TP-Link 150Mbps Wireless :: TL-WR702N Refuses To Allow DHCP In Bridge Mode
Nov 8, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Trying to use TL-WR702N in bridge mode at a hotel. For some reason, every time I set the DHCP parameters to enable DHCP, then save and reboot, upon reboot DHCP is disabled. Of course, without DHCP then bridge mode is useless because I cannot then share the hotel wifi connection with multiple devices.Am I missing something obvious, or is there a trick to getting DHCP to be accepted?
View 11 Replies
ADVERTISEMENT
May 7, 2013
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
View 12 Replies
View Related
Jan 31, 2013
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
View 1 Replies
View Related
Dec 6, 2012
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Am trying to use a TP-Link TL-WR702N to connect my Samsung SmartTV to a wireless network, using "client mode".For some reason, the TV refuses to accept it is connected, or even connected to a router. Enabling DHCP on the TP-Link does seem to convince the TV that it is connected to a router, but still not to the internet. Strangely though, I can control the TV via the Android app operating on the local network, so clearly it is connected. I assume the SmartTV is trying to get a response on the local network that the TP-Link is filtering out for some reason, but no idea why.
View 14 Replies
View Related
Mar 29, 2013
Region : Others
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Going to a hotel where they'll charge me (a lot) for WiFi in the room, for only 1 device. Will the TL-WR702N let me share this 1-device internet connection among several devices?
View 1 Replies
View Related
Dec 5, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
View 2 Replies
View Related
May 4, 2013
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Just got my new TP-Link device and intend to use it in client mode for my new audio receiver to connect to my home network.Trying to configure the device, and I cannot even access the online utility. I tried using the following address:
192.168.0.254
192.168.1.1
None of these seem to work. Tried on Chrome, then Internet Explorer and made sure that the web browser was not set to proxy (it was not set to this in the first place). The address just doesn't seem to connect, and I get a "This page cannot be displayed" note, as if I'm reaching a bad address.
View 1 Replies
View Related
Jan 23, 2013
Region : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
View 3 Replies
View Related
Feb 26, 2013
Region : United-States
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
my Firmware Version is chinese i can't understand it.i go to tp-link.com go to support the last version is older with compare are old.
View 3 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
View 9 Replies
View Related
Apr 13, 2013
Region : Hongkong
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Before my TL-WR702N was working fine as a reperter. After sometime it doesn't work any more, so I try to reset it again but now I couldn't see my SSID after I press the survey buttom in the quick setup - wireless repater page.
View 1 Replies
View Related
May 2, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : India
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP : BSNL
702N runs as repeater mode to W8968. In 702N > Maintenance > Diagnostic the ping work for Internal network but fail for external IPs. Most devices connected to 702 can access Internet fine. I have also tried Bridge and Client mode.
Ping to W8968
Code:
Pinging 10.0.0.1 with 64 bytes of data:
Reply from 10.0.0.1: bytes=64 time=1 TTL=64 seq=1
Ping to Internet
Code:
Pinging 8.8.8.8 with 64 bytes of data:
Request timed out.
View 7 Replies
View Related
Mar 5, 2013
Region : United Kingdom
Model : TL-WR702N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Using a TL-WR702N router as a wireless access point on a narrow-boat. How to print from my i Pad and iPhone to a printer on my narrow-boat, on the UK inland waterways. The Apple store geniuses seem to contradict each other on how it can be done, if at all. I have an i Pad and iPhone and would like to print photos, documents and the occasional web page to my Canon MG4250 printer, which has Air print capability, while I am cruising. I don't have a PC on the boat and of course there is no telephone or broadband connection (other than via 3G on my iPhone). In other words, I want to link my printer to a router, then when required, wireless connect to the router to print from my Apple devices.
Will the TP Link TL-WR702N 150Mbps Wireless N Nano Router allow me to do this? Reading the product information, this nano router looks very flexible, but all five modes mentioned seem to utilize an internet connection. I only have an internet connection via 3G on my iPhone, and can also tether the i Pad to the iPhone's WiFi hotspot to give internet connection on the i Pad. Would I have to use this internet connection somehow, or can I just connect the Apple devices to the printer via the WiFi on the nano router?
In effect I want to create a wireless access point for printing, without any, or at least a regular, internet connection.
View 4 Replies
View Related
Dec 9, 2012
I am trying to determine the best way to setup my E4200 V2 so that it is “uplinked” correctly to a Comcast Dory Modem/router. Currently we have the E4200 V2 router plugged into the Comcast Dory Modem/Router using a CAT6 cable from one of the Ethernet ports on the Comcast device to the WAN port on the E4200. The E4200 is set to “Automatic Configuration - DHCP.”
We are trying to do two things. First better WIFI in the center of the house and for a TV located next to the Comcast device, and second, have all devices in this house see and access all other devices including the Samsung SmartTV, my son’s two systems upstairs, the 3 systems in the room with the E4200, and the one network printer. In the room with the E4200 we have 3 computers and one network printer. 3 of those 4 devices support WIFI so we don’t have to use all 4 Ethernet ports on the E4200.
I see others talking about running the CAT6 cable to an Ethernet port on the E4200 instead of the WAN port and setting it to “Bridge Mode.” Right now the system appears to be working fine although we are sometimes experiencing brief dropped connections with the devices hardwired into the E4200.
