if I want to bridge between 2 VLANs ,can I use IRB like I would use in a router for bridging to ethernet interfaces for example?
Config example:
bridge irb
interface vlan 10
ip address 192.168.10.1 255.255.255.0
bridge-group 1
[code].....
I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies View RelatedWE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedI manage IP-PBX(VoIP) in my work place which is consists of switches and a router as shown below,My intend is to seprate between Vlan 1 and Vlan 40, 41.(no packet exchange between vlan 1 <-> vlan 40,41)the Vlan 1 has C class 1 and Vlan 40,41 has C class 40,41.
View 2 Replies View RelatedSite A will have the ip address of 192.168.1.x subnet mask 255.255.255.0 and will need to commmunicate with Site B (ip address 192.168.100.x subnet mask 255.255.255.0). Neither site needs internet access, so I don't have a default gateway. I have a cisco 891 with the ip address of 192.168.1.254. I don't have anything set up on the cisco right now (no running config). Is this possible to set up?
View 11 Replies View Relatedwhen we ping from pc in lan 1 to pc in lan 2, what protocols we walk through in request and in response??
View 14 Replies View RelatedI have a 3 building client currently on a single LAN/subnet/VLAN1. The client wants to install two public APs in their other buildings. I have selected the Cisco WAP4410n for a few reasons, Price, as budget is a factor for them, the 4410n can have up to 4 SSIDs, and can accommodate different VLANs, and it is PoE.
The public side is to have no access to the LAN, just the internet.According to the documents I have read on the 4410, I am to create two SSIDs, one not broadcasted (VLAN1) and one that is broadcasted and public (VLAN2) Both SSIDs would be Isolated from each other.
I assign the switch port attached to the AP to VLAN2, but cannot access the internet. I believe that the two VLANs need to be bridged in either a L3 switch or a router, is this correct? Is that the only way I will be able to get internet access in this situation?A while back someone posted a link to a Cisco workshop. It was set in a spaceship, and the student, me, had to get internet access to different parts of the ship by installing different APs and antennas. Also had to give the people and aliens on the ship different levels of access.
I am trying to configure a UCS 520 and need to setup the VLAN for the phones. I tried to use the vlan command from the config prompt and also from the vlan database and each time I get the following message:
UC520(vlan)#apply
% not enough space on flash to store vlan database. trying squeeze...
% error squeezing flash - (Operation not supported on this file)
Error on database apply 40: NV storage failure
Here is what my nvram is showing:
UC520#dir nvram:
Directory of nvram:/
246 -rw- 6461 <no date> startup-config
247 ---- 1933 <no date> private-config
248 -rw- 6461 <no date> underlying-config
1 -rw- 577 <no date> IOS-Self-Sig#1.cer
2 -rw- 0 <no date> ifIndex-table
3 ---- 61 <no date> persistent-data
262144 bytes total (250626 bytes free)
I have problem with device cisco srp 521 , my problem is haw to create two VLAN-s first will be to WAN link, second for Management.
View 2 Replies View RelatedI got my switch running as a router and several vlans running on it. My question is how do i tie the two vlans together so they can communicate? I know this might be a beginner question.
View 1 Replies View Relatedi'm having troubles with a DHCP server, which is unable to give IPs to hosts that are on a different VLAN than the server.I have this little scenario, one L3 switch (SGE2010-48 without PoE) with 7 different VLANs configured in[CODE]
View 3 Replies View RelatedI just got seriously nice toy to play with, Cisco SG300-10P - I know what you thinking now but with very tight budget...anyway.I configured two ports for VLAN101, Access, but when cabled in and out, it didn't work. Got Linksys switches setup the same way and they work like a charm (and I believe this should too).
View 12 Replies View RelatedI have a question about QoS and how, or if, it functions between a layer 2 switch and a router. My question is, can a frame's COS sent from a layer 2 switch to a router be recognized and converted (mapped) to a DSCP setting without the use of a vlan (not the native vlan1), and can the reverse be done from a router to a layer 2 switch? Can QoS be preserved as it passes through the different devices? I know, pretty basic, but I have to start somewhere.
View 12 Replies View RelatedThe management VLAN(the one I use to connect to the devices) and the native VLAN dont have to be the same VLAN ,right?They are independent and can be different. For instance I can use VLAN 5 for management and 10 as the native VLAN
View 8 Replies View Relatedrouting between VLANs on my ASA 5505. I am very technical system wise, but my knowledge of routing and switching is very shallow.
What I am trying to accomplish: Small lab environment with basic services split onto two seperate VLANs (such that DHCP would need a relay on the second VLAN to deliver leases). No external network connection as of right now (so no Internet).
