I have an allready configured WLC 2504 running in the network. Every LAP i add to the network joins imidiatly to the Controller. But not the AP1121G AP. It fails the Handshake everytime and the Controller shows me an failmessage at the statistics in the GUI. [code]
View 3 RepliesI'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies View RelatedI have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedConverted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies View RelatedI want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View RelatedI have a WLC 2504 with 10 licences running 7.3.2.112.0. I have 7 AP joined from different remote sites (WAN). The other APs are 3602E.
I got a brand new 3602I that I want to join, from a remote site and I am getting these error messages and cannot join :
*Dec 21 14:35:18.859: %CAPWAP-5-DHCP_OPTION_43: Controller address x.x.x.x obtained through DHCP,
As far as I can tell, the AP seems to be loosing packets that are coming/going away from its own subnet.
AP address : 192.168.1.1 (mask 255.255.255.0)
WLC address : 192.168.2.1 (mask 255.255.255.0)
If I ping the AP address from a computer in the *same subnet*, I get a perfect 0% packet loss.
If I ping the AP address from a computer in ANY *other subnets*, I get about 50% packet loss.
If I ping anything else *other than this single AP*, to and from any other subnets, I get a perfect 0% packet loss.
Only packets orginating or sent to the AP from other subnets are getting lost.To me it looks like there is something wrong with the routing table of the AP, as if some packets were not properly returned ?
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies View RelatedI updated an AP1121 accidentally with the LWAPP version of an AP1130ag.
View 1 Replies View RelatedI'm having an issue with a 1252 LAP that is connected to the WLC over a WAN link.Basically, it won't associate. The following is taken from a console into the LAP:
*Mar 1 00:00:07.799: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:08.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.851: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.003: Logging LWAPP message to 255.255.255.255.
[code].....
The ap-manager interface is configured correctly and there isn't a duplicate IP address. The LAP was initially stand alone and was converted to LWAPP.The MTU over the WAN link is 1500 bytes.All I'm getting from the WLC debugs is:
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Received LWAPP DISCOVERY REQUEST from AP 00:22:xx:xx:xx:xx to 00:19:xx:xx:xx:xx on port '29'
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx LWAPP Discovery Request AP Software Version: 0x3003300
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Successful transmission of LWAPP Discovery Response to AP 00:22:xx:xx:xx:xx on port 29
So basically the join messages don't seem to reach the WLC. In fact they don't even seem to reach the local router on the remote subnet. The discovery packets are seen on the local router but the joins don't seem to appear at all.I'm not sure if it's a latency issue. Average latency over the WAN link is under 70ms.I'm assuming the certificate on the WAP is MIC and the MAC details have been entered into the WLC AP Security policies for authentication. I'm not seeing any debugging messages relating to bad authentication at all.I can't debug from the LAP as it's LWAPP, obviously.We're running WLC version 4.2.130.0.
I connected the AP [1140 - Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)] to the switch (3560) and the switch with the WLC (5500 series), but I get the below error:
*Nov 7 09:07:59.916: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 192.168.10.22:5246
*Nov 7 09:07:59.954: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code]....
The access point cannot join the controller. Is this a misconfiguration at the WLC or something else?
I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0
I am trying to lab up an ACS5.2 with windows 2003 AD for PEAP authentication. But my ACS does not join the AD and throws an error "can not resolve network address". But when i do an nslookup on ACS CLI , the same domain wireless.abc.com is returning with the IP address of my AD. I think i am missing something in windows AD/DNS configs here as i am not a windows AD expert.
1) My AD domain is wireless.abc.com. In my DNS, i have a zone called wireless.abc.com. and i have added "New Host" in that DNS zone with the "name" as blank and providing IP address of my AD (AD and DNS are on same windows installation) . Is this the right way to do ?
2) I should be entering "wireless.abc.com" in the ACS active directory domain name field and do test connection. right ?
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC
WLC software 7.2.103.0
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30
[code]....
Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.
2 . Second problem.: Operational Status = UNKNOWN
Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies View RelatedMy WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
Airlap 1041n i have air lap 1041n(soft version 12) and wlc 2112 i dont have dhcp server perhaps i use tftpd32 to act as a dhcp server.
my problem is
1. i have configured the wlc 2112 and it's ip is :172.25.1.1
2. i cant configure the air lap 1041n. when i enter the cli mode the following message comes ****continuously***:
Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 01:44:11.310: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
3. my question is how to stop this continuous mgs ?
4. how can i assign an ip to my AP ?
5. how can i join my AP with MY wlc ?
I have to show my office that i can control two ari lap 1041n-k9 with my WLC 2112 and my laptop's wifi and cellphone's wifi are able to get connected with the Access points.
l have a new ACS v 5.2 appliance and l´m trying to join to my domain, but l haven´t could, the acs shows me the Clock skew error, and l was checking some documents about it doesnt work. the acs have the same timezone and time that my domain, but the problem persist
View 7 Replies View RelatedI am trying to join my ACS 5.1 to my AD. In the External Identity Stores > Active Directory I have put in the AD administrator details and hit the test button and the test succeeds.
However, when I try to save changes it fails with an eror saying it can't connect to the LDAP server.
Error while configuring Active Directory:Error while configuring Active Directory:Unexpected LDAP Error Can't contact LDAP server due to unexpected configuration or network error.Please try the --verbose option or run 'adinfo --diag' to diagnose the problem.Join to domain 'Mydomain.local', zone 'null' failed.
I have done this lots of times and never had any issue once the test connection succeeds.
I've checked the time and timezones on both ACS and AD and they are the same.
I have a 4400 WLC for 100APs running the 7.0.98.0software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)
How to I join two ethernet cables without using a switch ?They are same as cat5 cables right ?Is there some sort of adapter to connect two together ?
View 1 Replies View RelatedMy computer was connected to a workgroup, we shared the same internet wireless connection, my printer is shared, but my officemate can't find my computer in their network places... I try all the ways given from the internet but nothings change... I'm been working for this for 2 days already
View 7 Replies View Relatedi don't know how to connect to a network, to make an ipad work
View 1 Replies View RelatedI'm having issues joining a remote PC to the corporate domain. The VPN we're using is SonicWall.Here's what the error is: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the fileC:Windowsdebugdcdiag.txt.The domain name "creatormail" might be a NetBIOS domain nameIf this is the case, verify that the domain name is properly registered with WINS.If you are certain that the name is not a NetBIOS domain name, then the following informationubleshoot your DNS configuration.The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller (AD DC) for domain "creatormail":[CODE]
View 3 Replies View RelatedHave two wifi in my area but can't get on them what do I need to do
View 1 Replies View Relatedhow do I get Ipod to join network....my ipad works just fine?
View 1 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View Related