the numbers did not change, which leads to me believe that it is not a RF issue. It almost looks like it's serialization delay, but I have no data to back that up. During iperf performance testing of this wireless link I could push 54Mbps of UDP traffic no problem, no errors, no CRC's.
Bridge Parameters
Encryption: WPA-PSK w/TKIP
Distance parameter: Configured to 1
[Code].....