i need to configure wireless link between my 1300 series, how can i use them like a bridge and access point in the same time?
Do i need static ip for BVI interfacess between them for bridge or its need to be DHCP, is there any example?
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies View RelatedProduct/Model Number:AIR-BR1310G-A-K9
System Software Filename:c1310-k9w7-tar.123-7.JA
System Software Version:12.3(7)JA
Bootloader Version:12.3(2)JA4 .
We have several of these bridges hanging around; would like to move them one at a time from our 1030WLSE to our 5508WLC (software 7.0.235, so they're compatible).The bridges are all connected to power injectors (AIR-PWRINJ-BLR2). With our 1200's, we apparently just unplug power, hold mode button, plug in power, release mode after about 4 seconds, and they find the new controller (I haven't tried it yet to confirm, but that's what Google...err...Cisco...says will work!). But obviously there's no "mode" or reset button on either the power injector or the bridge itself.
(Other than "shut down the old controller and the bridges and APs will find the new controller". I'll do that at some point, but want to test first with some spare bridges / APs.)
I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies View RelatedLooking to put a wireless bridge in to connect 2 building about 2000 feet apart. Excellent Line Of Site from rooftop to rooftop. Very little data traffic but will be running Voice over the link. Any have any input on using the 1300 bridges for this application as a permanent install?
View 5 Replies View Relatedmy wireless router that is connected to the internet is in the basement and my computer is upstairs on the second floor of my house. Because of this the signal is very bad, to fix this problem I bought a Belkin Wireless N300 in order to create a wireless bridge but I am having trouble. My downstairs router is a D-Link DI-524 and I have googled all over the place to find a solution but the belkin router doesn't have a wireless bridging option...
View 2 Replies View RelatedI have a Dell Inspiron 1720, that uses a 1300 wireless lan, that keeps crashing. Is there a fix for this, can I replace it with another wireless lan card? Whenever I first start the computer, I would get the error message saying your wireless card had stopped working.
View 4 Replies View RelatedI have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies View RelatedI have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies View RelatedRegion : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
Iv got an "old" dir 655 laying around as my secondary router and found out it had an USB slot for share port.In another room of the house Iv got a media center and an Usb printer. Can I use this dir 655 as a wireless bridge from my main router, so the media center and the printer can be connected? So both low level streaming and shared printer with share port.Or do you need to be connected directly to the dir 655 to use the usb and share port?
View 11 Replies View RelatedI want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View Relatedi just happened to have a spare DIR 601 and I already installed DDWRT on it. Now my question is can make this as a wireless bridge or repeater? with only using the signal of my DIR 655 router upstairs?
View 4 Replies View RelatedI purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since.I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices.
View 2 Replies View RelatedI'm looking at purchasing a Linksys E4200 to replace my WRT54G router, however I also need a Wireless N bridge so I can use it to hook up my HTPC and XBox that's located in my living room.
I'd like to get a bridge that has 4 LAN ports .
My wife has a Dell Inspiron 1300 which crashed. I was able to start it again using the Dell Operating System Reinstallation CD for XP Professional but the wifi (wireless) does not work. Before the crash it had a working wireless connection. It appears that I need to reinstall a driver for it. How can I get a driver when I have no internet connection on that computer? I have tried loading on a flash driver from another computer, but it doesn't seem to transfer. What driver do I need and how can I get it to install on her computer?
View 5 Replies View RelatedIs it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
While I have been VERY happy using my DIR-655 for the most part, all wireless routers have limitations for expansion across your home.I got my TrendNet TEW-640MB installed last night, and it talks to the 655 perfectly, and now I have 4 ethernet ports at distance across my house. I have also used a couple TrendNet TEW647Ga single port wireless bridge for other parts of my home, but with only a single Ethernet port, you still need a little switch/hub to get the extra ports.
Because these units speak .11N at 300 Mbps, it takes full advantage of the technology the 655 gave me when I bought it back in 2009 (??).
If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedI have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View RelatedRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I recently bought the N750 wireless dual band router and I would like to setup a bridge with another router that I'm currently using.
I have followed the instructions in the documentation [URL]. But I've had 0 success in getting this to work.
How to get this feature to work?
Additional info:
I followed each step to the letter. In the last step when my router reboots I noticed that the System light doesn't flash. Which indicates that there is a system error (according to the user manual). But I'm unable to determine what the system error is because I can no longer log into my router's Administration page anymore.
in the instructions (link above) it says to disable DHCP, so I manually assign an IP address to my computer setting the gateway IP address to the IP address I manually assigned to my router. I can see that a connection to the router is established, but I'm unable connect to the internet and when I type in the IP address of my router I'm unable to get into the administration menu.
I checked the wireless connections on my source router and I don't see the IP address of the N750 router.
My lap top and pc were both accessing internet fine. Now my laptop has the message windows cannot config. wireless connection. If you have enabled another prog. to manage this connection use that software. Then it says ifI want windows to config., start WZC service. I am a novice and don't understand any of this. I don't think I have done anything to enable another prog to manage the connection. I have tried reloading isp disc and making new network connection but to no avail. the little network logo has a red x constantly.
View 4 Replies View RelatedWe currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Trying to use TL-WR702N in bridge mode at a hotel. For some reason, every time I set the DHCP parameters to enable DHCP, then save and reboot, upon reboot DHCP is disabled. Of course, without DHCP then bridge mode is useless because I cannot then share the hotel wifi connection with multiple devices.Am I missing something obvious, or is there a trick to getting DHCP to be accepted?
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedI have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedRegion : Others
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
I have an old D-Link DIR-615 wireless N router that I am trying to re-purpose as a wireless bridge so I have network access in the back part of the house where I can't run ethernet wires.
I successfully installed installed DD-WRT on the D-Link and thought I had configured the D-Link into a wireless bridge; however, the D-Link just does not want to communicate with my primary Zoom Cable Modem / Wireless Router. Pings between the two devices return nothing. I disabled all security, they are on the same subnet (192.168.0.1 and 192.168.0.6 for the D-Link), same SSID, etc.
I attached a word doc with screen shots of the settings on both devices.
i got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies View RelatedI want to connect with wireless devices two buildings, one in front of another. Short distance (about 20 meters) and no obstacles. I have a couple of aironet 1242 and i was wondering if it would be possible to setup this link with this equipment.
could WGB be the solution?
I recently discovered the dd-wrt world and am attempting to make a wireless adapter for my Xbox360 using a D-Link DIR615 rev C1 router I purchased and linking it to my home wireless network router (also a D-Link DIR615 but rev B2). I successfully loaded the dd-wrt firmware onto the C1 router and have attempted (multiple times) to set it up for use with my 360 following the instructions posted here at the dd-wrt wiki posting. However, after following the instructions to the letter I have been unsuccessful. After setting it up I can get the router (connected via ethernet to my laptop) to "connect" but it lists the connection as connected to a "unidentified network" with no network access.
View 12 Replies View Related
