I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Repliesi need to configure wireless link between my 1300 series, how can i use them like a bridge and access point in the same time?
Do i need static ip for BVI interfacess between them for bridge or its need to be DHCP, is there any example?
Product/Model Number:AIR-BR1310G-A-K9
System Software Filename:c1310-k9w7-tar.123-7.JA
System Software Version:12.3(7)JA
Bootloader Version:12.3(2)JA4 .
We have several of these bridges hanging around; would like to move them one at a time from our 1030WLSE to our 5508WLC (software 7.0.235, so they're compatible).The bridges are all connected to power injectors (AIR-PWRINJ-BLR2). With our 1200's, we apparently just unplug power, hold mode button, plug in power, release mode after about 4 seconds, and they find the new controller (I haven't tried it yet to confirm, but that's what Google...err...Cisco...says will work!). But obviously there's no "mode" or reset button on either the power injector or the bridge itself.
(Other than "shut down the old controller and the bridges and APs will find the new controller". I'll do that at some point, but want to test first with some spare bridges / APs.)
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies View RelatedA customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies View RelatedWhat is the average/maximum distance coverable by Aironet 1300 and 1240AG ???
View 3 Replies View RelatedI have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies View RelatedLooking to put a wireless bridge in to connect 2 building about 2000 feet apart. Excellent Line Of Site from rooftop to rooftop. Very little data traffic but will be running Voice over the link. Any have any input on using the 1300 bridges for this application as a permanent install?
View 5 Replies View RelatedI have two Cisco Aironet 1252 that I want to configure as a point-2-point bridge. Now I want to know if this configuration supports the 802.11n protocol.
View 2 Replies View RelatedIs the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedI have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
We are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedI want to connect with wireless devices two buildings, one in front of another. Short distance (about 20 meters) and no obstacles. I have a couple of aironet 1242 and i was wondering if it would be possible to setup this link with this equipment.
could WGB be the solution?
I have some problem with 802.11A radio is enabled but the detaild status is still display software status is disabled and hardware status is down. I checked the settings on Enable Radio is checked on enable. I can't get any radio accross. whereelse I can check to get this working?
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
power local 18 <<<<<<<<<<< I can't input this line from the command line. I assume that the bridge is taking the MAX setting.
power client 18
packet retries 128
station-role non-root
rts threshold 4000
rts retries 128
concatenation
beacon period 20
infrastructure-client
Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
View 16 Replies View RelatedCan we make a bridge connection between cisco aironet 1400 series and cisco R5005? In Root and Non Root Manner.
View 1 Replies View Relatedcan we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
i am able to connect to unsecured wireless networks but when i connect alll of them say no internet access i only notice a yellow warning sign beside those signal strength bars also and not on secured one !
View 2 Replies View RelatedI have a Dell Inspiron 1720, that uses a 1300 wireless lan, that keeps crashing. Is there a fix for this, can I replace it with another wireless lan card? Whenever I first start the computer, I would get the error message saying your wireless card had stopped working.
View 4 Replies View RelatedI have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies View RelatedI have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies View RelatedMy wife has a Dell Inspiron 1300 which crashed. I was able to start it again using the Dell Operating System Reinstallation CD for XP Professional but the wifi (wireless) does not work. Before the crash it had a working wireless connection. It appears that I need to reinstall a driver for it. How can I get a driver when I have no internet connection on that computer? I have tried loading on a flash driver from another computer, but it doesn't seem to transfer. What driver do I need and how can I get it to install on her computer?
View 5 Replies View RelatedSince we upgrade WLC in version 7.0.230 my PC with atheros card (version client 8.0.140 and driver 9.2.0.419) have brief interruption. In System events we have a lot of events ID 4201 and 1007. I try use Windows Wireless Client and we have not problem but the roaming is not fast. I don't find other client Utility for Atheros.
View 2 Replies View RelatedIs it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies View RelatedI have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this event,and hence will not renew its IP address until lease expiers. This is not a problem of course when Layer 2 roam occurs, but with Layer 3
roam it will interrupt the traffic.
The cisco's IP Mobile implementation does have this issue addressed in DCCoA scenario: the WGB is configured to send an SNMP trap on its dotradio state change;the cisco mobile router is configured with snmp-server manager to process this trap and start DHCP renew on the Down/Up event. Unfortunately, this works in Mobile IP scenario only because I cannot make it work without the mobile router registered with a home agent.
how to force DHCP renew on a client (cisco IOS router) in such a situation - event scripting, SLA, or ...?
My lap top and pc were both accessing internet fine. Now my laptop has the message windows cannot config. wireless connection. If you have enabled another prog. to manage this connection use that software. Then it says ifI want windows to config., start WZC service. I am a novice and don't understand any of this. I don't think I have done anything to enable another prog to manage the connection. I have tried reloading isp disc and making new network connection but to no avail. the little network logo has a red x constantly.
View 4 Replies View Relatedused to use Ethernet connection on this pc for 2/3 years, i recently ran wireless for like 2months. every time i try and use Ethernet i get limited or no connectivity warning, I looked in my ipconfig, i notice theres no physical address or default gateway for my realtek rtl8139/810x family fast Ethernet.
View 4 Replies View RelatedI'm running web server on Linux Redhat when i run
# /etc/init.d/tomcat status
I got a number of lines:
warning, got duplicate tcp line
warning, got duplicate tcp line
warning, got duplicate tcp line
warning, got duplicate tcp line
Tomcat running in normal mode Also , I can see that Tomcat unstability makes some strange behaviour in the system overall.
I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedWhat does this message mean? Jan 24 11:17:45 DIR-655 user.warn kernel: [175630.020000] Inteference detected.
View 4 Replies View RelatedI'm configuring the nat on a ASA5525 running on 9.1.2 and got 2 questions, 1. Is the below overlap warning message normal and will not cause any issue? 2. Is there a simple way on 8.3 and later to fulfill the same functionality like 8.2 and earlier?
old config on 8.2 and earlier
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
nat (dmz) 1 0.0.0.0 0.0.0.0 0 0
global (outside) 1 216.19.84.5
[code]....