Cisco :: Any Possibility To Join AP1121G To 2504 WLC With 7.4.x Version
May 21, 2013
I want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x
View 4 Replies
ADVERTISEMENT
May 22, 2013
I have an allready configured WLC 2504 running in the network. Every LAP i add to the network joins imidiatly to the Controller. But not the AP1121G AP. It fails the Handshake everytime and the Controller shows me an failmessage at the statistics in the GUI. [code]
View 3 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Mar 12, 2013
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies
View Related
Dec 5, 2012
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies
View Related
Oct 1, 2012
Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
May 8, 2013
I have a WLC 2504 with 10 licences running 7.3.2.112.0. I have 7 AP joined from different remote sites (WAN). The other APs are 3602E.
I got a brand new 3602I that I want to join, from a remote site and I am getting these error messages and cannot join :
*Dec 21 14:35:18.859: %CAPWAP-5-DHCP_OPTION_43: Controller address x.x.x.x obtained through DHCP,
As far as I can tell, the AP seems to be loosing packets that are coming/going away from its own subnet.
AP address : 192.168.1.1 (mask 255.255.255.0)
WLC address : 192.168.2.1 (mask 255.255.255.0)
If I ping the AP address from a computer in the *same subnet*, I get a perfect 0% packet loss.
If I ping the AP address from a computer in ANY *other subnets*, I get about 50% packet loss.
If I ping anything else *other than this single AP*, to and from any other subnets, I get a perfect 0% packet loss.
Only packets orginating or sent to the AP from other subnets are getting lost.To me it looks like there is something wrong with the routing table of the AP, as if some packets were not properly returned ?
View 3 Replies
View Related
Sep 10, 2012
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies
View Related
Sep 17, 2012
We have bought an 2504 Wireless Controller and now i want to download the newest Software, actually the Wireless Controller runs release 7.2.103. In the download section from Cisco i've found two "latest versions" the 7.0 with release date from 11.09.2012 and the other 7.3 with the release date 30.08.2012.
Now I'm a bit confused about this, because the higher release has an lower release date : Can you tell me the difference between this versions? and which version i should install?
View 7 Replies
View Related
Apr 23, 2013
Just purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
View 1 Replies
View Related
May 7, 2013
I have a cisco wlc 2504 is deploying authentication services to guest users toward a portal web customized and configured. I need to install my certificate verisign (certificate.cer) in to cisco wlc because my users don't like the page no trusted (The wlc is showing me ''There is a problem with this website's security certificate'') when they are trying to access to ssid to users guests.
View 2 Replies
View Related
Feb 27, 2011
I want to convert LAP AIR-AP1121G-E-K9 to autonomous AP.
View 1 Replies
View Related
Feb 12, 2012
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction. Also attached is a result table of ping attempts through the ap1121wgb from each side. I don't have a problem with the wireless connections. The ap1121g's associate ok. Based on the ping results the problem appears to be in the ap1121g-wgb configuration. The following two cisco documents have been my main reference, besides the cisco command lookup site.URL
View 17 Replies
View Related
Jul 6, 2011
When a ap1121G joins WLC4404,it shows a normal heatmap in WCS. But when a ap1121G joins WLC5508,the RSSI in whole coverage is almost -35 dbm.I copy the heatmaps to the attached files.
The versions are as below.
WCS 6.0.196
WLC5508 6.0.200.29
WLC4404 5.2.157
View 8 Replies
View Related
Oct 4, 2011
In CLI we have users log in at priv 1 and use "enable" to increase privilege and do configurations. This allows "accounting" of command history. On the AIR-AP1121G-A-K9 (12.3(8)JED1) I cannot duplicate this for http login.
I can log in as a user at priv 1. When I try to go to a privileged link like "Security" I get prompted for a second login/pw. Nothing works here unless I have a second user defined at priv 15 and enter that login/pw. The problem is - that login/pw can be used to log in via http in the first place which bypasses accounting of the actual user. It also allows login to the CLI at priv 15 which I cannot permit.
username test1 secret 5 abcdxxx
username test2 privilege 15 secret 5 efghxxx
enable secret 5 ijklxxx(code)
View 1 Replies
View Related
Sep 14, 2009
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies
View Related
Feb 1, 2011
I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?
View 5 Replies
View Related
Oct 8, 2012
Recently we upgraded a switch with an image from the repository in LMS. After the installation of the image it seemed corrupt.
My question now is : Can we do a MD5 checksum on all the images in the local repository to verify that all images are ok to use?
View 2 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
Mar 2, 2012
i have IO digital cable and internet and they offer free WiFi which i do not use my modem is wired to my pc but over the last few weeks my connection has been sluggish now is it possible for one of my neighbors to be using my internet?