Should I be running the E4200 in “Bridge” mode or “Automatic DHCP” mode and which port on E4200 should the CAT6 from Comcast be plugged into?
View 9 Replies
View Related
Dec 4, 2012
Region : UnitedStates
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP :
My TL-WR700N does its job to provide wired internet to my desktop computer from another wireless router via client mode. However, when it is connected, the other wireless clients connected to the primary router lose their connections. To restore those connections, the WR700N must be powered down and the primary router must be restarted.
View 4 Replies
View Related
May 16, 2011
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
View 7 Replies
View Related
May 30, 2012
If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies
View Related
Feb 18, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
View 12 Replies
View Related
Apr 21, 2013
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies
View Related
Apr 6, 2011
So I have a Windows 2008 R2 SP1 Enterprise Server and a gigabit LAN network card onboard. But it refuses to run at gigabit speed and if forced to it, it just says that network cable is unplugged and doesn't work.
I tried switching to a newer and better motherboard (still with gigabit LAN)I have updated drivers.I have checked cables (which are all cat 6 cables and work just fine with other computers in gigabit LAN mode)I've checked and switched ports on the switch and the switch itself...no change. They work just fine with other non-W2008 machines, they get gigabit LAN
I am completely stomped as to what I can do to fix this. It runs just fine in 100 Mbit mode, but can't in any way get it in gigabit mode.I am completely stomped as to why it refuses...is this a limitation of Windows 2008 or something or is there a fix to this?
View 6 Replies
View Related
Dec 25, 2012
Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....
View 3 Replies
View Related
Apr 13, 2011
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
View 1 Replies
View Related
Nov 23, 2010
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows:
DIR-615: 192.168.0.1
DAP-1522: 192.168.0.50 (static)
PC: 192.168.0.55 (static)
View 9 Replies
View Related
Aug 22, 2010
I've got a DIR-655 set in bridge mode after a Cisco router. It's been working great for months, but now I'd like to add a new wireless device and want to get the settings. For the life of me, I can't remember how to access it now.The subnet is 192.168.2.XXX I've got a Mac connected through the "internet" port and a cat5 cable. I figure I should be able to go from 192.168.2.1 through 192.168.2.254 and will eventually find it. Is there something I'm missing?
View 7 Replies
View Related
Jan 15, 2013
I currently have frontier dsl internet and am using the isp provided modem/router combo and a DIR-655. I have the modem running in bridge mode and the 655 set to PPPoe connection, MTU at 1492. I confirmed the MTU setting on the isp modem/router before bridging it. The question i have is if the router MTU is set to 1492 does everything on the LAN side of the router run at 1492 or does it run at 1500 while the router breaks the packets up? Everything works fine but my pc's all use vista and i'm not sure where to check the mtu settings at and all my game consoles are set to mtu automatic so i can't really see what they're running at either.
View 7 Replies
View Related
Nov 22, 2011
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Nov 28, 2012
If you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
A1 - Ralink RT2880+RT2850 chips
[URL]
B1 - Ralink RT3662 chip
[URL]
View 6 Replies
View Related
Apr 25, 2012
I currently have a DAP1522 in Bridge mode with a DIR655. I am only using the 2.4GHz G mode on my 655. In a few days I will be replacing the 655 with an 825. When I log into the 1522 I don't see any settings for Mode, Frequency or Width (while in Bridge mode). The page for wireless setup is blank except for the "Save Settings" button. When I look at the 655, it appears that the 1522 is connected (bridged) at 2.4 GHz G like I would expect. So, when I install the 825 how do I make it connect at 5GHz N or will that be automatic if my SSID on the N mode of the 825 matches SSID on the 1522?
View 1 Replies
View Related
Jun 13, 2012
I have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
View 5 Replies
View Related
Sep 7, 2012
I have a TP link TL-WN722N wireless adapter and it refuses to work on my win7 machine. I've tried installying the cd driver, all the relevant drivers on the TP link website, and the generic atheros driver. I've also tried manually installing all those drivers using device manager to no avail, and it says "a device attached to your system is not functioning"
But I know the physical adaptor is working because I was able to successfully install it onto another computer (it was a windows 8 preview version).
View 12 Replies
View Related
Mar 28, 2013
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Optus
I note that my 4300 never uses two channels in 2.4 GHz wireless n mode as reported by Inssider. I can see a few other routers on Inssider, one of which uses channel 11+7 ALL the time, though it's not a TP-Link router. Mine sometimes will connect to two channels, thus enabling 300 Mbps, but then quickly drops to 1 channel. I believe this is a firmware fault as I only have 3 or 4 routers in the area of my house and I can't believe this would generate sufficient interference to force the router to run at a lower speed. If the router does behave this way by design, then TP-Link should stop advertising it as a 300 Mbps router as it will almost never operate at that speed.
View 4 Replies
View Related
Mar 3, 2013
Region : Canada
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Bell
I'm having to reboot what is now my 2nd router every 1-2 days in order for all connections to resume working. My 2nd router was working great since Saturday afternoon, and just now I needed to reboot in order for my laptop to connect to the network.Now that it seems pretty clear the router in general isn't faulty, I suspected that the issue was IP lease related, so I was looking at DHCP settings and changed the lease time to 2880 (max setting), from 120 (default). However, this should only prolong how often i'll need to reboot the router. So, what is it that's causing my devices to disconnect or not being able to connect to the router for a prolonged period of time?
View 3 Replies
View Related