My current configuration:
Cisco Catalyst 2960
As you can see below, the two VLANs I am trying to set up are vlan101 (10.100.100.1) and vlan102 (10.100.101.1)
Code:
We have created more than 255 Vlans during last 5 years, and we know that eye-catching part of which are unused, I took a report from campus manager searching for Port Attributes to find out which port is assigned to a specific Vlan but as long as there are numerous ports in trunk mode connecting to Virtual servers I can not find out if unused vlans which I exclude from the report I took are really unused or not , how can I find the unused Vlans.
View 2 Replies View RelatedOur network system has 125 different Vlans (Cisco) and I would like to be able to route between only 2 particular Vlans, I know with the command “ip route “ in our layer 3 switches (ws-c3750G -12S) I would be able to route among all Vlans but I need to be able to route between 2 Vlans to be able to access the PCs in vlan 1 from vlan 2 and wise versa
View 1 Replies View RelatedI use the cisco 871 router as a firewall to my home-office. I have configured two vlans for each seperate port. That is, FE0 configured as VLAN 10 ----> connected to Layer 2 Switch, FE1 configured as VLAN 20 ----> connected to another Cisco Layer 2 Switch,FE2 not in use, FE3 not in use and FE4 is connected to WAN.I got 100Mbps speed from the ISP, but I can see that I only get 50mbps even connected to VLAN 10 or VLAN 20.Does configuring two VLANs on Cisco 871 router divides the bandwidth (to Internet) into half?
View 35 Replies View RelatedI am trying to get WOL working across different VLANS on a SG-300-10 Switch in Layer 3 Mode. To achieve this, I've setup an UDP-Relay (GUI menu IP Configuration) for UDP-Port 7 to 255.255.255.255 (this should flood all interfaces with the paket), however, WOL doesn't work across different VLANS. When I am connected directly to the corresponding VLAN, WOL works fine within the same subnet.
View 2 Replies View RelatedI have a cisco 877 router setup with 2 vlan's and 2 dialers, each vlan routed to a dialer. I have some ports forwarded to my vlan 1 incl vpn traffic. I need to get vlan 2 to be able to vpn to vlan 1, and see some of the servers on vlan 1 which are forwarded from router without allowing normal traffic between the 2?
View 2 Replies View RelatedOur network system has 125 different Vlans (Cisco) and I would like to be able to route between only 2 particular Vlans, I know with the command “ip route “ in our layer 3 switches (ws-c3750G -12S) I would be able to route among all Vlans but I need to be able to route between 2 Vlans to be able to access the PCs in vlan 1 from vlan 2 and wise versa.The IP range of vlan1 is 10.0.8.XXX /24 and Vlan2 10.0.11.XXX /24.
View 11 Replies View RelatedHow many VLANs can be managed with the AIR-AP1252AG-E-K9 APs ? My customer wants to manage 4 VLANs, data, voice, guest and another.
View 2 Replies View RelatedWe have cisco 3550 switch i have configure 3 vlans in this switch. i have enable routing between this vlans but vlans not able to communicating with each other.
View 2 Replies View RelatedHow shall i use different vlans outside another gateway in sg-300 28? Example:
vlan2 192.168.2.0/24 gateway 192.168.2.1 outside router gateway 192.168.2.254
vlan3 192.168.3.0/24 gateway 192.168.3.1 outside router gateway 192.168.3.254
should me doing in sg-300 28?
We have our aggregation layer here composed of two N7K with vPC between them. Every access switch is a N5K. Security policies state that we have to filter unnecessary vlans going through the trunk between N5K and N7K. So we use the 'switchport trunk allowed vlan 10,20,30' command. My question is: Do I have to include the native vlan id on this command?
View 10 Replies View RelatedCan I configure two voice vlans on the same physical port?
View 2 Replies View RelatedHow to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies View RelatedThe network topology is like this. Router with DHCP_Server on it.
VLAN 10
VLAN 20
VLAN 30
My question is how to configure the router so that all devices on all 3 VLANS can obtain IP from the router. I've tried to enable proxy arp on all interfaces and create sub interfaces and trunk them to their appropriate vlans, but I can't specify the gateway on all trunked sub interfaces because I get a warning that addresses overlap. Then I tried to set access-group on all sub-interfaces and still doesn't work.
I am trying to connect 2 VMWARE servers directly to my 5515-X firewall. [code]ASDM will not let me assign the same VLAN to both Gi0/2 and Gi0/3. I dont want to connect my VMWARE servers to a switch first (that just adds one more component that can fail).
View 4 Replies View RelatedI have a network that I want to split into 3 VLANs, One for the main traffic, another one for the kids so I can control the sites they visit via opendns and the 3rd for the playstation and the Wii. The catch is that I only want the kids network to access the printer and the NAS on the main network, and then the 3rd network not to be able to access the other 2 vlans. I am trying to perform this via a Cisco 871 router
View 1 Replies View RelatedI just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
I just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
View 5 Replies View Related