View 2 Replies
View Related
Dec 28, 2012
I heard my brothers' conversation in our house. One was asking another, if he is downloading things. The other one replied, saying no, he didn't. And then the one that was asking said, he knew he was lying. He can detect and monitor that person's IP address to know enough if the other person is downloading or not.
View 6 Replies
View Related
Nov 23, 2011
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies
View Related
Apr 15, 2007
I got a weird problem with a PIX 515 (7.2(2).18.I'm natting SIP behind the Firewall [code] Incoming and outgoing SIP-calls are working perfectly. See old conversation [code] Unfortunately, "forwarding-all" function (with a SIP-incoming call to an external number [through the same SIP-Proxy]) is sending the SIP-signal (ringing) but no RTP-flow.
On the PIX the "SIP inspect" is activated.Is there a possibility to configure a symmetric / consistent NAT on the PIX to allow the RTP-stream to be built up?
View 2 Replies
View Related
Mar 8, 2012
I was wondering how would it be possible for a person to gain access to computer through my router? Or is that even possible? Just a quick rundown, the past few weeks, 2 of my email accounts have been compromised, one was email i had for years, the other was a new random email that i rarely use. In the same week, both these accounts were "hacked" the passwords were changed and i can't get access to them. Same goes for my fb account also compromised. These emails aren't linked to the fb acct neither. I know you might think yeah, i might have clicked on one of these phishing links, but i assure you haven't, i have never entered any of my information on random sites or anything like that. Actually i only really frequent 5 or 6 sites on this certain laptop and i have never downloaded anything on it but songs from iTunes.
I've scanned my computer numerous times, and even went as far as to factory reset it, so i don't know how high the possibility of me having a key logger is.So i guess i'm asking, how would a person be able to have gained access to computer w/o having it in their physical possession? Can i be getting hacked through my wifi connection? What information of mine would someone have to have in order to access my computer and monitor my web activity?
View 3 Replies
View Related
Oct 12, 2011
I got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies
View Related
Mar 24, 2013
I have a switch from SG 500 Series the works as Layer 3 Routing Switch with the Firmeware 1.2.7.76. I have create some diferent VLAN´s and have defined one ACL for each VLAN. Now i try to do a binding from the ACl to a VLAN but i have only the option to bind the ACL to a phys. Interface or a LAG.is the a possibility to bind the ACL to a virtual interface like in other Cisco serieses and how it works ? the Backround is i have connectetd 2 Hyper-V Server where the Guests are in different VLAN´s and the server is connectetd with a 10Gb Trunk to the Switch now the switch routed the different VLAN´s and i must have some restrictions between the VLAN´s.
View 2 Replies
View Related
Sep 17, 2012
Is it possible to implement LLQ(QoS) on ethernet modules in the Cat 6500? For this feature, I can only find documentation about ES+ modules or SPA/SIP modules! (according to the feature navigator LLQ is supporten on the concerning HW and SW image)
View 2 Replies
View Related
May 15, 2013
F7D4402nt play 600. i updated to windows 8 and the supplied software will not work. The software was very easy for a setup. Now i must do the things the hard way. a completely manual setup. it is a bit of a chore.
View 1 Replies
View Related
Nov 28, 2012
I have a Dell XPS L502x (Core i7, 6 GB RAM, 2GB NVIDIA graphic card, 750 GB HDD)My laptop does not have HSPA mini card
Is there a possibility to add a HSPA mini card
View 2 Replies
View Related
Apr 15, 2013
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V1
Firmware Version :
ISP :
I will soon be moving to somewhere without DSL service. I was wondering if it is possible to connect my iphone 4 to the usb of the mr3220 and use the iphone's 3g data allowence?
View 1 Replies
View Related
Jan 7, 2013
I'm looking at the possibility of purchasing a few 3750 to build a switch stack to replace my current core and access switches. I'd like for the stack to support server, SAN, and user traffic, as well as provide simple switch management, redundancy, and failover. I've also been looking at the 4500, 6500, and Nexus series switches (although the Nexus switches maybe a bit too much for my network).
My current environment consists of 3560's as the core/distribution/access switches, a mixture of Hyper-V and VMWare environments (although we're slowly migrating to Hyper-V), an HP SAN (P4500), and about 100 users. Any issues going with the 3750's or have an alternative, more efficient solution?
View 8 Replies
View Related
Nov 20, 2012
Normally when we do HSRP with vPC on N7K the device will be Active/Standby in control plane but it will be Active/Active in data plane. In this case any traffic reach to standby device it can forward traffic directly to uplink which is not my desire. My goal is all traffic should pass through active (control plane) device in every case unless active device totally dead. So Is it possible for Nexus 7000 to be HSRP Active/Standby in Data Plane ?
View 4 Replies
View Related
